Honeywell K9696V2 installation instructions Temperature, USB port and Printer port

Page 21

 

 

Field Work

 

 

 

 

 

Table 3

 

 

 

Panel connectors

 

 

 

 

 

 

 

Connector Label

Description

 

 

 

 

 

SERIAL PORTS

General-purpose serial ports, DB9 connector.

 

VIDEO INPUTS – IN

BNC connectors for video signal cable from the cameras in a

 

 

CCTV system. A Multi-Media unit has 16 video input

 

 

connections.

 

VIDEO INPUTS – OUT

BNC connectors to relay a video feed to either a CCTV, NTSC

 

 

or PAL monitor, VCR, or other device. The outs are capped for

 

 

delivery.

 

MONITOR OUTPUT 1

BNC connector; can be set to produce test pattern or a

 

 

camera tour. Also called “Video spot out” on previous version

 

 

of unit.

 

MONITOR OUTPUT 2

BNC connector; inoperative for this release.

 

MOUSE

For standard mouse (supplied)

 

KEYBOARD

For keyboard (optional)

 

TELCO

RJ-11 connector to Multi-Media unit’s modem

 

USB PORT

Inoperative.

 

PARALLEL PORT

Inoperative.

 

LAN

RJ-45 connector to unit’s 10/100 BT network card

 

AUDIO IN/OUT

Soundcard connectors

 

MIC IN

DISABLED; use AUDIO IN.

 

ALARM INPUTS

Screw terminal connectors for input and ground*

 

 

connections, to interface with devices such as alarms. TTL

 

 

type: minimum high level of +2.4 volts; maximum low level of

 

 

+0.4 volts.

 

CONTROL OUTPUTS

Screw terminal connectors for output and ground*

 

 

connections, to interface with devices such as: lights, sirens,

 

 

locks, and so on. TTL type. The outputs do not directly drive

 

 

devices; they control relays that do so.

 

 

 

 

* Control I/O must be referenced to the ground of the Multi-Media unit.

USB port and Printer port

The USB port and Printer port at the back of the REMM unit are for future use.

Do not connect USB devices or a printer to a Multi-Media unit.

2.2Temperature

Honeywell recommends that a unit be operated in a non-condensing environment, in temperatures ranging from 40° F to 104°F (or 5°C to 40°C).

2–3

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Multi-Media Unit Page Issue Date Revisions Page Declaration of Conformity Page Table of Contents Frequent Questions Find-itIndex Page Page New to Multi-Media? OverviewNot new to Multi-Media? SoftwareWalking Through CamerasCommunications Powering-up the Multi-Media unit Admin and View SoftwareOther Hardware Log on to a Multi database, or create one using Admin Start Admin to create a Multi databaseUsing Admin, add a site Database for MultiRunning View Type of ConnectionAdd information about the connection, and save it About connectionsTesting a Connection Test the connection use View to run a Maintenance sessionLog on to View For More Information Where To, Next?Background information Audience Unpacking the UnitRoad map to field work Please do not remove factory seals on a Multi-Media unitRear Panel Reference Item, one of each, unless otherwise notedPrinted matter USB port and Printer port TemperaturePowering the Multi-Media Unit Reporting the InstallationPowering Up and Down Unit Recovery Connecting a CameraNominal storage* camera-day time† minute Rapid Dome or Rapid Dome Gold dome systemsSecuring a camera LocalViewReference HardwareTo enable the locking of a LocalView functions LocalView help on operator’s PCMonitors Network Connection To change a LocalView passwordRecording rate fps lowest cycle time sec OverviewTo assign an IP address to a unit using LocalView Using LocalView OnsiteFor a network without Dhcp What next?To setup a terminal program Using a PC OnsiteTo connect a null-modem cable Null-modem cable comes with your Multi-Media unitMulti-Media Unit Installation Instructions Hypertrm.exe icon Windows Click Start and point to … … then clickParameter Value To use the Multi-Media ShellCommand Result Field Name Default Address Shell commandMulti Shell Reference None, port1, port2, or internalTo return to the Multi-Media Shell after a time out Dial-up ConnectionField Testing a Connection Damaged or Missing GoodsModem Reference To upgrade a Multi-Media unit’s software, onsite Upgrade CD-ROMUpgrading Unit Software Multi-Media unit without a CD-RW drivePlease continue Road map for using Multi software to obtain video Why check a connection?Multi Software Some versions of Windows need you to restart the PC To install Multi softwareRunning Admin Using AdminObtaining a Multi Db After adding securityDouble-duty logon dialog Site identification checklist Adding Site InformationClick Save and Close To name a site Dealing with connections Record of a Dial-up ConnectionConfirmation To make a record of a dial-up connectionDealing with dial-up confusion Record of a Network Connection To make a record of a network connectionIP Address is mandatory for a network connection Using View to Connect Firewall referenceChecking for video Using Maintenance Testing a Connection MaintenanceTo run a maintenance session on a Rapid Eye site Logging on to ViewTesting a Connection Time Crucial settings for reporting on video of eventsTime zone To indicate the time zone of a Multi-Media unit Time zone is set on a unit-by-unit basisConflicting time zones To respond to a notification of conflicting time zones Clock Automatic settingAuto-synch statistics To set a unit’s clock manually, using a PC’sVideo tab in Maintenance session video feed adjustments Testing a Connection CameraTo configure a Rapid Eye site’s cameras Obtaining VideoTo obtain video from a live video session What Next ResultsPlease continue Microphones Audio at a Multi-Media SiteSelecting a microphone Placing a microphonePreventive measures Checking for Audio InterferenceAudio for Operators To enable talking to a siteAt View Operator’s PC To send and receive audio offsiteTo disable audio for LocalView To enable audio for use onsite, by LocalViewTo secure the unit Securing a Multi-Media unitDetachable Camera I/O Unit Hard DiskHard Disk Report To detach the sub-panelHandle on mounted hard disk Hardware OptionsConnecting a PTZ Dome Converter Technical NotesDaisy-chaining Domes Driver name Baud rate Supported controller/dome Alphabetical Configuring PTZInputs for Sensors Alarm SensorsInputs to a Multi-Media unit, used by hardware devices Input Technical NotesNo normally open NC normally closedSystem Monitoring Control OutputsSoftware setup To set the Fault Relay to trigger Alarm panelPoint of Sale Hardware Configuring POSExternal Modems At unit, connected to a networkPort Use Restrictions Using null-modem cable for installation of Multi-Media unitSerial connection Connect only to serial port COM USB port and Parallel portPlease continue Cannot connect to Multi-Media unit, using View Supporting an InstallationFrequently asked question Section No video is reaching View BackgroundSee also PlanningGrounding Coaxial CableLighting Electrical InterferenceHum bar Triaxial cableKnowledge Base Find-itTables Illustrations Use the same database created earlier, using Admin see on pDial-up Networking More FAQs Find-it More FAQsNetwork Connection More FAQs Find-it Organization personnel Personnel Name, telephone #, email Site Information ChecklistSite definition Rapid Eye site… Identification Audio Microphone type Speaker type Comments Communications to unit Connection ValueSite Information Checklist Find-it Sensor hardware Input Type NO, NC, EOL Description Site Information Checklist Find-it Multi-Media Unit Installation Instructions Index Multi-Media Unit Installation Instructions Index Page Page Page Page Honeywell Security Italia SpA Honeywell Security FranceHoneywell Security Espana Honeywell Security House Netherlands

K9696V2 specifications

The Honeywell K9696V2 is a state-of-the-art temperature control device designed for versatile applications in various heating and cooling systems. This advanced controller is known for its precision, reliability, and user-friendly interface, making it an essential component for modern HVAC setups.

One of the main features of the K9696V2 is its ability to support multiple control strategies. It can effectively manage single-stage and multi-stage heating and cooling systems, allowing it to be used in a wide range of residential and commercial applications. This flexibility ensures that users can easily integrate the controller into existing setups without significant modifications.

The K9696V2 incorporates advanced technologies such as microprocessor-based control. This ensures precise temperature management, enhancing comfort while minimizing energy consumption. It features a built-in temperature sensor that provides accurate readings, ensuring that the system operates within the desired range. Users can set temperature thresholds that the controller will maintain, making it ideal for environments where temperature stability is critical.

Another notable characteristic of the Honeywell K9696V2 is its user-friendly interface. The device is equipped with an intuitive digital display that provides real-time temperature readings and system status. Additionally, users can easily navigate through the menu to adjust settings without the need for complicated configurations, which is a significant advantage for both technicians and end-users.

The K9696V2 also offers robust communication capabilities. With support for various communication protocols, including Modbus and BACnet, the device can integrate seamlessly with building management systems. This connectivity allows for remote monitoring and control, giving facility managers greater oversight of their HVAC operations.

Finally, the Honeywell K9696V2 is designed with energy efficiency in mind. By optimizing system performance and providing precise control, this controller helps to reduce energy consumption, translating to cost savings for users. Its durable build ensures longevity, making it a worthy investment for those seeking reliable temperature control solutions.

Overall, the Honeywell K9696V2 stands out in the market due to its advanced features, adaptability, and user-centric design, making it a preferred choice for temperature control in a variety of settings.
Top Page Image Contents