Napoleon Fireplaces GDS28P manual GAS Installation, Optional Wall Switch / Thermostat / Remote

Page 25
If equipped with a flex connector the appliance is designed to accept a 1/2” gas supply. Without the connector it is designed to accept a 3/8” gas supply. The appliance is equipped with a manual shut off valve to turn off the gas supply to the appliance.
Connect the gas supply in accordance to local codes. In the absence of local codes, install to the current CAN/CSA-B149.1 Installation Code in Canada or to the current National Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the United States.
When flexing any gas line, support the gas valve so that the lines are not bent or kinked.
The gas line flex-connector should be installed to provide sufficient movement for shifting the burner assembly on it’s side to aid with servicing components.
Check for gas leaks by brushing on a soap and water solution.
30.1A

25

4.5GAS INSTALLATION

!WARNING

RISK OF FIRE, EXPLOSION OR ASPHYXIATION. ENSURE THERE ARE NO IGNITION SOURCES SUCH AS

SPARKS OR OPEN FLAMES.

SUPPORT GAS CONTROL WHEN ATTACHING GAS SUPPLY PIPE TO PREVENT DAMAGING GAS LINE.

ALWAYS LIGHT THE PILOT WHETHER FOR THE FIRST TIME OR IF THE GAS SUPPLY HAS RUN OUT WITH THE GLASS DOOR OPENED OR REMOVED. PURGING OF THE GAS SUPPLY LINE SHOULD BE PERFORMED BY A QUALIFIED SERVICE TECHNICIAN. ASSURE THAT A CONTINUOUS GAS FLOW IS AT THE BURNER BEFORE CLOSING THE DOOR. ENSURE ADEQUATE VENTILATION. FOR GAS AND ELECTRICAL LOCATIONS, SEE “DIMENSION” SECTION.

ALL GAS CONNECTIONS MUST BE CONTAINED WITHIN THE APPLIANCE WHEN COMPLETE.

HIGH PRESSURE WILL DAMAGE VALVE. DISCONNECT GAS SUPPLY PIPING BEFORE TESTING GAS

LINE AT TEST PRESSURES ABOVE 1/2 PSIG.

VALVE SETTINGS HAVE BEEN FACTORY SET, DO NOT CHANGE.

Installation and servicing to be done by a qualified installer. Do not use open flame.

4.5.1 Move the appliance into position and secure.

4.5.2

4.5.3

4.5.4

4.5.5

4.5.6

4.6OPTIONAL WALL SWITCH / THERMOSTAT / REMOTE

!WARNING

DO NOT CONNECT EITHER THE WALL SWITCH, THERMOSTAT OR GAS VALVE DIRECTLY TO 110

VOLT ELECTRICITY.

For ease of accessibility, an optional remote wall switch or millivolt thermostat may be installed in a convenient location. Route a 2 strand, solid core millivolt wire from the valve to the wall switch or millivolt thermostat. The recommended maximum lead length depends on wire size:

WIRE SIZE

MAX. LENGTH

3

14 gauge

100 feet

2

16 gauge

60 feet

18 gauge

40 feet

 

Disconnect the existing wires from terminals 1 and 3 (from the

1

ON/OFF switch) and replace with the leads from the wall switch / millivolt thermostat.

50.1

W415-0153 / B / 06.10.10

Image 25
Contents What to do if YOU Smell GAS Installation Operating InstructionsTable of Contents Installation Overview Introduction General Instructions DimensionsWe suggest that our gas GDS28 General InformationOutput CS280/GS28RENDEMENT Rating Plate InformationVenting Refer to the section applicable to your installationPart Supplier Website Venting Lengths and ComponentsMinimum Feet Maximum Typical Vent InstallationMinimum Plus RiseMinimum MIN. to Grade Special Vent Installations 3.3.1 Periscope TerminationMIN. to Grade Covered Balcony Applications †† Vent Terminal ClearancesDefinitions Venting Application Flow Chart TOP ExitElbow Vent Length Values Feet InchesHT VT Simple venting configuration only one 90 elbow TOP Exit Horizontal TerminationHT VT TOP Exit Vertical Termination Simple venting configurationsV T Pipe Vertical Through Existing ChimneyMinimum Clearances to Combustibles InstallationWall and Ceiling Protection Horizontal InstallationHorizontal AIR Terminal Installation Model GDS28 Vertical InstallationVertical AIR Terminal Installation High Temperature Sealant Mobile Home Installation Model GDS28Appliance Vent Connection Self DrillingOptional Wall Switch / Thermostat / Remote GAS InstallationWire Size MAX. Length Vent Specifics Chimney Installation Plates and Gasket Installing B VentAdding Vent Sections Combustion AIRDoor Closing and Opening FinishingLOG Placement Glowing Embers Logo PlacementCharcoal Embers Model GS28 only Venting Action Check OperationLighting Instructions OPERATING/LIGHTING InstructionsTo Turn OFF GAS Pilot Burner Adjustment AdjustmentVenturi Adjustment Restricting Vertical Vents Model GDS28 Flame CharacteristicsBurner Sensor Flame Must EnvelopCare of Glass MaintenanceBlower Replacement Common Components ReplacementsGS28 Components Common Accessories 51 52 46 45 Symptom Problem Trouble ShootingDo not Over Torque Symptom Problem Test SolutionGDS28 Conditions and Limitations WarrantyService History 44.1 44.1

GDS28P specifications

Napoleon Fireplaces has long been a respected name in the world of home heating, and the GDS28P model is a shining example of the brand's dedication to quality and efficiency. This direct vent gas stove is not only a stylish addition to any living space, but it also boasts a range of features and technologies that enhance both performance and user experience.

One of the standout features of the GDS28P is its compact yet powerful design. With a heat output of up to 20,000 BTUs, this stove is capable of warming areas up to 1,000 square feet. Its impressive heating capacity makes it ideal for use in a variety of home settings, whether in a cozy living room or as a supplementary heating source in a larger open floor plan.

The GDS28P incorporates Napoleon's advanced high-efficiency technology, which maximizes heat output while minimizing emissions. The unit features a dual burner system that allows for both a lively flame and a more subdued ambiance. The adjustable flame height and heat output provide homeowners with complete control over their heating experience, ensuring comfort throughout the colder months.

Another notable characteristic is the GDS28P's sleek design, which includes a large viewing area, allowing for an unobstructed view of the alluring flames. The stove is available in a range of finishes, making it easy to integrate into various decor styles. The large glass front allows users to enjoy the mesmerizing effect of the fire, while also ensuring that heat is efficiently radiated into the room.

Additionally, the GDS28P is equipped with a state-of-the-art electronic ignition system, providing reliable startup even in the coldest conditions. The built-in fan kit enhances air circulation, ensuring even heat distribution throughout any space. The unit can be operated via a remote control, allowing users to easily adjust settings while lounging comfortably.

For those concerned about the environment, the GDS28P exceeds the stringent guidelines set by the EPA, providing a cleaner burn compared to traditional wood stoves. This not only reduces your carbon footprint, but it also means less maintenance and cleaning.

In summary, the Napoleon Fireplaces GDS28P is a cutting-edge heating solution that combines efficiency, style, and user-friendly features. Its powerful heating capabilities, advanced technologies, and aesthetic appeal make it a valuable addition to any home, providing warmth and enhancing living spaces while safeguarding the environment.