Louisville Tin and Stove BFT302, BFT201, BFT301, BFT102, BFT202, BFT101 warranty Installation, Location

Page 5

FRESH AIR FOR COMBUSTION, VENTILATION AND HEAT DISTRIBUTION - CONT’D.

STEP 4. Compare the total Btu the area can support (from Step 2) to the total Btu in the area the heater will be installed (from Step 3). If the total from Step 2 is larger this is considered an unconfined space, if Btu total from Step 3 is larger this is considered a confined space and provisions must be made for additional combustion and ventilation air. EXAMPLE: Btu area can support is 56,250, total Btu in area is 106,000 – this would be a confined space.

NOTE: A third construction class is one with unusually tight construction, defined as, construction where: (A) Walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder with a rating of 1 per (6x10-11 Kg per pa-sec-m²) or less with openings gasketed or sealed, and, (B) Weatherstripping has been added enable windows and doors, and , (C) Caulking or sealants are applied to areas such as joints around window and door frames, between sole plates and floors, between wall ceiling joints, between wall panels, at penetration for plumbing, electrical, and gas lines, and at other openings.

“WARNING: If the area in which the heater may be operated is smaller than that defined as an unconfined space, or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of the methods described in the National Fuel Gas Code, ANSI Z223.1, Section 5.3 or applicable local codes.” Examples would be to provide two permanent openings either to an adjoining room, or to the outside. See the National Fuel Gas Code for details. See Figure 9 & Figure 10 below.

Chimney or gas vent

Opening

Furnace Water

Heater

Opening

Equipment located in confined spaces; all air from inside the building. See 5.3.3(a).

Chimney or gas vent

Ventilation louvers (each end of attic)

 

Outlet Air

Furnace Water

Inlet Air

Heater

Alternate air inlet

Ventilation louvers for unheated crawl space

Equipment located in confined spaces; all air from outdoors - inlet air from ventilated crawl space and outlet air to ventilated attic. See 5.3.3(b).

FIGURE 9

FIGURE 10

INSTALLATION

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

LOCATION

1)For most efficient performance, locate heater as centrally as possible in the area to be heated.

2)Do not install heater in a closet, alcove or small hallway where the heater could be isolated from the space to be heated and adequate combustion air by closing a door.

Page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents What to do if YOU Smell GAS Blue Flame Vent Free HeatersIllustrated Parts BREAKDOWN……… Tools & Additional SUPPLIES… IntroductionSafety Instructions Room Heater SpecificationsIntroduction CONT’D OperationFresh AIR for COMBUSTION, Ventilation and Heat Distribution Location InstallationTools and Additional Supplies Required ClearancesFeet Pipe Length NA GasturalPropane GAS Wall Mount Installing Heater Wall Mount BFT10Installing VF-FSK Floor Base KIT Burner Orifice GAS ConnectionSpecific Elevation Natural GASFor Your Safety Read Before Lighting Proper Operation ODS / Pilot Flame Cabinet MaintenanceMain Burner ODS/PILOTBlower Instructions Symptom Possible Causes Corrective Action Trouble Shooting GuideBFT101 BFT102 BFT201 BFT202 BFT301 BFT302 Model Included NAT. GAS L.P. GASModel Numbers NAT Tampering is Dangerous Critical Safety Points to RememberTable a Limited Warranty

BFT301, BFT302, BFT102, BFT201, BFT202 specifications

Louisville Tin and Stove has established itself as a reputable name in the world of heating solutions, offering a range of innovative products designed for both efficiency and comfort. Among their notable offerings are the BFT101, BFT302, BFT201, BFT102, and BFT202 models. Each of these units boasts unique features, technologies, and characteristics that cater to various customer needs.

The BFT101 is designed with compact living spaces in mind. It offers an intuitive user interface that ensures easy operation. Its efficient heat exchange system allows for rapid heating, providing warm air quickly and effectively. The BFT101's sleek design fits seamlessly into any room, making it an aesthetic addition to home décor while ensuring functionality.

The BFT302 takes efficiency a notch higher with advanced thermal technology. This model is equipped with a dual-fuel capability, allowing users to switch between different energy sources, such as gas or electric. The BFT302's smart thermostat provides precise temperature control, optimizing energy consumption without compromising comfort. Additionally, it comes with a built-in safety mechanism that ensures the unit operates seamlessly and safely.

For larger spaces, the BFT201 model stands out with its powerful heating capabilities. This unit features a robust construction designed to withstand prolonged usage while delivering consistent heat throughout the area. The BFT201 is also compatible with smart home technology, allowing users to control the heating remotely, a feature that provides convenience and enhances user experience.

The BFT102 is favored for its versatility. It operates efficiently in various environments, whether it’s a residential setting or a commercial space. Equipped with multiple heating settings, the BFT102 can easily adapt to changing temperature needs. Its low emissions make it an eco-friendly choice, aligning with sustainability goals without sacrificing performance.

Lastly, the BFT202 offers a combination of elegance and innovation. This model is equipped with advanced filtration technology that not only heats efficiently but also cleans the air, ensuring a healthier environment. The BFT202 features a whisper-quiet operation, making it suitable for bedrooms and offices where noise reduction is important.

In summary, the Louisville Tin and Stove BFT series, including the BFT101, BFT302, BFT201, BFT102, and BFT202, provides a comprehensive range of heating solutions that cater to a variety of spaces and customer preferences. Each model is designed with state-of-the-art technology, focusing on energy efficiency, safety, and user convenience, making them excellent choices for modern heating needs.
Top Page Image Contents