Monessen Hearth 36CDVXTRN installation instructions Side view of final unit location

Page 15

Finished

Wall

 

 

Secure with Screw

 

Vent Termination

 

C

 

L

 

22”

 

(559 mm)

 

Firestop

 

FP1005a

Fig. 19

Side view of final unit location.

CDVX Series Direct Vent Gas Fireplace

 

Termination

C

 

L

 

to Floor

Flex Section

29 ” Appliance

56O Collars

(749 mm)

FP1473

Fig. 20 Grasp the vent pipe close to the collar and bend to 45° angle. Do not exceed 45°.

Rear Wall Vent Installations -

45° Flex Vent Pipe

Using Kit 7TCD45KT

NOTE: The corner placement dimensions on Page 5, Figure 1 of the manual must be adhered to! Figures 20 & 21 show general installations. Refer to instructions below for a detailed description of instal- lation.

1.Determine where the termination is to be in- stalled. Locate the center of the hole 29Z\x” (749 mm) off the floor. (Fig. 20)

NOTE: The location of the termination hole must be adhered to!

2.Install the firestop as shown on Page 14.

3.Remove the flex vent and extend the flex vent out to its longest length.

4.Bend the tab on the back of the fireplace up. (Fig. 18)

5.Insert the collar on the flex vent that has the twist lock embosses on it onto the collar of the fire-

place. Twist the collar to “lock it” onto the fireplace. Run a screw through the tab and into the collar to secure the collar onto the fireplace.

6.Bend the flex pipe up 90° as close to the fireplace as possible. (Fig. 21)

7.Slide the fireplace partially into the corner and, while holding the vertical portion of the flex vent pipe, grab the exposed end collar and bend it down to the height of the opening in the wall.

8.While pushing the unit in place, slide the collar through the firestop. NOTE: It may be necessary to trim some material off of the collar. The collar is made long to accommodate brick finished houses. (Fig. 23)

9.Secure the collar in place by running a screw through the tab in the firestop and through the col- lar.

10.Slide the termination into the collar and secure with the 4 screws provided. (Fig. 23)

20012253

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Builder Direct Vent Models Table of Contents Certified To Installation & Operating InstructionsGas Equipment Venting System not Provided Requirements for the Commonwealth of MassachusettsFireplace specifications and framing dimensions Fireplace Dimensions Rear Vent1756 203 mm 435 mm 166 422 mm Fireplace Dimensions Top VentMantels Mantel ChartLocating Your Fireplace Clearance to CombustiblesFinal Finishing Hood InstallationHearth Framing and FinishingGas Inlet and Manifold Pressures Gas SpecificationsGas Line Installation Remote ON/OFF SwitchLocation of Vent Termination General Venting120V Electrical Hook Up There must not be any obstruction such as bushesGeneral Venting Information Termination Location Canadian Installations1 US Installations2Flex Vent Pipes Canadian InstallationsUSA Installations General Information Assembling Vent PipesExample B How to Use the Vent Graph36CDVXR Venting Example aStep Rear Wall Installation Twist Lock PipeSide view of final unit location Rear Wall Vent Application 7TCD45KTMaximum number of 90 elbows is three Vertical Sidewall ApplicationsMaximum number of elbows Vertical Sidewall Installation7TDVSNORK Below Grade InstallationVertical Through-the-Roof Applications Vertical Through-the-Roof InstallationPlace firestop spacers and secure Enlarged ends of the vent section always face down. FigCdvxt Top Vent Baffle 36CDVXT Vertical VentingVertical Sidewall Installations Vertical height requirement Always install horizontal venting on a level planeApply high temperature sealant to collars or termina- tions Below Grade InstallationsMax 3m Min 610 mm Venting Components Glass Information Glass CleaningWindow Frame Assembly Removal Operating InstructionsRN/RP & EN/EP Models Flame & Temperature AdjustmentFlame Characteristics LogsTo Turn Off Gas to Fireplace Lighting and Operating InstructionsLighting Instructions Turning Off the Gas to the ApplianceValve in the on position Troubleshooting the Gas Control System Pilot Conversion Fuel Conversion InstructionsTesting for Leaks Pilot Flame AdjustmentReassembly Maintenance Cleaning the Standing Pilot Control SystemBurner and Burner Compartment 6a,b 14a,b DescriptionFuel Conversion Kits CdvxFan Kits Optional Accessories AvailableWiring Instructions Remote ControlsCdvx Series Direct Vent Gas Fireplace Cdvx Series Direct Vent Gas Fireplace Cdvx Series Direct Vent Gas Fireplace Lifetime Warranty Five Year WarrantyBasic Warranty Fan-OFF Fan-ON Efficiency Ratings

36CDVXTRN specifications

The Monessen Hearth 36CDVXTRN is a distinguished choice in the world of gas fireplaces, seamlessly blending aesthetics with cutting-edge technology. Designed to provide ample warmth while enhancing the ambiance of any room, this unit embodies the perfect fusion of form and function.

At the heart of the Monessen Hearth 36CDVXTRN is its impressive 36-inch width, providing a generous viewing area for the mesmerizing flames. The glass front offers an unobstructed view, creating a stunning focal point in any living space. With a contemporary design and realistic log set, this fireplace captures the essence of a traditional wood-burning fire without the hassle of logs or ash cleanup.

One of the standout features of the 36CDVXTRN is its advanced burner technology. The fireplace utilizes a dual burner system to create a realistic flame that rises and dances, mimicking the natural motion of a wood fire. This not only adds to the aesthetic appeal but also ensures a consistent and efficient heat output. The unit boasts an exceptional heat output of up to 33,000 BTUs, making it suitable for heating larger areas while maintaining efficiency.

The Monessen Hearth 36CDVXTRN is engineered with user convenience in mind. It comes equipped with a remote control, allowing users to easily adjust settings from the comfort of their seat. The IntelliFire® ignition system adds another layer of convenience, offering a reliable and efficient ignition process. This innovative technology ensures safe operation and quick lighting, eliminating the need for matches or lighters.

Safety is a top priority with the Monessen Hearth 36CDVXTRN. The fireplace includes a sealed combustion chamber, preventing any harmful gases from entering the home. Additionally, the unit features a standard safety shut-off, which automatically turns off the gas supply in case of a malfunction, providing peace of mind for families.

Installation is straightforward with the Monessen Hearth 36CDVXTRN, as it is designed for either vented or vent-free configurations. This versatility allows homeowners to select the best option for their specific needs and preferences. Furthermore, the unit is compatible with various decorative options, from traditional mantels to modern finishes, allowing for complete customization to fit any interior style.

Overall, the Monessen Hearth 36CDVXTRN stands out as a premium gas fireplace solution, offering exceptional heat output, user-friendly features, and an elegant design. Its blend of modern technology and traditional aesthetics makes it an ideal choice for those looking to enhance their living space while enjoying the comforts of a captivating fire. Whether used for warmth or as a centerpiece of relaxation, the Monessen Hearth 36CDVXTRN is a testament to quality and sophistication in home heating solutions.
Top Page Image Contents