Honeywell 6271V manual System Overview contd, Fire Protection

Page 10

System Overview (cont'd)

Entry/Exit Delays

Your system has preset time delays, referred to as exit delay and entry delay. Whenever you arm your system, exit delay gives you time to leave through the designated exit door without setting off an alarm. Exit delay begins immediately after entering any arming command, and applies to all modes of arming protection. If programmed, a slow beeping will sound throughout the exit delay period. Additionally if programmed, a rapid beeping may sound during the final 10 seconds of the exit delay period.

Note: On some systems, pressing the Voice Status Icon restarts the exit delay. Refer to your control panel User Guide to see if this is applicable on your system.

Entry delay gives you time to disarm the system when you reenter through the designated entrance door. But the system must be disarmed before the entry delay period ends, or an alarm will occur. The keypad will beep during the entry delay period, reminding you to disarm the system. Ask your installer about the delay times programmed into your system.

Alarms

When an alarm occurs, the TouchCenter (and any other keypads) and external sounders will sound, and the zone(s) causing the alarm are displayed. If your system is connected to a central monitoring station, an alarm message will also be sent. To stop the alarm sounding, simply disarm the system.

Memory of Alarm

When an alarm condition occurs, the number(s) of the zone(s) that caused the problem are displayed, along with the type of alarm. These remain displayed until cleared.

Note: If you change screens, the alarm in memory can be viewed and cleared by selecting the Display Faults button on the Arming Screen.

Fire Protection

The optional fire protection portion of your security system (if used) is always on and will sound an alarm if a fire condition is detected. Note: If a fire or smoke detector develops a low battery, a “Fire Maintenance” message is displayed. To determine which zone is causing the problem, go to “Display Faults” to determine which zone has the low battery indication.

10

Image 10

Contents Ademco Table of Contents Table of Contents Contd Introduction About the TouchCenterTouchCenter Interface Navigating through the TouchCenter About the TouchCenter ContdAbout Your Home Screen Navigation Icon Descriptions Icon Location FunctionAway TouchCenter Arming ScreenStay Choices NightMore Icon MeaningIntroduction to Your System System OverviewBurglary Protection System Overview contd Fire ProtectionUser Codes Safe ModeExtended Functionality System Overview contd Arming Exit Entry Perimeter Interior Mode Delay Armed How to Arm the SystemFeatures for Each Arming Mode Security System OperationSecurity System Operation contd Screen ActionTo arm multiple partitions How to Arm Multiple PartitionsSelected How to Display Faults Bypass Zones, Enter CodeSecurity System Operation Contd How to Bypass Zones To bypass zones do the followingPress the Bypass Selected BypassPress the Back button to return to the Arming screen How to Remove Bypassed Zones Security System Operation contd How to Disarm the System To disarm the system when entering the premisesTo disarm the system when already in the premises Security System Operation Contd How to Check the Status of Other Partitions Security System Operation Contd How to Send Emergency Messages How to View the Event Log Next and Previous buttons will When All Partitions or All EventsNext and Previous buttons Case of Fire Alarm Fire Alarm System OperationIntroduction to Fire Alarm System Operation Silencing and Clearing a Fire AlarmFire Alarm System Operation contd Introduction to User Code Setup User Code SetupAuthority Levels How to Access User Setup User Code Setup contdAccess User Setup as follows How to Add a User Add a user as followsEnter User Code… displayed DigitsUser Code Setup Contd Selected, the Allow Arm/Disarm fromUser Code Setup contd Delete a User as follows How to Delete a UserAuthorized Code Edit a user as follows How to Edit a UserInstructions Enter Authorized Code User Code Setup Contd Console Emulation Mode Advanced System FeaturesIntroduction to Advanced System Features How to Enter Console Emulation ModeAdvanced System Features Contd Voice Messages Introduction to Recording and Retrieving MessagesRecording a Voice Message Voice Messages ContdTo record a voice message, do the following Retrieving and Deleting a Voice Message To retrieve a voice message, do the followingTouchCenter LED Operation Summary TouchCenter LED OperationLED Description How to Access Setup TouchCenter SetupHow to Access TouchCenter Setup Options Access the Setup features as followsTouchCenter Setup Contd How to Adjust the Touch Screen Contrast You may adjust the touch screen contrast as followsHow to Adjust the Volume How to Select Screen Backlight Off Activation Time Backlight Off After arrow button. aTouchCenter Setup Contd Button. a Settings Changed! pop-upHow to Select Homepage After Time TouchCenter Setup Contd How to Set the Time and Date TouchCenter Setup Contd Enter 2 digits for the hour TouchCenter Setup Contd TouchCenter Operating Modes How to Access Operating ModesAccess the Operating Modes feature as follows Operating Modes Chime, Voice, and Voice ChimeTouchCenter Operating Modes Contd Press the Operating ModesClean the TouchCenter as follows How to Clean your TouchCenterMaintaining Your System Maintaining Your System Contd Routine CareGlossary Glossary Contd Page Page Page Page Page Page ONE Year Limited Warranty