Honeywell K9696V2 installation instructions Please continue

Page 70

Multi-Media Unit: Installation Instructions

Please continue.

5–12

Image 70

Contents Multi-Media Unit Page Issue Date Revisions Page Declaration of Conformity Page Table of Contents Find-it Frequent QuestionsIndex Page Page Not new to Multi-Media? OverviewNew to Multi-Media? SoftwareCameras Walking ThroughCommunications Admin and View Software Powering-up the Multi-Media unitOther Hardware Using Admin, add a site Start Admin to create a Multi databaseLog on to a Multi database, or create one using Admin Database for MultiAdd information about the connection, and save it Type of ConnectionRunning View About connectionsTest the connection use View to run a Maintenance session Testing a ConnectionLog on to View Where To, Next? For More InformationBackground information Road map to field work Unpacking the UnitAudience Please do not remove factory seals on a Multi-Media unitItem, one of each, unless otherwise noted Rear Panel ReferencePrinted matter Temperature USB port and Printer portReporting the Installation Powering the Multi-Media UnitPowering Up and Down Nominal storage* camera-day time† minute Connecting a CameraUnit Recovery Rapid Dome or Rapid Dome Gold dome systemsReference LocalViewSecuring a camera HardwareLocalView help on operator’s PC To enable the locking of a LocalView functionsMonitors Recording rate fps lowest cycle time sec To change a LocalView passwordNetwork Connection OverviewFor a network without Dhcp Using LocalView OnsiteTo assign an IP address to a unit using LocalView What next?To connect a null-modem cable Using a PC OnsiteTo setup a terminal program Null-modem cable comes with your Multi-Media unitMulti-Media Unit Installation Instructions Parameter Value Windows Click Start and point to … … then clickHypertrm.exe icon To use the Multi-Media ShellMulti Shell Reference Field Name Default Address Shell commandCommand Result None, port1, port2, or internalDial-up Connection To return to the Multi-Media Shell after a time outDamaged or Missing Goods Field Testing a ConnectionModem Reference Upgrading Unit Software Upgrade CD-ROMTo upgrade a Multi-Media unit’s software, onsite Multi-Media unit without a CD-RW drivePlease continue Why check a connection? Road map for using Multi software to obtain videoMulti Software To install Multi software Some versions of Windows need you to restart the PCUsing Admin Running AdminAfter adding security Obtaining a Multi DbDouble-duty logon dialog Adding Site Information Site identification checklistClick Save and Close To name a site Confirmation Record of a Dial-up ConnectionDealing with connections To make a record of a dial-up connectionDealing with dial-up confusion To make a record of a network connection Record of a Network ConnectionIP Address is mandatory for a network connection Firewall reference Using View to ConnectChecking for video To run a maintenance session on a Rapid Eye site Testing a Connection MaintenanceUsing Maintenance Logging on to ViewCrucial settings for reporting on video of events Testing a Connection TimeTime zone Time zone is set on a unit-by-unit basis To indicate the time zone of a Multi-Media unitConflicting time zones Clock Automatic setting To respond to a notification of conflicting time zonesTo set a unit’s clock manually, using a PC’s Auto-synch statisticsTesting a Connection Camera Video tab in Maintenance session video feed adjustmentsObtaining Video To configure a Rapid Eye site’s camerasTo obtain video from a live video session Results What NextPlease continue Selecting a microphone Audio at a Multi-Media SiteMicrophones Placing a microphoneChecking for Audio Interference Preventive measuresAt View Operator’s PC To enable talking to a siteAudio for Operators To send and receive audio offsiteTo enable audio for use onsite, by LocalView To disable audio for LocalViewSecuring a Multi-Media unit To secure the unitHard Disk Report Unit Hard DiskDetachable Camera I/O To detach the sub-panelHardware Options Handle on mounted hard diskConverter Technical Notes Connecting a PTZ DomeDaisy-chaining Domes Configuring PTZ Driver name Baud rate Supported controller/dome AlphabeticalAlarm Sensors Inputs for SensorsNo normally open Input Technical NotesInputs to a Multi-Media unit, used by hardware devices NC normally closedControl Outputs System MonitoringAlarm panel Software setup To set the Fault Relay to triggerExternal Modems Configuring POSPoint of Sale Hardware At unit, connected to a networkSerial connection Connect only to serial port COM Using null-modem cable for installation of Multi-Media unitPort Use Restrictions USB port and Parallel portPlease continue Supporting an Installation Cannot connect to Multi-Media unit, using ViewSee also BackgroundFrequently asked question Section No video is reaching View PlanningCoaxial Cable GroundingHum bar Electrical InterferenceLighting Triaxial cableFind-it Knowledge BaseTables Use the same database created earlier, using Admin see on p IllustrationsDial-up Networking More FAQs More FAQs Find-itNetwork Connection More FAQs Find-it Site Information Checklist Organization personnel Personnel Name, telephone #, emailSite definition Rapid Eye site… Identification Communications to unit Connection Value Audio Microphone type Speaker type CommentsSite Information Checklist Find-it Sensor hardware Input Type NO, NC, EOL Description Site Information Checklist Find-it Multi-Media Unit Installation Instructions Index Multi-Media Unit Installation Instructions Index Page Page Page Page Honeywell Security Espana Honeywell Security FranceHoneywell Security Italia SpA Honeywell Security House Netherlands

K9696V2 specifications

The Honeywell K9696V2 is a state-of-the-art temperature control device designed for versatile applications in various heating and cooling systems. This advanced controller is known for its precision, reliability, and user-friendly interface, making it an essential component for modern HVAC setups.

One of the main features of the K9696V2 is its ability to support multiple control strategies. It can effectively manage single-stage and multi-stage heating and cooling systems, allowing it to be used in a wide range of residential and commercial applications. This flexibility ensures that users can easily integrate the controller into existing setups without significant modifications.

The K9696V2 incorporates advanced technologies such as microprocessor-based control. This ensures precise temperature management, enhancing comfort while minimizing energy consumption. It features a built-in temperature sensor that provides accurate readings, ensuring that the system operates within the desired range. Users can set temperature thresholds that the controller will maintain, making it ideal for environments where temperature stability is critical.

Another notable characteristic of the Honeywell K9696V2 is its user-friendly interface. The device is equipped with an intuitive digital display that provides real-time temperature readings and system status. Additionally, users can easily navigate through the menu to adjust settings without the need for complicated configurations, which is a significant advantage for both technicians and end-users.

The K9696V2 also offers robust communication capabilities. With support for various communication protocols, including Modbus and BACnet, the device can integrate seamlessly with building management systems. This connectivity allows for remote monitoring and control, giving facility managers greater oversight of their HVAC operations.

Finally, the Honeywell K9696V2 is designed with energy efficiency in mind. By optimizing system performance and providing precise control, this controller helps to reduce energy consumption, translating to cost savings for users. Its durable build ensures longevity, making it a worthy investment for those seeking reliable temperature control solutions.

Overall, the Honeywell K9696V2 stands out in the market due to its advanced features, adaptability, and user-centric design, making it a preferred choice for temperature control in a variety of settings.