Quadra-Fire QVI-25FB-S owner manual Installing Vent Pipe and Appliance, Venting Components

Page 11

7 Installing Vent Pipe and Appliance

A. Venting Components

CAUTION

Sharp Edges

•Wear protective gloves and safety glasses during installation.

The vertical vent termination system installed on this model includes:

•One 3-foot section stainless steel ﬂexible pipe (included with insert).

•One length of 3-inch ﬂexible vent pipe for combustion air (included with vent kit).

•Flexible vent pipe for exhaust air (included with vent kit).

•One pipe-to-cap adaptor (included with vent kit).

•One vertical termination cap (included with vent kit).

B. Connecting Vent Pipe

Reference instructions in the termination kit.

•Install the 3-inch ﬂexible vent pipe(s) down through the chimney.

•Secure the exhaust ﬂexible vent pipe to the 3 foot section stainless steel flexible vent pipe using the factory- installed 3-inch collar in the stainless steel section of pipe (see Figure 7.1).

•Use 3 screws to attach either a 4 foot or 30 foot section of inlet air vent to the inlet collar on the collar slide plate (see Figure 7.1). NOTE: The collar slide plate may be removed from appliance to aid installation.

•Seal opening between ﬂex vent and chimney just above insert. Unfaced ﬁberglass insulation may be used for this purpose.

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08

11

Image 11

Contents HOT Surfaces ModelWhat to do if you smell gas Xxxxxxxx Homeowner Reference InformationTable of Contents Listing and Code Approvals Tools and Supplies Needed Design and Installation ConsiderationsGetting Started Inspect Appliance and ComponentsMinimum Fireplace Opening Fireplace Size RequirementsClearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsMeasuring Standards Vent Information and DiagramsVent Table Key Horizontal VentingInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Locking TAB Handle Placing, Securing and Leveling the Appliance Damper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Wood BurningGas Pressures Gas InformationFuel Conversions Gas Connection Check for GAS Leaks High Altitude InstallationsAppliance Requirements Wiring the ApplianceON/OFF Switch Electrical InformationOptional Accessories Junction Box InstallationInstallation for Fan Optional Fan Wiring Diagram Mantel Projections FinishingEmber Placement Appliance SetupClean the Appliance AccessoriesPositioning the Logs Log Set Assembly LOGS-2031Log Placement Quadra-Fire QVI-25FB-S 2031-910 Rev. D 3/08 Replacing Glass Assembly Glass AssemblyAir Shutter Setting Removing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance What to do if YOU Smell GAS Lighting ApplianceStanding Pilot Ignition After Appliance is Lit Initial Break-in ProcedurePilot Adjustment Check Pilot Flame AppearanceIssue Solutions Frequently Asked QuestionsStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action TroubleshootingMaintaining and Servicing Appliance Maintenance TasksDoors, Surrounds Inspect Maintenance TasksReference Materials Appliance Dimension DiagramQVI-25FB-S Model Dimensions Direct Vent Flex Liner Kits Vent Kits ComponentsPart number list on following Log Set AssemblyService Parts List 119 1312At Depot Service PartsStocked Valve Assembly Limited Lifetime Warranty Lifetime WarrantyContact Information