Monessen Hearth 36CDVXTRN installation instructions Below Grade Installation, 7TDVSNORK

Page 19

High

X

CDVX Series Direct Vent Gas Fireplace

Below Grade Installation

Temperature Sealant

 

 

CFM137

Fig. 32

Apply high temperature sealant.

 

 

X

X

 

 

CFM138

Fig. 33

Horizontal length requirement.

 

STEP 6

Support the horizontal pipes every 36” (914 mm) with metal pipe straps. Make sure that the horizontal vent pipe is installed on a level horizontal plane.

STEP 7

Re-check the fireplace to make sure that it is levelled, properly positioned, and nailed or screwed to the floor. If applied, the fireplaces adjustable frame drywall strips (nailing flanges) should be fastened. Refer to “Framing & Finishing”.

When it is not possible to meet the required vent ter- minal clearances of 12” (305 mm) above grade level a snorkel vent kit #7TDVSNORK is required. It allows installation depth of down to 7” (178 mm) below grade level. The 7” is measured from the center of the hori- zontal vent pipe as it penetrates through the wall.

If venting system is installed below ground, we recommend a window well with adequate and proper drainage.

Ensure sidewall venting clearances are observed.

The maximum horizontal run with 24” vertical rise is 36” (914 mm) from the back of the fireplace to the face of the exterior wall. See vent graph (Page 13) for extended horizontal run if the vertical rise exceeds 24” (610 mm).

1.Establish vent hole through the wall. (Fig. 17)

2.Remove soil to a depth of approximately 16” (406mm) below base of snorkel. Install window well (not supplied). Refill hole with 12” (305 mm) of coarse gravel leaving a clearance of approximately 4” (102 mm) below snorkel. (Fig. 34)

3.Install vent system. See Page 14, Steps 2 through 5.

4.Ensure a watertight seal is made around the vent pipe coming through the wall.

5.Apply high temperature sealant caulking around the 4” and 7” snorkel collars.

6.Slide into the vent pipe and secure to the wall.

7.Level the soil to maintain a 4” (102 mm) clearance below snorkel. (Fig. 34)

 

7TDVSNORK

 

(Snorkel)

Firestop

 

7” Pipe

4” (102mm)

 

Clearance

 

Min.

 

Window

24" (610mm)

Well

Minimum*

 

 

Gravel

 

Drain

 

Foundation Wall

 

*A minimum of 24” (608mm)

 

vertical pipe must be installed

 

when using 7TDVSNORK Kit.

 

BG400

Fig. 34 Below grade installation.

20012253

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Builder Direct Vent Models Table of Contents Certified To Installation & Operating InstructionsGas Equipment Venting System not Provided Requirements for the Commonwealth of MassachusettsFireplace specifications and framing dimensions Fireplace Dimensions Rear Vent1756 203 mm 435 mm 166 422 mm Fireplace Dimensions Top VentMantels Mantel ChartLocating Your Fireplace Clearance to CombustiblesFinal Finishing Hood InstallationHearth Framing and FinishingGas Inlet and Manifold Pressures Gas SpecificationsGas Line Installation Remote ON/OFF SwitchLocation of Vent Termination General Venting120V Electrical Hook Up There must not be any obstruction such as bushesGeneral Venting Information Termination Location Canadian Installations1 US Installations2Flex Vent Pipes Canadian InstallationsUSA Installations General Information Assembling Vent PipesExample B How to Use the Vent Graph36CDVXR Venting Example aStep Rear Wall Installation Twist Lock PipeSide view of final unit location Rear Wall Vent Application 7TCD45KTMaximum number of 90 elbows is three Vertical Sidewall ApplicationsMaximum number of elbows Vertical Sidewall Installation7TDVSNORK Below Grade InstallationVertical Through-the-Roof Applications Vertical Through-the-Roof InstallationPlace firestop spacers and secure Enlarged ends of the vent section always face down. FigCdvxt Top Vent Baffle 36CDVXT Vertical VentingVertical Sidewall Installations Vertical height requirement Always install horizontal venting on a level planeApply high temperature sealant to collars or termina- tions Below Grade InstallationsMax 3m Min 610 mm Venting Components Glass Information Glass CleaningWindow Frame Assembly Removal Operating InstructionsRN/RP & EN/EP Models Flame & Temperature AdjustmentFlame Characteristics LogsTo Turn Off Gas to Fireplace Lighting and Operating InstructionsTurning Off the Gas to the Appliance Lighting InstructionsValve in the on position Troubleshooting the Gas Control System Pilot Conversion Fuel Conversion InstructionsPilot Flame Adjustment Testing for LeaksReassembly Cleaning the Standing Pilot Control System MaintenanceBurner and Burner Compartment 6a,b 14a,b DescriptionFuel Conversion Kits CdvxFan Kits Optional Accessories AvailableWiring Instructions Remote ControlsCdvx Series Direct Vent Gas Fireplace Cdvx Series Direct Vent Gas Fireplace Cdvx Series Direct Vent Gas Fireplace Five Year Warranty Lifetime WarrantyBasic Warranty Fan-OFF Fan-ON Efficiency Ratings

36CDVXTRN specifications

The Monessen Hearth 36CDVXTRN is a distinguished choice in the world of gas fireplaces, seamlessly blending aesthetics with cutting-edge technology. Designed to provide ample warmth while enhancing the ambiance of any room, this unit embodies the perfect fusion of form and function.

At the heart of the Monessen Hearth 36CDVXTRN is its impressive 36-inch width, providing a generous viewing area for the mesmerizing flames. The glass front offers an unobstructed view, creating a stunning focal point in any living space. With a contemporary design and realistic log set, this fireplace captures the essence of a traditional wood-burning fire without the hassle of logs or ash cleanup.

One of the standout features of the 36CDVXTRN is its advanced burner technology. The fireplace utilizes a dual burner system to create a realistic flame that rises and dances, mimicking the natural motion of a wood fire. This not only adds to the aesthetic appeal but also ensures a consistent and efficient heat output. The unit boasts an exceptional heat output of up to 33,000 BTUs, making it suitable for heating larger areas while maintaining efficiency.

The Monessen Hearth 36CDVXTRN is engineered with user convenience in mind. It comes equipped with a remote control, allowing users to easily adjust settings from the comfort of their seat. The IntelliFire® ignition system adds another layer of convenience, offering a reliable and efficient ignition process. This innovative technology ensures safe operation and quick lighting, eliminating the need for matches or lighters.

Safety is a top priority with the Monessen Hearth 36CDVXTRN. The fireplace includes a sealed combustion chamber, preventing any harmful gases from entering the home. Additionally, the unit features a standard safety shut-off, which automatically turns off the gas supply in case of a malfunction, providing peace of mind for families.

Installation is straightforward with the Monessen Hearth 36CDVXTRN, as it is designed for either vented or vent-free configurations. This versatility allows homeowners to select the best option for their specific needs and preferences. Furthermore, the unit is compatible with various decorative options, from traditional mantels to modern finishes, allowing for complete customization to fit any interior style.

Overall, the Monessen Hearth 36CDVXTRN stands out as a premium gas fireplace solution, offering exceptional heat output, user-friendly features, and an elegant design. Its blend of modern technology and traditional aesthetics makes it an ideal choice for those looking to enhance their living space while enjoying the comforts of a captivating fire. Whether used for warmth or as a centerpiece of relaxation, the Monessen Hearth 36CDVXTRN is a testament to quality and sophistication in home heating solutions.
Top Page Image Contents