Qualiﬁed Installing Agency

Installation and replacement of gas piping, gas utilization equipment or accessories and repair and servicing of equipment shall be performed only by a qualiﬁed agency. The term "qualiﬁed agency" means any individual, ﬁrm, corporation or company which either in person or through a representative is engaged in and is responsible for (a) the installation or replacement of gas piping or (b) the connection, installation, repair or servicing of equipment, who is experienced in such work, familiar with all precautions required and has complied with all the requirements of the authority having jurisdiction.

The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54* Natural and Propane Installation Code, CSA B149.1.

*Available from the American National Standards Institute, Inc., 11 West 42nd St., New York, N.Y. 10036.

Clearances

1.In selecting a location forinstallation, it is necessary to provideadequate accessibility clearances for servicing and proper installation.

2.The FAW-40 can be attached to the wall or recessed into the wall up to 9 1/2 inches (24.1cm) in depth. Note: Do not place combustible header or material on top of unit when installed in wall. Maintain 3/4" minimum spacing above heater.

3.The wall in which the furnace is recessed has (0) zero (0mm) clearance to the furnace sides.

4.When using side discharge registers, SOR-1 or SOK-1, the furnace cannot be recessed into the wall.

5.Clearance to sidewall or combustible material is 4 inches (10.2cm).

6.Ceiling clearance is 4 inches (10.2cm).

7.Floor and rear wall clearance is (0) zero inches (0mm).

8.Clearance of 18 inches (46cm) is required to adjacent wall or combustible material when ﬂush mounted SOR-1, side outlet register is used.

Before Installing Consider The Following Venting

1.A chimney for residential-type or low-heat gas utilization equipment shall extend at least 3 feet (914mm) above the highest point where it passes through a roof of a building and at least 2 feet (610mm) higher than any portion of building within a horizontal distance of 10 feet (3m).

2.This furnace must not be connected to a chimney ﬂue serving a separate solid-fuel burning appliance.

3.Uninsulated Single-Wall Metal Pipe shall not be used outdoors in cold climates for venting gas utilization equipment.

4.Attention! This Fan Type Vented Wall Furnace is equipped with a vent safety switch. In the event of spillage of ﬂue products due to improper venting the vent safety switch will open, which results in the main burners to "shut off".

Model No. FAW-40 may be vented as shown in Figure 4. The vent cap termination must be at least 12 feet (3.7m) above the ﬂoor and must exhaust to the outdoors.. Clearance to combustible construction is held by the ﬁxed spacers at 1 inch (25mm) with B-1 or (B-W) vent pipe. Installation must conform to local codes.

A.4" (102mm) Round (all parts purchase locally except Item 2)

1.Type B-1 round pipe

2.Part No. DV-648, 4" (102mm) oval-to-round ﬂue adapter kit (see accessories)

3.Single story type B-1 gas vents require a baseplate and one pair of ceiling plate spacers.

4.Multi-story type B-1 gas vents require a baseplate, one pair of ceiling plate spacers at the ﬁrst ﬂoor ceiling and one pair of ﬁre stop spacers at each successive ceiling level.

B.4" (102mm) Oval (all parts purchase locally)

1.Type B-1 oval pipe or B-W vent pipe

2.Single story type B-1 or (B-W) gas vents require a baseplate and one pair of ceiling plate spacers.

3.Multi-story type B-1 or (B-W) gas vents require a baseplate, one pair of ceiling plate spacers at the ﬁrst ﬂoor ceiling and one pair of ﬁre stop spacers at each successive ceiling level.

12427-4-0306

C.4" (102mm) Oval In-The-Wall (all parts purchase locally)

1.Type B-1 oval pipe or B-W vent pipe

2.Type B-1 oval elbows or B-W oval elbows

3.Single story type B-1 or (B-W) gas vents require a baseplate and one pair of ceiling plate spacers.

4.Multi-story type B-1 or (B-W) gas vents require a baseplate, one pair of ceiling plate spacers at the ﬁrst ﬂoor ceiling and one pair of ﬁre stop spacers at each successive ceiling level.

Stud space around gas vents must be free of obstructions and building paper.

4” ROUND

VENT

ENCLOSURE

ADAPTER

WALL

BASEPLATE

SIDEFRONT

4” B-1 OVAL

BRACKET

BASEPLATE

	4” B-1 OVAL
4” 45 DEG.
OVAL ELBOWS	SPACER
	SPACER

BASEPLATE

4” B-1 OVAL

SPACER

BASEPLATE

Figure 4

Page 5

FAW-40-1IP, FAW-40-1SPP specifications

Empire Products has established itself as a leader in the manufacturing of high-quality heating solutions, and among its standout offerings are the FAW-40-1SPP and FAW-40-1IP models. These heaters have been engineered to meet the demands of various environments, providing efficient heating solutions while prioritizing user convenience and energy efficiency.

The FAW-40-1SPP is a powerful unit designed for versatile applications, whether in residential or commercial settings. This model boasts a robust output that ensures rapid heating even in larger spaces. Its advanced control system allows users to easily adjust the temperature settings, ensuring that comfort is maintained regardless of external weather conditions. This model is also equipped with safety features, including overheat protection, which automatically shuts off the heater if it reaches an unsafe temperature, a crucial feature for maintaining safety in populated areas.

On the other hand, the FAW-40-1IP represents innovation with its integrated programmable features. This unit is specifically designed for more tech-savvy users looking for convenience. The programmable thermostat enables users to set heating schedules, allowing for automated adjustments based on their daily routines. This not only enhances user comfort but also contributes to energy savings by avoiding unnecessary heating when spaces are unoccupied. Moreover, this model’s sleek design integrates seamlessly into modern interiors while providing durable performance.

Both models feature advanced heating technologies, including electric resistance heating, which provides immediate warmth and evenly distributes heat throughout the space. The utilization of high-grade materials ensures durability, making these models resistant to wear and tear, prolonging their lifespan.

In terms of ease of installation, Empire Products has made these units user-friendly, ensuring that both models can be set up with minimal hassle, appealing to DIY enthusiasts as well as professional installers. The compact designs of the FAW-40-1SPP and FAW-40-1IP also offer flexibility in placement, allowing users to position them in areas where they are needed most without taking up excessive space.

In conclusion, Empire Products’ FAW-40-1SPP and FAW-40-1IP heaters exemplify the balance between utility and innovation. With their array of features, user-friendly controls, and advanced heating technologies, these models are perfect for those seeking reliable and efficient heating solutions in various settings. Whether for a cozy home environment or a bustling commercial space, these heaters stand out as prime examples of quality and performance in the industry.