Monessen Hearth TPB30, TPB24, TPB18 manual Fireplace and Hearth Dimensions, Hearth Minimum Dimension

Page 9

FIREPLACE AND HEARTH DIMENSIONS

WARNING

This appliance is for installation only in a solid-fuel burning masonry or UL127 factory- built fireplace, vent free appliance, or in listed ventless firebox enclosure. It has been design certified for these installations.

Exception: DO NOT install this appliance in a factory-built fireplace that includes instructions stating it has not been tested or should not be used with unvented gas logs.

Use manufacturer's installation and clearance requirements as defined in their manual.

The TPB Series unvented room heater is approved for installation into the following unvented fireplaces:

GCUF Series Fireboxes Magnum36/42, Lo-Rider36 or BUF

The TPB Series unvented room heater may also be installed into a Ventless Firebox Enclosure for Gas Fired Decorative Type Unvented Room Heaters per IAS Requirement No. 2-97 ANSI Z21.91-2001 (typically referred to as a "Universal Firebox"), as long as firebox hearth dimensions meet the minimum hearth dimensions shown below.

Model

A

B*

C

D

TPB18

26"

13"

18"

17"

 

 

 

 

 

TPB24

29"

13"

221/4"

17"

TPB30

33"

13"

251/4"

17"

* Without front grate installed "B" will be 12 ½.

C

D

A

B

Figure 2 - Hearth Minimum Dimension

70D0004

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents What to do if YOU Smell GAS Read and Save These InstructionsContents Important Safety Information InstallerOwner Massachussetts Residents only What YOU will Need for Installation Getting StartedMake Sure YOU have Received ALL Parts Product Features and Specifications General Installation Information CodesAdequate Combustion and Ventilation AIR BTU / Hr = Hearth Minimum Dimension Fireplace and Hearth DimensionsHeight of Restriction Minimum Depth of Fireplace/Firebox Placement in a Fireplace with a Restrictive BarrierSidewall and Ceiling Clearances Clearances and Height RequirementsClearances and Height Requirements Measuring Heat Resistant Material for Mantel Minimum Mantel Clearance with No Hood -TPB18 Mum of 10 at a minimum of 28 above the opening Minimum Clearance above Combustible Flooring Floor ClearanceBefore Fully Installing the Unit Installing Vented ApplicationsBefore Installing the Appliance Damper Stop InstallationInstalling Vented Applications Assembly ProcedurePlacing and Securing Appliance Flexible Tube Manual Shutoff Gas Supply Inlet Valve Connecting the GASMILLI-VOLT Valve Control Figure Checking GAS PressureElectrical Wiring MILLI-VOLT Connecting Optional Wall Switch or ThermostatATE Connecting Remote Receiver Checking System OperationComplete MILLI-VOLT System Check Installing Charred Timber Logs on Burner LOG PlacementInstalling Left Base Log #3 Installing Left Top Log #5 Placing Rock Wool Installing Right Top Log #6Riser and Steel BAR Grate Installation Optional Riser InstallationSteel BAR Grate Installation Optional Cast Iron Grate and Andiron Installation Cast Iron Grate InstallationAndiron Installation Placing the Decorative Rock Flame AppearanceChecking the Pilot Flame MILLI-VOLT Control and Thermostat ControlOperating Instructions Checking the Burner FlameWhat to do if YOU Smell GAS Operating InstructionsTo Turn OFF GAS to Heater Cleaning and Servicing Operating Instructions and Cleaning and ServicingObserved Problem Possible Cause Remedy TroubleshootingODS/pilot lights, but flame Burner Assembly Replacement PartsAccessories Sold Separately Replacement Parts ListCTCL18 CTCL24 CTCL30 Charred Timber Logs70D0004 Carbon Monoxide Detector Requirements Special Requirements Lifetime Warranty Five Year WarrantyBasic Warranty
Top Page Image Contents