Quadra-Fire QVI-25FB-S owner manual Placing, Securing and Leveling the Appliance

Page 13

CUT AND BEND

FLASHING AS NEEDED

TO FIT CHIMNEY

SEALANT

ADHESIVE

Figure 7.2

•Trim chimney top plate to minimize excess overhang or bend over flue tile (see Figure 7.2).

•Place 3/8 inch bead of 300º F silicone on flue tile top.

C.Placing, Securing and Leveling the Appliance

•Install insert (without surround attached) into existing fireplace while pulling collar slide plate forward.

•Install gas line into hole provided on insert side.

•If applicable install remote control wires into insert side (see Section 6, F.).

•Secure collar slide plate to appliance by placing locking handle into position with locking tabs (see Figure 7.1) and secure with #8 screw.

•Level the appliance from side to side and front to back. If necessary, use the leveling legs included with the manual bag to set each corner of the base.

•Position any excess flexible vent pipe back up into chimney without sagging. Twist and push flex vent together to shorten.

•Install fiberglass insulation pieces to back face of surround.

•Attach surround. Follow instructions accompanying surround.

•Push insert so that surround becomes tight against face of fireplace.

WARNING

Fire Risk.

Only an approved Hearth & Home Technologies surround may be used to cover integral grills on solid fuel burning fireplaces.

• No other components such as shrouds, sheet- metal plates, etc., may be used to seal off vents.

WARNING

Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

WARNING

Explosion Risk.

Combustion Fume Risk.

•Connect vent sections per installation instructions.

•The 3 foot section of stainless steel flexible pipe MUST be attached directly to the exhaust collar on the collar slide plate.

•Connect exhaust vent pipe ONLY to exhaust starting collar and termination cap center collar.

•Connect inlet air vent ONLY to inlet air collar on appliance and either the termination cap inlet air collar OR terminate within chimney.

•Do NOT allow vent to sag below connection point to appliance.

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents What to do if you smell gas ModelHOT Surfaces Xxxxxxxx Homeowner Reference InformationTable of Contents Listing and Code Approvals Getting Started Design and Installation ConsiderationsInspect Appliance and Components Tools and Supplies NeededMinimum Fireplace Opening Fireplace Size RequirementsClearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsVent Table Key Vent Information and DiagramsHorizontal Venting Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Locking TAB Handle Placing, Securing and Leveling the Appliance Masonry Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalFuel Conversions Gas Connection Gas InformationGas Pressures Check for GAS Leaks High Altitude InstallationsON/OFF Switch Wiring the ApplianceElectrical Information Appliance RequirementsInstallation for Fan Optional Junction Box InstallationOptional Accessories Fan Wiring Diagram Mantel Projections FinishingClean the Appliance Appliance SetupAccessories Ember PlacementLog Placement Log Set Assembly LOGS-2031Positioning the Logs Quadra-Fire QVI-25FB-S 2031-910 Rev. D 3/08 Air Shutter Setting Glass AssemblyRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsBefore operating this appliance have a qualified technician Standing Pilot Ignition Lighting ApplianceWhat to do if YOU Smell GAS Pilot Adjustment Initial Break-in ProcedureCheck Pilot Flame Appearance After Appliance is LitIssue Solutions Frequently Asked QuestionsSymptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingMaintaining and Servicing Appliance Maintenance TasksDoors, Surrounds Inspect Maintenance TasksQVI-25FB-S Model Dimensions Appliance Dimension DiagramReference Materials Direct Vent Flex Liner Kits Vent Kits ComponentsService Parts List Log Set Assembly119 1312 Part number list on followingStocked Service PartsAt Depot Valve Assembly Limited Lifetime Warranty Lifetime WarrantyContact Information
Top Page Image Contents