Honeywell 6271V manual User Codes, Extended Functionality, Safe Mode

Page 11

System Overview (Cont'd)

User Codes

Each user must be assigned a name with a corresponding 4-digit user code in order to gain access to various features and functions. Users for the system are programmed in a central user setup location that provides the specific questions for authorization level, partition assignment, and RF button assignment.

Extended Functionality

Extended functions are advanced functions that can be accessed through a standard alpha keypad or through the console emulation mode on your TouchCenter touch screen. Refer to your Control Panel User Guide for these features.

Safe Mode

The TouchCenter contains a Safe Mode of operation. In the rare event that the TouchCenter cannot successfully communicate in its graphic mode with the control panel, the Safe Mode is a backup mode that ensures that you can communicate with your system. In this mode, the TouchCenter operates much like a standard non-graphic keypad so that you can control your system until the problem is corrected.

If this situation occurs, the TouchCenter presents you with a message of “Problems detected. Start Keypad in Safe Mode?” and requests a “Yes” or “No” response. If you answer with “Yes”, the TouchCenter will go into the Safe Mode. If you answer with “No”, the TouchCenter will try communicating with the panel again. After 5 consecutive times of receiving no response, the TouchCenter will enter the Safe Mode automatically.

Note: Use care when providing the “Yes” or “No” response. Touching the screen outside the prescribed area may cause the backgound to come to the front. If this occurs, the Yes/No message that disappeared will time out in 30 seconds even though it is not visible. Then the keypad will reset into the Normal Mode (or Safe Mode if this is the third time that the warning message appeared).

While in the Safe Mode, the Home screen will display the Security button, Panic Button, and a message at the bottom of the screen as shown below:

11

Image 11

Contents Ademco Table of Contents Table of Contents Contd TouchCenter Interface About the TouchCenterIntroduction About Your Home Screen About the TouchCenter ContdNavigating through the TouchCenter Icon Location Function Navigation Icon DescriptionsStay TouchCenter Arming ScreenAway Icon Meaning NightMore ChoicesBurglary Protection System OverviewIntroduction to Your System Fire Protection System Overview contdExtended Functionality Safe ModeUser Codes System Overview contd Security System Operation How to Arm the SystemFeatures for Each Arming Mode Arming Exit Entry Perimeter Interior Mode Delay ArmedScreen Action Security System Operation contdSelected How to Arm Multiple PartitionsTo arm multiple partitions Bypass Zones, Enter Code How to Display FaultsSecurity System Operation Contd To bypass zones do the following How to Bypass ZonesBypass Press the Bypass SelectedPress the Back button to return to the Arming screen How to Remove Bypassed Zones Security System Operation contd To disarm the system when entering the premises How to Disarm the SystemTo disarm the system when already in the premises Security System Operation Contd How to Check the Status of Other Partitions Security System Operation Contd How to Send Emergency Messages How to View the Event Log Next and Previous buttons When All Partitions or All EventsNext and Previous buttons will Silencing and Clearing a Fire Alarm Fire Alarm System OperationIntroduction to Fire Alarm System Operation Case of Fire AlarmFire Alarm System Operation contd Authority Levels User Code SetupIntroduction to User Code Setup Access User Setup as follows User Code Setup contdHow to Access User Setup Add a user as follows How to Add a UserDigits Enter User Code… displayedSelected, the Allow Arm/Disarm from User Code Setup ContdUser Code Setup contd Authorized Code How to Delete a UserDelete a User as follows Instructions Enter Authorized Code How to Edit a UserEdit a user as follows User Code Setup Contd How to Enter Console Emulation Mode Advanced System FeaturesIntroduction to Advanced System Features Console Emulation ModeAdvanced System Features Contd Introduction to Recording and Retrieving Messages Voice MessagesTo record a voice message, do the following Voice Messages ContdRecording a Voice Message To retrieve a voice message, do the following Retrieving and Deleting a Voice MessageLED Description Summary TouchCenter LED OperationTouchCenter LED Operation Access the Setup features as follows TouchCenter SetupHow to Access TouchCenter Setup Options How to Access SetupTouchCenter Setup Contd You may adjust the touch screen contrast as follows How to Adjust the Touch Screen ContrastHow to Adjust the Volume Backlight Off After arrow button. a How to Select Screen Backlight Off Activation TimeButton. a Settings Changed! pop-up TouchCenter Setup ContdHow to Select Homepage After Time TouchCenter Setup Contd How to Set the Time and Date TouchCenter Setup Contd Enter 2 digits for the hour TouchCenter Setup Contd Operating Modes Chime, Voice, and Voice Chime How to Access Operating ModesAccess the Operating Modes feature as follows TouchCenter Operating ModesPress the Operating Modes TouchCenter Operating Modes ContdMaintaining Your System How to Clean your TouchCenterClean the TouchCenter as follows Routine Care Maintaining Your System ContdGlossary Glossary Contd Page Page Page Page Page Page ONE Year Limited Warranty