Trane Model 012 GEH, 120 GEH Blower Motor 1/2 to 5 ton, Blower Motor 6 to 20 ton, Blower Housing

Page 14

R

Features and Benefits

Blower Motor: 1/2 to 5 ton

The supply-air (blower) motor is a multi-speed motor with internal ther- mal overload protection. The motor bearings are permanently lubricated and sealed.

All motors are factory wired to the option selected. A high, medium, and low speed tap is provided for field cus- tomization on most voltages. The speed tap modification can be made in the control box of the unit. See Figure 15 for blower motor.

Note: The three-phase designs are pro- vided in a dual or three-speed version only. See fan performance section for factory ratings.

Serviceability to the motor is made through either of the two air-side access doors for the horizontal configu- ration, and through one air-side access door on vertical configuration. The motor and blower wheel are removable by an orifice ring mounted to the fan housing.

Blower Motor: 6 to 20 ton

A belt driven motor selection powers the fan for the 6 through 20 ton dual circuit units. The 6 through 12-1/2 ton units include a single fan assembly. The 15 and 20-ton units include dual fan assemblies. Because the motor sheave and the motor base are adjustable in the field, a greater variation in external static pressures are available.

The large tonnage units are capable of providing 0 ESP to 3.0 ESP allowing a higher static ductwork to be applied on the mechanical system when the appli- cation requires extensive ductwork design. This is a low cost alternative to purchasing, installing, and maintaining multiple smaller tonnage units to meet the required air flow demand for the space.

Access to the 6 through 25 ton units is made through the back of unit by way of two panels, and/or through a side access panel if adjustment to the motor belt or motor base are needed.

Blower Housing

The blower housing is constructed of non-corrosive galvanized steel. A facto- ry-mounted orifice ring is provided for ease of motor serviceability on the 1/2 through 5-ton direct drive units.

All air-side panels are interchangeable with one another for ease of field con- vertibility of the supply-air on the GEH model.

Air-Side Filter

The air-side filter incorporates several- fiberglass options. These filters include an average synthetic dust weight arrestance of approximately 75%. This dust holding capability includes a color- less, odorless adhesive to retain dirt particles within the filter media after fiber contact.

Air-to-Refrigerant Coil

The air-to-refrigerant heat exchanger is constructed of staggered copper tubes with die-formed corrugated lanced alu- minum fins. The fins are then mechani- cally bonded to the tubes through expansion.

The coil is placed internal of the unit design for the GEH model to provides an optional dual filtration application. With dual filtration to the GEH unit, maintenance to the filter is significantly less than with a single filtration system. This design also offers maximum flexi- blity of the supply and return air config- urations.

The maximum working pressure for both the GEH and GEV coils is 450 psig. It is designed for maximum capacity with an additional benefit of physical unit size reduction.

Figure 15: 1/2 to 5-ton blower motor

Figure 16: 6 to 20-ton blower motor and fan belt assembly.

14

WSHP-PRC003-EN

Page 13 Page 15
Image 14
Page 13 Page 15
Contents WSHP-PRC003-EN Introduction Contents Digits 1-3 Unit Configuration Model NumberTable G2 General Data GEH 024 to General DataTable G1 General Data GEH 006 to Table G3 General Data GEH 060 toTable G6 General Data GEV 048 to Table G4 General Data GEV 006 toTable G5 General Data GEV 024 to 024 030 036 040 042072 090 120 150 180 Table G7 General Data GEV 072 toTable G8 General Data GEH 240Air-to-Refrigerant Coils Table G9 GEH/GEVTable G17 GEH/GEV 060 2-compr. circuit GEH 1/2 to 5-Ton Cabinet Features and BenefitsDesign Advantages GEV 1/2 to 5-Ton CabinetAirflow Options 1/2 to 5 ton Features BenefitsGEH/GEV 6 to 20-Ton Cabinet Airflow Options 6 to 20-tonHanging Device 6 to 12-1/2-ton Access Panels 12-1/2 to 20-tonHanging Device 1/2 to 5-ton Drain PanCompressor and Co-axial Coil Isolation 1/2 to 5 ton Schrader Connections 1/2 to 5-tonCo-axial Water-to-Refrigerant Coil Water Connections 1/2 to 5-tonBlower Motor 6 to 20 ton Blower HousingBlower Motor 1/2 to 5 ton Air-Side FilterBoilerless Control/Electric Heat option Waterside Economizer optionProper Hot Gas Design Hot Gas Reheat optionCommon Reheat Applications Controls Controls by TraneBasic 24 Volt Controls Safety DevicesBasic Controls Stand-alone SystemSmall Building Control Deluxe ControlsDeluxe 24V Electronic Controls Compressor Disable Deluxe 24V features include Random StartAnti-short Cycle Timer Safety ControlZN510 & ZN524 Controls Tracer ZN510 & ZN524 ControlsDirect Digital Controls Water Isolation Valves Entering Water Temperature SamplingWaterside Economizer Tracer ZN controller system installation Building Control AdvantagesHanging Devices and Duct Attachments Application ConsiderationsHanging the Horizontal Condensate trap installation Condensate TrapsDistributed Pumping System 40 F/ 4 C may require antifreeze in the water loopInstallation Made Easy Service Access

Model 180 GEV, 120 GEH, Model 012 GEH specifications

Trane, a leading name in HVAC (heating, ventilation, and air conditioning) systems, offers a diverse range of models designed to cater to different cooling needs. Among its notable products are the Trane Model 180 GEV, Model 120 GEH, and Model 012 GEH. Each of these units incorporates advanced technologies and features aimed at enhancing efficiency, durability, and overall performance.

The Trane Model 180 GEV is engineered for high-performance cooling and heating applications. One of its standout features is the variable-speed compressor, which allows for precise temperature control and significant energy savings. This model also integrates advanced inverter technology that optimizes energy consumption based on the load. The robust design of the unit ensures reliability even under extreme weather conditions, making it a favored choice for commercial and industrial sectors.

In contrast, the Trane Model 120 GEH is a versatile solution that focuses on efficiency and adaptability. This model is equipped with Trane’s exclusive Climatuff compressor technology, which enhances the reliability and longevity of the system. The Model 120 GEH also includes a user-friendly touchscreen interface, allowing for convenient adjustments and monitoring of the system's performance. Enhanced filtration systems contribute to improved indoor air quality, which is a critical factor for many users.

The Trane Model 012 GEH is designed for smaller spaces but does not compromise on performance. This compact unit boasts energy-efficient operation and is equipped with Trane’s proprietary Air-Cooled Scroll Compressors that enhance its cooling capacity while maintaining low operational noise levels. Its sleek design allows for easy installation in various settings, including residential areas. The Model 012 GEH also features enhanced reliability through its robust materials, ensuring that it can withstand varying environmental conditions.

All three models emphasize Trane’s commitment to sustainability and energy efficiency. With the incorporation of eco-friendly refrigerants and advanced heat exchange technologies, users can enjoy superior cooling performance while minimizing their environmental impact. Moreover, these models are backed by Trane’s comprehensive support, providing customers with peace of mind through warranties and service options.

In summary, Trane's Model 180 GEV, Model 120 GEH, and Model 012 GEH are exemplars of modern HVAC technology, offering various features tailored to meet specific cooling and heating requirements. Each model stands out for its unique capabilities, efficient operation, and robust design, reaffirming Trane's position as a trusted leader in the HVAC industry.
Top Page Image Contents