Monessen Hearth 36CDVXTRN Operating Instructions, Glass Information, Louvre Removal

Page 29

CDVX Series Direct Vent Gas Fireplace

Operating Instructions

Glass Information

Only glass approved by MHSC should be used on this fireplace.

The use of any non-approved replacement glass will void all product warranties.

Care must be taken to avoid breakage of the glass.

Do not operate appliance with glass front removed, cracked or broken.

Replacement glass (complete with gasket) is available through your MHSC dealer and should only be installed by a licensed qualified service person.

7!2.).'

(/4/',!33 7),,

#!53%5"52.3

$/ ./4 4/5#( ',!33

5.4),4#//,%$

.%6%2 !,,/77#(),$2%.

4/ 4/5#( ',!33

Louvre Removal

6.Tilt the window frame assembly out slightly at the bottom, lift the window frame assembly up and away from the fireplace.

7.To replace the window frame assembly reverse the procedure.

Lower Clamps

 

Window

 

Frame

Window

Assembly

 

Frame

Pull Clamp

Assembly

Hook

Push

Clamp

 

Handle

FP1228

 

Fig. 62 Window frame assembly removal.

Glass Cleaning

The top louvre panel is removed by lifting the panel vertically and pulling it away from the appliance. (Fig. 61) The lower access door is removed in the same manner.

2.

Louvre

1.

Glass Panel

FP1602

It is necessary to periodically clean glass. During start- up condensation, which is normal, forms on the inside of the glass. This condensation causes lint, dust and other airborne particles to cling to glass surface.

Also initial paint curing may deposit a slight film on the glass. It is therefore recommended the glass be cleaned two or three times with a non-ammonia based household cleaner and warm water (We recommend gas fireplace glass cleaner) within the first few weeks of operation.

After the initial cleaning process the glass should be

Fig. 61 Remove top louvre assembly.

Window Frame Assembly Removal

1.Turn the fireplace OFF (including the pilot)

2.If the unit has been operating allow time for the components to cool.

3.Remove the top louvre assembly.

4.Remove the lower louvre panel.

5.Release the two clamps securing the lower edge of the window frame assembly by pulling down on the handles. (Fig. 62)

cleaned two or three times during each operating season depending on the environment in the house.

Clean glass after first two weeks of operation.

Do not clean glass when hot.

Do not use abrasive cleaners.

Do not strike or slam the glass.

20012253

29

Image 29
Contents Builder Direct Vent Models Table of Contents Certified To Installation & Operating InstructionsGas Equipment Venting System not Provided Requirements for the Commonwealth of MassachusettsFireplace specifications and framing dimensions Fireplace Dimensions Rear Vent1756 203 mm 435 mm 166 422 mm Fireplace Dimensions Top VentLocating Your Fireplace Mantel ChartClearance to Combustibles MantelsHearth Hood InstallationFraming and Finishing Final FinishingGas Line Installation Gas SpecificationsRemote ON/OFF Switch Gas Inlet and Manifold Pressures120V Electrical Hook Up General VentingThere must not be any obstruction such as bushes Location of Vent TerminationGeneral Venting Information Termination Location Canadian Installations1 US Installations2USA Installations Canadian InstallationsGeneral Information Assembling Vent Pipes Flex Vent Pipes36CDVXR Venting How to Use the Vent GraphExample a Example BStep Rear Wall Installation Twist Lock PipeSide view of final unit location Rear Wall Vent Application 7TCD45KTMaximum number of 90 elbows is three Vertical Sidewall ApplicationsMaximum number of elbows Vertical Sidewall Installation7TDVSNORK Below Grade InstallationVertical Through-the-Roof Applications Vertical Through-the-Roof InstallationPlace firestop spacers and secure Enlarged ends of the vent section always face down. FigCdvxt Top Vent Baffle 36CDVXT Vertical VentingVertical Sidewall Installations Vertical height requirement Always install horizontal venting on a level planeApply high temperature sealant to collars or termina- tions Below Grade InstallationsMax 3m Min 610 mm Venting Components Window Frame Assembly Removal Glass CleaningOperating Instructions Glass InformationFlame Characteristics Flame & Temperature AdjustmentLogs RN/RP & EN/EP ModelsTo Turn Off Gas to Fireplace Lighting and Operating InstructionsValve in the on position Lighting InstructionsTurning Off the Gas to the Appliance Troubleshooting the Gas Control System Pilot Conversion Fuel Conversion InstructionsReassembly Testing for LeaksPilot Flame Adjustment Burner and Burner Compartment MaintenanceCleaning the Standing Pilot Control System 6a,b 14a,b DescriptionFuel Conversion Kits CdvxWiring Instructions Optional Accessories AvailableRemote Controls Fan KitsCdvx Series Direct Vent Gas Fireplace Cdvx Series Direct Vent Gas Fireplace Cdvx Series Direct Vent Gas Fireplace Basic Warranty Lifetime WarrantyFive Year Warranty Fan-OFF Fan-ON Efficiency Ratings

36CDVXTRN specifications

The Monessen Hearth 36CDVXTRN is a distinguished choice in the world of gas fireplaces, seamlessly blending aesthetics with cutting-edge technology. Designed to provide ample warmth while enhancing the ambiance of any room, this unit embodies the perfect fusion of form and function.

At the heart of the Monessen Hearth 36CDVXTRN is its impressive 36-inch width, providing a generous viewing area for the mesmerizing flames. The glass front offers an unobstructed view, creating a stunning focal point in any living space. With a contemporary design and realistic log set, this fireplace captures the essence of a traditional wood-burning fire without the hassle of logs or ash cleanup.

One of the standout features of the 36CDVXTRN is its advanced burner technology. The fireplace utilizes a dual burner system to create a realistic flame that rises and dances, mimicking the natural motion of a wood fire. This not only adds to the aesthetic appeal but also ensures a consistent and efficient heat output. The unit boasts an exceptional heat output of up to 33,000 BTUs, making it suitable for heating larger areas while maintaining efficiency.

The Monessen Hearth 36CDVXTRN is engineered with user convenience in mind. It comes equipped with a remote control, allowing users to easily adjust settings from the comfort of their seat. The IntelliFire® ignition system adds another layer of convenience, offering a reliable and efficient ignition process. This innovative technology ensures safe operation and quick lighting, eliminating the need for matches or lighters.

Safety is a top priority with the Monessen Hearth 36CDVXTRN. The fireplace includes a sealed combustion chamber, preventing any harmful gases from entering the home. Additionally, the unit features a standard safety shut-off, which automatically turns off the gas supply in case of a malfunction, providing peace of mind for families.

Installation is straightforward with the Monessen Hearth 36CDVXTRN, as it is designed for either vented or vent-free configurations. This versatility allows homeowners to select the best option for their specific needs and preferences. Furthermore, the unit is compatible with various decorative options, from traditional mantels to modern finishes, allowing for complete customization to fit any interior style.

Overall, the Monessen Hearth 36CDVXTRN stands out as a premium gas fireplace solution, offering exceptional heat output, user-friendly features, and an elegant design. Its blend of modern technology and traditional aesthetics makes it an ideal choice for those looking to enhance their living space while enjoying the comforts of a captivating fire. Whether used for warmth or as a centerpiece of relaxation, the Monessen Hearth 36CDVXTRN is a testament to quality and sophistication in home heating solutions.