Harman Stove Company R16 manual #6 Installing into an existing chimney US and Canada

Page 13

Venting

#5 Installing into an existing fireplace chimney (US and Canada)

This method can be done with or without a flue liner. Without a liner, the damper area must be sealed off with a steel plate. Kaowool, mineral wool or an equivalent non-combustible insulation is recommended on top of the steel plate to minimize condensation. In this method a cap should also be installed on the chimney to keep out rain.

Some places in the US and Canada require that the vent pipe extend all the way to the top of the chimney. Per ULC S628.

Be sure to use approved pellet vent pipe fittings. Seal pipe joints with silicone or aluminum tape in addition to the sealing system used by the manufacturer. Pipe size should be increased to 4" using this method.

WARNING

The Chimney and Connector Must be

Maintained in Good Condition and

Kept Clean

Fig. 14

#6 Installing into an existing chimney (US and Canada)

This method provides excellent venting for normal operation. This method also provides natural draft in the event of a power failure.

In this method a 4 inch liner is installed the entire length of the flue. Whether using a rigid or flexible liner, a cap should be installed on the chimney to keep out rain.

*All joints for connector pipe must be secured with a minimum of three screws.

Chimney must be of a type suitable for solid fuel burning.

Fig. 15

XXV Pellet Stove 13

Image 13
Contents R16 Installation & Operating ManualPage Fuel and Fuel Storage Fuel SpecificationsSerial # Appliance Certification IntroductionModel Important Notes Assembly and InstallationFloor Protection InstallationAddition, the following must be observed VentingApplies Venting Do not connect to any air distribution duct or systemVent Pipe Direct Vent Wall Passthrough Avoiding Smoke and Odors#2 Preferred method #1 Preferred method#3 Installing into an existing chimney #6 Installing into an existing chimney US and Canada #8 Installing through the ceiling Vent Configurations Minimum flue vent configurationESP Control Blinks In Igniter Auto. Mode Only Indicates thatLow Draft Voltage Adjustment Low Draft Voltage AdjustmentAutomatic IGNITION/OPERATION Room Temperature ModeFeed Adjuster Knob Stove Temperature ModeShut Down Procedure Automatic Start UP Turn Feed Adjuster to #4.4Stove Temperature Mode Room Temperature ModeManual IGNITION/Operation Manual Start UP Igniter Switch to Manual up positionFill the hopper with pellets and remove ashes as required.1 Room sensor Installation Room Sensor InstallationCleaning MaintenanceRemoving Ashes ESP Burn Pot Cleaning and Maintenance Maintenance Burn PotNot coiled inside the burn pot Viewing Glass XXV Top Flue Option OptionsDirect Vent Wall Passthrough HarmanCleaning Burn Pot Trouble-ShootingHelpful Hints FuelWiring Diagram SpecificationsXXV Pellet Stove Hearth & Home Technologies Inc Limited Lifetime WarrantyThis warranty is void if Warranty ConditionsOperation in Room Temp mode Operation in Stove Temp modeChanges to Maintenance Schedule Active Service PartsRetired units Part number list on followingStocked At depotNo longer available Stocked at depotXXV Pellet Stove Stocked #44 Feeder assembly Post Serial numberHardware Packages Service & Maintenance Log Service & Maintenance Log Page Proudly Printed On 100% Recycled Paper Signature of Boxer

R16 specifications

The Harman Stove Company R16 is a testament to innovative design and efficiency in the world of heating solutions. Built to provide both comfort and style, this stove stands out with its blend of traditional appeal and modern technology.

One of the key features of the R16 is its impressive heating capacity. It is designed to effectively warm up medium to large spaces, making it an ideal choice for homes and cabins alike. With a high BTU output, the R16 optimizes fuel use while distributing heat uniformly, ensuring the entire area remains cozy even in the coldest months.

Another highlight of the R16 is its advanced combustion technology. The stove incorporates a clean-burning system that not only maximizes efficiency but also reduces emissions. This environmentally friendly approach aligns with the growing commitment to sustainability in heating solutions. The R16 can burn a variety of fuels, including wood, making it versatile and convenient for different users.

The design of the R16 also supports ease of use and maintenance. It features a user-friendly control panel, allowing owners to adjust settings effortlessly. Additionally, the stove is equipped with a large glass door, providing an unobstructed view of the flames and enhancing the ambiance of any room.

Durability is another characteristic of the R16. Constructed with high-quality materials, this stove is built to last. The cast iron body ensures excellent heat retention, while the elegant finish complements a variety of interior styles.

Safety is paramount in the design of the Harman R16. It comes with built-in safety features, including a heat shield and an effective flue system that minimizes the risk of overheating and ensures safe operation.

In conclusion, the Harman Stove Company R16 combines cutting-edge technology, efficiency, and aesthetic appeal. With its powerful heating capabilities, clean combustion system, ease of use, and robust design, it stands out as a leading choice for those seeking a reliable and stylish heating solution for their spaces. The R16 not only provides warmth but also enhances the overall experience of a home, making it a worthy investment for any homeowner.