Quadra-Fire QVI-25FB-S owner manual Termination Locations, Vent Termination Minimum Clearances

Page 8

4 Termination Locations

A. Vent Termination Minimum Clearances

Figure 4.1 specifies minimum vent heights for various pitched roofs.

HORIZONTAL

OVERHANG

WARNING

Fire Risk.

Asphyxiation Risk.

Terminations MUST meet minimum clearances.

Exhaust gases are hot.

Nearby vents may draw fumes into house.

2FT.

MIN.

GAS DIRECT VENT

TERMINATION CAP

20 INCHES MIN.

VERTICAL

LOWEST

WALL

 

DISCHARGE

 

OPENING

 

X

12

ROOF PITCH

IS X/ 12

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

Roof Pitch

H (Min.) Ft.

Flat to 6/12

1.0*

Over 6/12 to 7/12

1.25*

Over 7/12 to 8/12

1.5*

Over 8/12 to 9/12

2.0*

Over 9/12 to 10/12

2.5*

Over 10/12 to 11/12

3.25

Over 11/12 to 12/12

4.0

Over 12/12 to 14/12

5.0

Over 14/12 to 16/12

6.0

Over 16/12 to 18/12

7.0

Over 18/12 to 20/12

7.5

Over 20/12 to 21/12

8.0

* 3 foot minimum in snow regions

Figure 4.1 Minimum height from roof to lowest discharge opening

8

Quadra-FireQVI-25FB-S2031-910 Rev. D • 3/08

Image 8
Contents HOT Surfaces ModelWhat to do if you smell gas Homeowner Reference Information XxxxxxxxTable of Contents Listing and Code Approvals Design and Installation Considerations Getting StartedInspect Appliance and Components Tools and Supplies NeededFireplace Size Requirements Minimum Fireplace OpeningClearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesVent Information and Diagrams Vent Table KeyHorizontal Venting Measuring StandardsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Locking TAB Handle Placing, Securing and Leveling the Appliance Installing Adaptor and Termination Cap MasonryFactory Built Wood Burning Damper Flashing Kit OptionalGas Pressures Gas InformationFuel Conversions Gas Connection High Altitude Installations Check for GAS LeaksWiring the Appliance ON/OFF SwitchElectrical Information Appliance RequirementsOptional Accessories Junction Box InstallationInstallation for Fan Optional Fan Wiring Diagram Finishing Mantel ProjectionsAppliance Setup Clean the ApplianceAccessories Ember PlacementPositioning the Logs Log Set Assembly LOGS-2031Log Placement Quadra-Fire QVI-25FB-S 2031-910 Rev. D 3/08 Glass Assembly Air Shutter SettingRemoving Glass Assembly Replacing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance What to do if YOU Smell GAS Lighting ApplianceStanding Pilot Ignition Initial Break-in Procedure Pilot AdjustmentCheck Pilot Flame Appearance After Appliance is LitFrequently Asked Questions Issue SolutionsStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsReference Materials Appliance Dimension DiagramQVI-25FB-S Model Dimensions Vent Kits Components Direct Vent Flex Liner KitsLog Set Assembly Service Parts List119 1312 Part number list on followingAt Depot Service PartsStocked Valve Assembly Lifetime Warranty Limited Lifetime WarrantyContact Information