Kicker SX700.4, SX900.4 manual Frequency, bandwidth, Frequency and slope.Use the UP, Hz to 20325 Hz

Page 12

Operation

EQ MENU - This menu is where you adjust the single band parametric equalizer for each amplifier. There are two EQ menus, one for AMP 1 and one for AMP 2. This allows each amplifier to have its own individual EQ setting.

Use the UP and DOWN keys to

Use the UP and DOWN keys to select your Q value. Press the ESC to return to the selected amplifier’s EQ menu.

ESC HOME ENT

Lo-PassMENU - This menu is where you adjust the low pass crossover for each amplifier. There are two LO-PASS menus, one for AMP 1 and one for AMP 2. This allows each amplifier to have its own individual LO-PASS

setting.

When you are done adjusting the selected amplifier’s LO-PASS crossover press the ESC key to return to the LO-PASS menu AMP-1 / AMP-2options to select the other amplifier.

ESC HOME ENT

scroll through AMP-1and AMP-2and press the ENT key to select the

BOOST/CUT is how much you want to boost or cut the equalizer and has a range of -18 dB to + 18 dB in .5 dB

Use the UP and DOWN keys to scroll through AMP-1and AMP-2and

If done adjusting the LO-PASS crossover, press the ESC key again

amplifier you want to adjust.

ESC HOME ENT

steps.

press the ENT key to select the amplifier you want to adjust.

ESC HOME ENT

to return to the MAIN menu

ESC HOME ENT

Your options for each amplifier are

frequency, bandwidth and

Use the UP and DOWN keys to adjust each setting and the ESC

Your options for each amplifier are

NOTE...

Operation

boost/cut. Use the UP and DOWN keys to choose one and press the

key to return to the selected amplifier’s EQ menu.

ESC HOME ENT

frequency and slop[e.Use the UP

and DOWN keys to choose one and

While adjusting the LO-PASS crossover you will notice the LPF indicator on the ISIS VFD display is lit. This indicates

ENT key to select it.

ESC HOME ENT

press the ENT key to select it.

ESC HOME ENT

you are in the LO-PASS crossover menu.

FREQUENCY selects the center frequency of the EQ and can be set at any 1/12th octave frequency from 20 Hz - 20 kHz.

(20 Hz to 20325 Hz)

Use the UP and DOWN keys to select your frequency. Press the

When you are done adjusting the selected amplifier’s EQ press the ESC key to return to the EQ menu AMP-1 / AMP-2options to select the other amplifier.

If done adjusting the EQ, press the

ESC HOME ENT

FREQUENCY selects the crossover point and can be set at any 1/12th octave frequency from 30 Hz to 20 kHz.

(30 Hz to 20325 Hz)

Use the UP and DOWN keys to

select your frequency. Press the

The AMP1 or AMP 2 indicator will light up to indicate which amplifier you are currently adjusting.

The KICKER SX amplifier monitors and prevents any low pass crossover point from being any closer than 1/3 octave from the high pass crossover point. If you cannot set the low pass

ESC to return to the selected amplifiers EQ menu.

ESC HOME ENT

ESC key again to return to the MAIN menu

ESC HOME ENT

ESC to return to the selected

ESC HOME

ENT

 

 

amplifier’s LO-PASS menu.

 

 

crossover where you want then check the HPF indicator and see if it is flashing. If it is then you need to go to the HI-PASS menu and raise the high pass crossover point.

BANDWIDTH (better known as Q) can be set from .5 to 10 in

.5 increments. In simple terms, lower Q effects more frequencies around the center frequency while higher Q effects fewer frequencies around the center frequency.

NOTE...

While adjusting the EQ you will notice the EQ indicator on the ISIS VFD display is lit. This indicates you are in the EQ menu.

The AMP1 or AMP 2 indicator will light up to indicate which

SLOPE selects the rolloff of the crossover and can be set from oFF to 36 dB in 6 dB steps.

Use the UP and DOWN keys to select your slope. Press the ESC to return to the selected amplifier’s

This is done as a safety precaution to prevent a notch filter condition.

amplifier you are currently adjusting.

LO-PASS menu.

ESC HOME ENT

22

SX .4 Series Amplifiers

SX .4 Series Amplifiers

23

Image 12
Contents Page Features AmplifierVFD Display VFD DisplayM1 M2 M3 M4 Installation End Panel ViewsMounting Wiring Four Channel Operation StereoTWO Channel Operation Bridged Using the Signal Output Jacks Past Stereo and Bridged SimultaneouslyUsing the Remote Bass Level Control & Blast NavigationLo-Pass Hi-Pass Phase Mute Kompressor Security SystemMenu System Press HoldNoise OFf C...1, 2, 3...etcSick BAY ESC key to return to the Sick ESCMemory-1 Memory-2 Memory-3 Are Both AMPS, AMP-1 only and AMP-2 only1V, 2V, 4V, 8V AMP-1 /AMP-2 menuSelect Skip Reset or do Reset ESC Home ENT A, B, C...1, 2, 3...etcFrequency, bandwidth Frequency and slope.Use the UPHz to 20325 Hz Hz to 16132 Hz Down keys to choose one and press the ENT key to select itOperation Select Lock IT UP or DON’T Lock Unlock AmplifierMemory Presets Troubleshooting €Other SymptomsHelp €Green LED off, no outputModel SX700.4 SX900.4 RMS Power Dynamic PowerKompressor PerformanceSignal-t0-Noise Ratio Power & Ground TerminalsDSP Reaction Time / Delay HeightPizza Delivery Chic’s Numbers Hook Ups

SX900.4, SX700.4 specifications

Kicker has long been a trusted name in the world of car audio, and their SX series amplifiers, specifically the SX700.4 and SX900.4, stand as proud representatives of the brand's commitment to superior sound quality and innovative technology. These amplifiers are designed to elevate your mobile audio experience, making them ideal choices for enthusiasts seeking high performance and reliability.

The Kicker SX700.4 is a four-channel amplifier that delivers 700 watts of peak power, providing ample power to drive multiple speakers simultaneously. Its RMS power output stands at an impressive 100 watts per channel at 4 ohms, making it capable of pushing even the most demanding speaker configurations. With a frequency response range of 20 Hz to 20 kHz, the SX700.4 ensures that both low bass and crisp highs are reproduced accurately, allowing for a rich and immersive listening experience.

On the other hand, the Kicker SX900.4, with its robust 900 watts of peak power, takes performance to the next level. The amplifier boasts a RMS output of 125 watts per channel at 4 ohms, offering additional headroom for larger speaker systems or subwoofers. With advanced circuitry and high-quality components, the SX900.4 delivers clarity and precision, bringing out the details in your favorite music.

One of the standout features of both models is their innovative technology, including Kicker’s Gain, Bass Boost, and crossover controls. These features allow users to customize their audio setup according to personal preferences and specific vehicle acoustics. The built-in crossovers enable seamless integration with various speaker types, ensuring that each component of your system works harmoniously.

Both amplifiers also incorporate Kicker’s modern design, with a sleek, durable chassis that not only looks good but also enhances heat dissipation for long-lasting performance. Additionally, the internal protection circuitry provides peace of mind, safeguarding the amplifiers from overheating, short circuits, and other potential damage.

The Kicker SX700.4 and SX900.4 are perfect for those looking to upgrade their car audio system with powerful, high-quality amplification. Whether you're a casual listener or a dedicated audiophile, these amplifiers promise a significant enhancement to your audio experience, making every journey more enjoyable with rich, dynamic sound.