Honeywell K9696V2 Dial-up Connection, To return to the Multi-Media Shell after a time out

Page 33

Field Work

After 10 minutes of inactivity, the Multi-Media Shell times out.

To return to it, turn the Multi-Media unit off, then use procedure 22.

!25 To return to the Multi-Media Shell after a time out

Turn the Multi-Media unit off, wait five seconds, then turn the unit on again and go back to the previous procedures.

The commands for the Multi-Media Shell are listed above in the Multi Shell Reference, on the next page.

2.8Dial-up Connection

For Telco communication, a data-grade (fax) telephone line is preferable to a standard line. Special features, such as call waiting, should not be available to a telephone line used by a Multi-Media unit.

Fig. 20. Detail of “TELCO” port, used for dial-up connection.

Honeywell recommends powering down a unit before connecting hardware to it. See 2.4.1: Powering Up and Down, p. 2–5.

!26 To connect the Multi-Media unit to a telephone line jack

1.Using a standard telephone cable with RJ-11 connectors, plug one connector into the unit’s TELCO port; see figure 20.

2.Plug the other connector in a telephone outlet.

Connect the unit to a telephone line only if a dial-up connection is used to communicate with the Multi-Media unit. For a network connection, please skip to section 2.7: Network Connection.

What next?

You are ready to power-up the camera(s) and unit as explained in section 2.4: Powering

the Multi-Media Unit, on p. 2–4.

2–15

Image 33
Contents Multi-Media Unit Page Issue Date Revisions Page Declaration of Conformity Page Table of Contents Frequent Questions Find-itIndex Page Page New to Multi-Media? OverviewNot new to Multi-Media? SoftwareWalking Through CamerasCommunications Powering-up the Multi-Media unit Admin and View SoftwareOther Hardware Log on to a Multi database, or create one using Admin Start Admin to create a Multi databaseUsing Admin, add a site Database for MultiRunning View Type of ConnectionAdd information about the connection, and save it About connectionsTesting a Connection Test the connection use View to run a Maintenance sessionLog on to View For More Information Where To, Next?Background information Audience Unpacking the UnitRoad map to field work Please do not remove factory seals on a Multi-Media unitRear Panel Reference Item, one of each, unless otherwise notedPrinted matter USB port and Printer port TemperaturePowering the Multi-Media Unit Reporting the InstallationPowering Up and Down Unit Recovery Connecting a CameraNominal storage* camera-day time† minute Rapid Dome or Rapid Dome Gold dome systemsSecuring a camera LocalViewReference HardwareTo enable the locking of a LocalView functions LocalView help on operator’s PCMonitors Network Connection To change a LocalView passwordRecording rate fps lowest cycle time sec OverviewTo assign an IP address to a unit using LocalView Using LocalView OnsiteFor a network without Dhcp What next?To setup a terminal program Using a PC OnsiteTo connect a null-modem cable Null-modem cable comes with your Multi-Media unitMulti-Media Unit Installation Instructions Hypertrm.exe icon Windows Click Start and point to … … then clickParameter Value To use the Multi-Media ShellCommand Result Field Name Default Address Shell commandMulti Shell Reference None, port1, port2, or internalTo return to the Multi-Media Shell after a time out Dial-up ConnectionField Testing a Connection Damaged or Missing GoodsModem Reference To upgrade a Multi-Media unit’s software, onsite Upgrade CD-ROMUpgrading Unit Software Multi-Media unit without a CD-RW drivePlease continue Road map for using Multi software to obtain video Why check a connection?Multi Software Some versions of Windows need you to restart the PC To install Multi softwareRunning Admin Using AdminObtaining a Multi Db After adding securityDouble-duty logon dialog Site identification checklist Adding Site InformationClick Save and Close To name a site Dealing with connections Record of a Dial-up ConnectionConfirmation To make a record of a dial-up connectionDealing with dial-up confusion Record of a Network Connection To make a record of a network connectionIP Address is mandatory for a network connection Using View to Connect Firewall referenceChecking for video Using Maintenance Testing a Connection MaintenanceTo run a maintenance session on a Rapid Eye site Logging on to ViewTesting a Connection Time Crucial settings for reporting on video of eventsTime zone To indicate the time zone of a Multi-Media unit Time zone is set on a unit-by-unit basisConflicting time zones To respond to a notification of conflicting time zones Clock Automatic settingAuto-synch statistics To set a unit’s clock manually, using a PC’sVideo tab in Maintenance session video feed adjustments Testing a Connection CameraTo configure a Rapid Eye site’s cameras Obtaining VideoTo obtain video from a live video session What Next ResultsPlease continue Microphones Audio at a Multi-Media SiteSelecting a microphone Placing a microphonePreventive measures Checking for Audio InterferenceAudio for Operators To enable talking to a siteAt View Operator’s PC To send and receive audio offsiteTo disable audio for LocalView To enable audio for use onsite, by LocalViewTo secure the unit Securing a Multi-Media unitDetachable Camera I/O Unit Hard DiskHard Disk Report To detach the sub-panelHandle on mounted hard disk Hardware OptionsConnecting a PTZ Dome Converter Technical NotesDaisy-chaining Domes Driver name Baud rate Supported controller/dome Alphabetical Configuring PTZInputs for Sensors Alarm SensorsInputs to a Multi-Media unit, used by hardware devices Input Technical NotesNo normally open NC normally closedSystem Monitoring Control OutputsSoftware setup To set the Fault Relay to trigger Alarm panelPoint of Sale Hardware Configuring POSExternal Modems At unit, connected to a networkPort Use Restrictions Using null-modem cable for installation of Multi-Media unitSerial connection Connect only to serial port COM USB port and Parallel portPlease continue Cannot connect to Multi-Media unit, using View Supporting an InstallationFrequently asked question Section No video is reaching View BackgroundSee also PlanningGrounding Coaxial CableLighting Electrical InterferenceHum bar Triaxial cableKnowledge Base Find-itTables Illustrations Use the same database created earlier, using Admin see on pDial-up Networking More FAQs Find-it More FAQsNetwork Connection More FAQs Find-it Organization personnel Personnel Name, telephone #, email Site Information ChecklistSite definition Rapid Eye site… Identification Audio Microphone type Speaker type Comments Communications to unit Connection ValueSite Information Checklist Find-it Sensor hardware Input Type NO, NC, EOL Description Site Information Checklist Find-it Multi-Media Unit Installation Instructions Index Multi-Media Unit Installation Instructions Index Page Page Page Page Honeywell Security Italia SpA Honeywell Security FranceHoneywell Security Espana Honeywell Security House Netherlands

K9696V2 specifications

The Honeywell K9696V2 is a state-of-the-art temperature control device designed for versatile applications in various heating and cooling systems. This advanced controller is known for its precision, reliability, and user-friendly interface, making it an essential component for modern HVAC setups.

One of the main features of the K9696V2 is its ability to support multiple control strategies. It can effectively manage single-stage and multi-stage heating and cooling systems, allowing it to be used in a wide range of residential and commercial applications. This flexibility ensures that users can easily integrate the controller into existing setups without significant modifications.

The K9696V2 incorporates advanced technologies such as microprocessor-based control. This ensures precise temperature management, enhancing comfort while minimizing energy consumption. It features a built-in temperature sensor that provides accurate readings, ensuring that the system operates within the desired range. Users can set temperature thresholds that the controller will maintain, making it ideal for environments where temperature stability is critical.

Another notable characteristic of the Honeywell K9696V2 is its user-friendly interface. The device is equipped with an intuitive digital display that provides real-time temperature readings and system status. Additionally, users can easily navigate through the menu to adjust settings without the need for complicated configurations, which is a significant advantage for both technicians and end-users.

The K9696V2 also offers robust communication capabilities. With support for various communication protocols, including Modbus and BACnet, the device can integrate seamlessly with building management systems. This connectivity allows for remote monitoring and control, giving facility managers greater oversight of their HVAC operations.

Finally, the Honeywell K9696V2 is designed with energy efficiency in mind. By optimizing system performance and providing precise control, this controller helps to reduce energy consumption, translating to cost savings for users. Its durable build ensures longevity, making it a worthy investment for those seeking reliable temperature control solutions.

Overall, the Honeywell K9696V2 stands out in the market due to its advanced features, adaptability, and user-centric design, making it a preferred choice for temperature control in a variety of settings.