Kicker SX700.4, SX900.4 manual Memory Presets

Operation

Memory Presets

There are four memory preset keys each with an indicator above it in the ISIS VFD display. The indicator will illuminate if that

STORING A PRESET

Make all the adjustments you want to have stored in the preset and return to the DEFAULT screen.

PRESET PRESETS	Memory-1sets Amp 1 and Amp 2 into full-range mode with
	a infrasonic filter (often called subsonic filter) to protect the
Ok, we know that sounds like a certain pizza commercial,	speakers from harmful ultra-low frequencies.
but seriously the four memory presets come with settings	Memory-2sets Amp 1 and Amp 2 into high-pass operation.
already in them.

Operation

memory preset is currently in use.

To store your settings into a preset simply press and hold the desired

HOLD

	Used for powering up a set of coaxial or component speakers
You can use these as a starting point to do your own	when another amp is driving a subwoofer.

Each preset stores all the values for each of the following amplifier controls:

AMP1 AMP2

LOCK LEFT SYS RIGHT MUTE GAIN EQ LPF HPF PHASE KOMP

* kicker *

MEM-1 MEM-2 MEM-3 MEM-4

memory key until the VFD display flashes STORED . Then release the memory key. The indicator which matches the preset you used will illuminate.

RECALLING A PRESET

M1 M2 M3 M4

AMP1 AMP2

LOCK LEFT SYS RIGHT MUTE GAIN EQ LPF HPF PHASE KOMP

stored

MEM-1 MEM-2 MEM-3MEM-4

tweaking or for quick push-a-button-and-be-done setup.	Memory-3sets Amp 1 and Amp 2 into low-pass operation
Any preset you store will replace the ones that come from	with a infrasonic filter. For use when the amplifier is driving a
the factory. You can reset all four preset back to factory	subwoofer.
defaults anytime simply by doing a reset in the RESET AMP	Memory-4sets the amplifier up for Bi-Amp duty. Amp 1 is
menu.

*.) GAIN	INDICATORS		PRESETS
*.) EQ
*.) LO-PASS
*.) HI-PASS	M1	M2 M3	M4
*.) PHASE
*.) MUTE
*.) KOMPRESSOR	ESC	HOME	ENT

This gives you the ability to dial in four completely different

amplifier settings and store them in presets for instant recall later.

It’s like a preset for your favorite radio stations...only better!

To recall a memory preset simply press and release the key. The matching indicator will light up and the amplifier will change all the corresponding controls to the values assigned to the memory pre- set.

PRESS &

RELEASE

M1 M2 M3 M4

AMP1 AMP2

LOCK LEFT SYS RIGHT MUTE GAIN EQ LPF HPF PHASE KOMP

* kicker *

MEM-1 MEM-2MEM-3 MEM-4

					setup for use with coaxials or component speeakers. Amp 2 is
Here are the settings in each preset from the factory.					setup for subwoofer duty with an infrasonic filter.
In more general terms, each preset offers you these					As stated before you can always start with one of these
options.										presets, tweak
		MEMORY-1		MEMORY-2		MEMORY-3		MEMORY-4		it to fit your
		Amp-1	Amp-2	Amp-1	Amp-2	Amp-1	Amp-2	Amp-1	Amp-2
										installation and
	GAIN LEVEL	6 DB	6 DB	6 DB	6 DB	6 DB	6 DB	6 DB	6 DB
										then save your
	EQ FREQUENCY	40 HZ	40 HZ	40 HZ	40 HZ	40 HZ	40 HZ	40 HZ	40 HZ
										settings into a
	EQ BOOST/CUT	FLAT	FLAT	FLAT	FLAT	FLAT	FLAT	FLAT	FLAT	new preset.
	EQ BANDWIDTH	3	3	3	3	3	3	3	3
	LO-PASS SLOPE	OFF	OFF	OFF	OFF	24 dB	24 dB	OFF	24 DB
	LO-PASS FREQ	20325 HZ	20325 HZ	20325 HZ	20325 HZ	84 HZ	84 HZ	20325 HZ	84 HZ
	HI-PASS SLOPE	12 DB	12 DB	24 DB	24 DB	24 DB	24 DB	24 DB	24 DB
	HI-PASS FREQ	25 HZ	25 HZ	84 HZ	84 HZ	25 Hz	25 Hz	84 HZ	25 HZ
	PHASE L&R CH.	0 DEGREE	0 DEGREE	0 DEGREE	0 DEGREE	O DEGREE	O DEGREE	O DEGREE	O DEGREE
	MUTE L&R CH.	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF
	KOMPRESSOR	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF
	KOMP ADJ.	0 DB	0 DB	0 DB	0 DB	0 DB	0 DB	0 DB	0 DB

30 SX .4 Series Amplifiers SX .4 Series Amplifiers 31