Empire Products DVC-35IPT-1, DVC-35T-1 Locating Electric Supply, Attaching Furnace to Wall

Page 10

Locating Electric Supply

A 7/8” diameter knockout is provided at the bottom of the left and right side panels. A three-prong (grounding) plug assembly is located within the control compartment (bottom) of the furnace. Please remove 7/8” knockout from appropriate side panel when routing plug assembly to an electrical outlet. Unit can be hard wired when recessed. Remove the 3 prong plug assembly and terminate inside the unit junction box.

Figure 7

Installation of Three-prong (Grounding) Plug Assembly

1.Disconnect nylon cap on 3’ plug assembly from nylon plug on wiring harness. Remove 3’ plug assembly from control compartment (bottom) of the furnace.

2.Remove 7/8” knockout from appropriate side panel.

3.Insert nylon cap on 3’ plug assembly into the 7/8” hole in the side panel.

4.Connect nylon cap on 3’ plug assembly to nylon plug on the wiring harness.

5.Place 7/8” strain relief bushing around the cord of the 3’ plug assembly. Insert 7/8” strain relief bushing into the 7/8” hole in the side panel.

Attention! The 7/8” strain relief bushing is located within the same envelope as the Installation Instructions and Owner’s Manual.

Attaching Furnace to Wall

Place collar on four inch flue tube against outlet box.Align clearance holes on collar with screw holes in outlet box. Attach four inch flue tube to outlet box with four (4) 10 x 1/2” screws.

Attention: Do not overtighten screws because outlet box must be able to move as flue tube expands and contracts.

Place collar on six inch air tube against air drop. Align clearance holes on collar with screw holes in air drop. Attach six inch air tube to air drop with eight (8) 10 x 1/2” screws.

Refer to Figure 5 for the location of the 7 1/2” diameter wall open- ing for the furnace. After the wall opening has been located and cut, position flue outlet on furnace in center of wall opening. Insert tubes through wall opening. When attaching furnace to the wall remove that portion of baseboard and molding on the wall which is behind the furnace. Attach furnace to wall, at the outer casing top,

Page 10

with two (2) plastic expansion anchors provided and to floor, at the outer casing bottom, with two (2) 10 x 1 1/2” screws provided.

Figure 8

Using Plastic Expansion Anchors

1.After locating mounting holes, drill two (2) 5/16” diameter holes into the wall.

2.Insert two (2) plastic expansion anchors provided into the holes.

3.Tighten two (2) 10 x 1” screws provided into the plastic expansion anchors. (See Figure 9)

Figure 9

Attention! The screw holes on the outer casing bottom are off-set the floor approximately 3/8”. Do not over-tighten screws and dis- tort the off-set on the outer casing bottom. Distortion of the outer casing bottom will not allow the lower front panel to be attached to the furnace.

13119-6-0107

Image 10
Contents Installation Instructions Table of Contents Important Safety Information Vent KIT InformationHave any question about the gas odor, call your LP-gas Safety Information for Users of LP-GASLearn to recognize the odor of LP-gas. Your local LP-Gas Measure under any conditionRequirements for Massachusetts Clear of ALL ObstructionsSpecifications IntroductionLocating Gas Supply Installing a New Main Gas CockGAS Supply Recommended Gas Pipe DiameterChecking Manifold Pressure ClearancesClearances Installing Optional Side Outlets Installation InstructionsLocating Wall Opening Locating Electric Supply Installation of Three-prong Grounding Plug AssemblyUsing Plastic Expansion Anchors Attaching Furnace to WallInstalling Vent Assembly Reassembly And Resealing Vent-Air Intake SystemFor Your Safety Read Before Lighting DVC-35T Standing Pilot Lighting InstructionsFor Your Safety Read Before Operating Pilot Flame Adjustment Pilot Flame CharacteristicsIP-Model Pilot Thermostat Installation Main Burner Flame CharacteristicsWiring DVC-35TLadder Wiring DIAGRAM-IP Valve Service and Maintenance Suggestions DVC-35IPT Intermittent Pilot Sequence of Operation DVC-35IPT Intermittent Pilot System Troubleshooting Sequence HOW to Order Repair Parts Parts ListParts View Service Notes Service Notes 13119-6-0107

DVC-35T-1, DVC-35IPT-1 specifications

Empire Products has long been recognized for its commitment to delivering high-quality heating solutions, and two notable offerings are the DVC-35T-1 and DVC-35IPT-1 gas-burning direct vent fireplaces. These units are designed to provide both comfort and aesthetic appeal, making them excellent choices for any home environment.

The DVC-35T-1 model boasts a classic design, paired with modern efficiency. With a heat output of 35,000 BTUs, it effectively warms spaces up to 1,100 square feet, ensuring even heat distribution throughout the room. One of the standout features is its advanced venting system, which allows for horizontal or vertical venting options, making it versatile for different installation layouts. The DVC-35T-1 also comes equipped with an adjustable flame control, enabling users to customize the ambiance to their preference. Its glass viewing area enhances the overall aesthetic while providing a full view of the flames.

On the other hand, the DVC-35IPT-1 model features an innovative design that incorporates a premium fireplace insert. This unit is specifically engineered to fit into existing fireplaces, transforming traditional wood-burning setups into efficient gas-burning heating sources. Like its counterpart, the DVC-35IPT-1 offers a maximum heat output of 35,000 BTUs, providing substantial warmth tailored for spaces up to 1,100 square feet. It is equipped with a state-of-the-art electronic ignition system, which ensures reliable and easy starts every time. The unit also includes a decorative log set that adds to its realism and charm, allowing for a cozy, inviting atmosphere.

Both models prioritize efficiency, with an impressive thermal efficiency rating, which not only helps in reducing heating costs but also makes them environmentally friendly options. The incorporation of a sealed combustion system ensures that indoor air quality is maintained, as it draws outside air for combustion and expels exhaust gases outdoors.

In addition to their technical features, the DVC-35T-1 and DVC-35IPT-1 are designed with user convenience in mind. Remote control capabilities allow for effortless operation, while easy maintenance ensures that homeowners spend less time worrying about upkeep and more time enjoying their fireplaces.

Overall, the Empire Products DVC-35T-1 and DVC-35IPT-1 fireplaces represent a blend of efficiency, technology, and aesthetic appeal, making them ideal options for those looking to enhance their home environment with reliable and stylish heating solutions.