Monessen Hearth MJ27PR, MJ27NR operating instructions To Turn OFF GAS to Heater

Page 31

OPERATING INSTRUCTIONS

Millivolt CONTROL LIGHTING INSTRUCTIONS

1.STOP! Read the safety information label.

2.Make sure the manual shutoff valve is fully open.

3.This gas log set is equipped with an ignition device (piezo) which automatically lights the pilot. If piezo ignitor does not light the pilot, refer to instructions for Match Lighting Instructions, Page 30.

4.Turn gas control knob clockwise to the OFF position and turn ON/OFF switch to OFF position.

5.Wait (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP!

Follow the instructions under What To Do If You Smell Gas, Page 30.

6.From OFF position, turn the gas control knob counterclockwise to IGN position. Push in control knob for 5 seconds. NOTE: If you are running the heater for the first time, it may be necessary to press in the control knob for 30 seconds or longer to allow air to bleed out of the gas piping.

7.With the control knob pushed in, push in and release the piezo ignitor button to light the pilot.

8.Continue pushing the control knob in for a further 60 seconds to prevent the flame detector from shutting off the gas while the probe is warming up. Release the control knob.

9.Turn gas control knob counterclockwise to the ON position.

10.After the pilot has been lit for one minute, the burner can be turned on.

a.Slide the three (3) position button on the remote receiver to the ON position and the main gas flame should ignite in the Max. Height Setting.

b.Slide the button to OFF and the main gas flame should extinguish.

c.Slide the button to RS (the center position), press the ON button on the handheld transmitter to turn the system ON. The main gas flame should ignite in the Max Height Setting.

d.Press the OFF button to decrease flame height. Press the OFF button twice to lower flame level. Press the OFF button three times to turn main burner OFF.

11.If the gas logs will not operate, follow the instructions To Turn Off Gas To Heater below and call your service technician or gas supplier.

Figure 35 - Pilot

TO TURN OFF GAS TO HEATER

1.Turn control knob clockwise to OFF position to completely shut off the heater.

2.If applicable: Turn ON/OFF switch to OFF position and/or set thermostat (if present) to lowest setting.

3.If applicable: Turn off all electric power to the heater.

86D0024

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Natural Gas or Liquid Propane Control Type Millivolt Hi/Low Models MJ27NR, MJ27PRContents Gas Code, Ansi Z223.l/NFPA54 Important Safety InformationInstaller OwnerUtility gas wells. This gas is commonly Never connect unit to private nonKnown as wellhead gas Getting Started What you will need for installationMake sure you have received all parts Product Features and Specifications National Fire Protection Association, Inc General Installation InformationCodes American National Standards Institute, IncBTU / hr = Minimum Hearth Dimension Fireplace and Hearth DimensionsHeight of Restriction Minimum Depth of Fireplace/Firebox Placement in a fireplace with a restrictive barrierSidewall and Ceiling Clearances Clearances and Height RequirementsHeat Resistant Requirements for Safe InstallationMeasurement MJ27 Mantel, Shelf or Other Combustible Projection Heat Resistant Requirements for Safe Installation with Wood12 min Is an example of an unsafe mantel instal Minimum Clearance above Combustible Flooring Floor ClearanceFireplace Preparation Before installing in a solid fuel burningPaint by a qualified chimney cleaner Installing Vented ApplicationsAssembly procedure Installing Vented ApplicationsPlacing and Securing Appliance Gas Connection Connecting the GASMillivolt Valve Control Figure Checking GAS PressureAte Electrical Wiring MillivoltTo touch grate or Connecting Remote ReceiverDo not allow wires BurnerLOG Placement Install Log #8 Install Log #4 Place Flickering Bright Embers Place Flickering EmbersPlacing the decorative rock Andiron and rock installationANDIRON Installation Assembly InstructionsChecking the pilot flame Flame AppearanceOperating Instructions Checking the Burner FlameWhat to do if YOU Smell GAS Operating InstructionsTo Turn OFF GAS to Heater Cleaning and Servicing Operating Instructions / Cleaning and ServicingTurn appliance OFF and allow to cool before TroubleshootingServicing. Only a qualified service person Should service and repair the heaterGoes out when control Description Qty Replacement partsLogs Replacement Parts listDescription Qty MJ27 Please Read and Follow These 86D0024 If Warranty Service is Needed Lifetime WarrantyFive Year Warranty Basic WarrantyMhsc
Top Page Image Contents