Empire Comfort Systems DVP42FP, P)-2 RF Transmitter Functions, Status Action

Page 59

RF TRANSMITTER FUNCTIONS

FIRST USE OF TRANSMITTER

Status

 

Action

 

 

 

Begin communication between transmitter and receiver/valve.

 

Move LOCAL/REMOTE Switch to LOCAL position for at least two

 

 

seconds; then move switch to the REMOTE position.

 

 

 

Transmit unique code.

 

Press Fan or Flame key within 30 seconds.

 

 

 

Confirm recognition between transmitter and receiver/valve.

 

Observe LED turns on for one second.

 

 

 

Chose Remote or Local operation.

 

Move LOCAL/REMOTE switch to LOCAL or leave in REMOTE.

 

 

 

Operation in the Remote Position

AUTO Mode

With the control in the AUTO mode, the flame in the main burner will turn on, off, or change height based on the heat needed to maintain the set temperature.

Status

Set to AUTO.

Change set temperature.

Flame.

Fan.

To Set Delay Timer.

Action

Press MODE button until mode is AUTO.

Press UP or DOWN key to change set temperature.

Automatically changes.

Automatically changes.

Press TIME key followed by either an UP or DOWN arrow key.

CAUTION

Properly Damage Hazard.

Excessive heat can cause property damage.

In AUTO mode, the main burner will cycle indefinitely to maintain the set temperature. Keep the transmitter in a heated living space to make sure that the main burner is not on continuously.

On Mode

When the control is in the ON mode, the flame and fan levels and the delay timer are changed with the UP and DOWN arrow keys.

Status

 

Action

Set to ON.

 

Press MODE button until mode is ON.

 

 

 

Flame.

 

Press FLAME button and press UP or DOWN arrow key to change flame

 

 

height.

 

 

 

Fan.

 

Press FAN button and press UP or DOWN arrow key to change fan speed.

 

 

 

Delay Time.

 

Press DELAY TIMER button and press UP or DOWN key to change timer.

 

 

 

OFF Mode

 

Press MODE until mode is OFF.

The flame in the main burner will turn off and the room temperature

 

 

will be displayed in the remote window.

 

 

 

 

 

Operation in the LOCAL Mode.

 

NOTE: Remote/Local switch on the receiver/valve must be in the LOCAL position.

 

 

 

FAN

 

In LOCAL mode, to turn flame on/off, rotate manual knob from ON to

Flame height and fan speed both go to the highest position.

 

PILOT position.

 

 

 

Other Functions:

 

 

 

Change between Fahrenheit and Celsius temperature units.

 

Press UP and DOWN arrow keys at the same time and hold for at least

 

 

three seconds.

 

 

 

Fan Override during AUTO Mode.

 

Press FAN button, and press UP or DOWN arrow key to change the fan

 

 

speed.

 

 

 

Disable thermostat function in the AUTO Mode

 

Press the TIME, DOWN and FLAME arrow keys at the same time and hold

 

 

for at least three seconds.

 

 

 

21759-6-0608

Page 59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents UL File NO. MH30033 Millivolt Standing PilotIntermittent Pilot Remote RF ModelsTable of Contents Important Safety Information Some Points to Remember LP-GAS Warning OdorNo Odor Detected Odor Fade Vent Directly BELOW. Keep Clear of ALL Obstructions Requirements for MassachusettsIntroduction DVP42 DVP48 SpecificationsFireplace Dimensions Remote Control Options DescriptionCombustible Material ClearancesLocating Fireplace Clearances FigureChecking Manifold Pressures Installing a New Main Gas CockGAS Supply Converting flue take-off to rear venting Rear Vent ConversionVent Pipe Clearance InstallationFraming and Finishing Finishing Figures 12 Flush Mount Mantel Installation FigureFraming Figure VERTICAL, 90 Elbow with Horizontal Termination Flush Wall InstallationCombustible Surround Installation Vent Runs Figures 14, 15, 16, 17Model VERTICAL, 90 Elbow to Horizontal OUT the WallExample B Venting Fireplace TOPTo Use the Vent Graph Figure Example aTypical Basement Installation Below Grade InstallationCutting the Hole Figures Positioning the FireplaceExamples TOP Vent RUN Vertically Off Top of Fireplace Only Venting Examples When Using DVA47 AdaptorDVVK-4FV Direct Vent Termination KIT Installation InstructionsBefore You Start Items Required For Installation Tools Building SuppliesInstallation of the Vertical Flex Termination Kit Installation NoteStep-By-Step Installation For Flex DV Kit Roof Pitch DIA. Flex AIR Intake Pipe 35 ft. Max Number Item Description Repair Part No Supplied QuantityVenting Fireplace Rear Dimensions in FeetExamples Rear Vent RUN Parts Verification DVVK-4RE Vent KIT Installation InstructionsInstalling Wall Thimble/Firestop Assembly Sealing 4 102mm Diameter Flue Outlet Tube DVVK-4RE Vent KIT Installation InstructionsConnecting to Rigid Vent System Parts ListDVVK-4F Flex Vent Instructions TOP Vent only InstallationInformation on Various Venting Routes and Components Vertical Sidewall InstallationsTermination Clearances Vent Clearances Special Venting Components Simpson Duravent Vent System IdentificationDVVK-5RP Installing Vent Components FigureVenting Framing and Finishing Installing Support Brackets FigureSee Horizontal Termination Page 41 and Vertical Termination ⅝ Venting Framing and Finishing Installing Firestops Figures 64, 65, 66⅝ Venting Framing and Finishing Horizontal Termination DVVK-5F Flex Vent Instructions InstallationDetermining Minimum Vent Height Above the Roof General MaintenanceSee Figure Installing the Vent System in a Chase Vertical TerminationVertical Termination Reassembly and Resealing Vent Pipe SystemLOG Placement 4 LOG SET Pilot Flame Figure Operating InstructionsMillivolt System Initial LightingTRW Standing Pilot Wiring Diagram To Turn OFF GAS to Fireplace For Your SAFETY, Read Before LightingStanding Pilot Lighting Instructions Lighting InstructionsGlass soots Standing Pilot TroubleshootingFrequent pilot outage problem Pilot and main burner extinguish while in operationElectrical Connection Figure Intermittent Pilot Wiring DiagramIntermittent Pilot Operating Instructions Damage, personal injury or loss of life Intermittent Pilot Lighting InstructionsTo Turn OFF GAS to Appliance Operation Intermittent Pilot TroubleshootingS8600H Intermittent Ignition Module Specifications CheckoutMain Burner Operation Safety LockoutARC Length Action Ignition System Checks Check ignition cable. Make sureIntermittent Pilot Troubleshooting Green LED Status Codes RF Standing Pilot Operating Instructions Status Action RF Transmitter FunctionsRF Wiring Diagram Wiring Diagram with BlowerWhat to do if YOU Smell GAS For Your Safety Read Before LightingRF Standing Pilot Lighting Instructions Maintenance and Service Parts View Index Part Number Description DVP42 DVP48 Parts ListParts List Blower Wheels FBB4 Optional Variable Speed Blower InstallationBlower Motor Volt AC Optional Brick Liner Installation Instructions Junction BOX Wiring Installation InstructionsFBB4 AccessoriesService Notes HOW to Order Repair Parts Service Notes

DVP42FP, P)-2 specifications

Empire Comfort Systems has established itself as a leader in the heating and venting industry, providing innovative solutions that cater to modern home heating needs. One of their standout products is the Empire Comfort Systems DVP42FP,P)-2, a direct vent gas fireplace that seamlessly combines aesthetics, efficiency, and technology.

At the heart of the DVP42FP,P)-2 is its contemporary design, which enhances the ambiance of any living space. With a sleek glass front and a range of stylish finishes, this fireplace serves as a perfect centerpiece, embodying both function and fashion. The generous viewing area allows for an unobstructed view of the mesmerizing flames, creating a cozy atmosphere in any room.

This fireplace is engineered for efficiency and performance. With an impressive heating output, the DVP42FP,P)-2 can effectively warm spaces while consuming minimal fuel. It boasts a high-efficiency rating, ensuring that homeowners can enjoy the warmth without incurring high energy costs. The direct vent technology allows for a sealed combustion system that draws air from outside while expelling exhaust gases directly outdoors. This ensures that the air quality inside the home is maintained while providing optimal heating performance.

Ease of use is another hallmark of the DVP42FP,P)-2. It features an intuitive remote control system, allowing users to adjust the temperature and flame settings conveniently from anywhere in the room. This level of user-friendly control enhances the overall experience, making it easy to create the perfect environment.

Another notable characteristic of this model is its safety features. Equipped with safety screens and an auto shut-off feature, the DVP42FP,P)-2 is designed to offer peace of mind, allowing families to enjoy their fireplace without worries about safety.

Maintenance is straightforward with the DVP42FP,P)-2, thanks to its accessible design. Regular upkeep is minimal, allowing homeowners to spend more time enjoying the warmth and beauty of their fireplace rather than worrying about system maintenance.

In conclusion, the Empire Comfort Systems DVP42FP,P)-2 is a captivating, efficient, and technologically advanced direct vent gas fireplace. With its modern design, high efficiency, user-friendly controls, and robust safety features, it represents a wise investment for anyone looking to enhance their home's comfort and aesthetic appeal. Whether for a new build or a renovation, this fireplace stands out as a premier choice for discerning homeowners.
Top Page Image Contents