Bosch Appliances APC-AMC2-4WCF, APC-AMC2-4WUS installation manual Table of Contents

Page 4

4 en		AMC2 4W
Table of Contents

1	Please read carefully	7
1.1	Explanation of Used Symbols	7
1.2	Internet	7

2	Safety Instructions	8
2.1	Important Safety Notes	8
2.2	FCC & ICES Information	10
2.3	Safety Precautions	11
2.4	Unpacking	12

3	Introduction	13
3.1	Description of the AMC2 4W	13
3.2	Equipment Configuration	15
3.3	Performance Characteristics	18
3.4	System Overview	19

4	Technical Data	20

5	Installing	22
5.1	Mounting	22
5.2	Demounting	23
5.3	Opening the AMC2 4W Case	24
5.4	Cabling	25
5.4.1	Conductor data for connection to power supply	25
5.4.2	Grounding and Shielding the Host Interface	26
5.4.3	Grounding and Shielding the Extension Interface	28
5.5	Connecting Power Supply	28
5.6	RS-485 Host Interface	30
5.6.1	RS-485 Two Wire Connection	32
5.6.2	RS-485 Four Wire Connection	33
5.6.3	DIL Switch Address Selector	34
5.7	RS-232 Host Interface	36
5.8	Ethernet Interface	37

F.01U.024.965 V.4 2006.09

Installation manual

Bosch Security Systems

Image 4

Contents AMC2 4W Page Remarks Table of Contents Appendix OperatingIndex AMC2 4W Please read carefully Explanation of Used SymbolsInternet Safety Instructions Important Safety NotesSafety Instructions en FCC & Ices Information Health and Safety Safety PrecautionsRead instructions Unpacking Introduction Description of the AMC2 4WAMC2 4W in a four door safety lock Equipment Configuration Upper circuit board with display top sideOverview Interfaces Jumper at the bottom side Performance Characteristics System Overview System overviewTechnical Data RTCAMC 5VA Installing MountingDemounting Opening the AMC2 4W Case Cabling Conductor data for connection to power supplyGrounding and Shielding Grounding and Shielding the Host Interface Location of ground jumper RS-485 host interfaceAMC2 4W Connecting Power Supply Grounding and Shielding the Extension InterfaceLocation of the power supply connector RS-485 Host Interface AMC2 4W 1 RS-485 Two Wire Connection RS-485 host interface2 RS-485 Four Wire Connection 10 Settings for RS-485 two wire connectionsDIL Switch Address Selector 12 Settings for RS-485 four wire connectionAMC2 4W Mode DIL Switches Address DIL SwitchesRS-232 Host Interface Ethernet Interface 14 Location of the RS-232 serial interfaceIpconfig /flushdns RS-485 Extension Module Bus Wiegand Interface for Card Readers17 Location of the Wiegand interfaces for external devices Connecting Relay Outputs 18 Location of the relay output connectorsKeep in mind the following specifications 19 Wet mode and dry mode of the AMC2 4W relay outputs20 Schema of the using of the recovery diode Risk of DamageConnecting Analog Input Devices 21 Location of relay output jumpers bottom sideComplete connection diagram of the analog input devices is Tamper Protection AMC2 4W Operating Status Display of the AMC2 4WDig. IO Push Display Example DescriptionDig Resetting the AMC2 4W Configuring the Ethernet InterfaceResetting the Software Resetting the Network Configurations Restarting the AMC2 4W with the provided screw driverAMC2 4W Connecting Diagrams AppendixConnecting diagram of the RS-232 serial interface AMC2 4W Power supply Twisted pair connection Transmitter Receiver Index I L O PPage Bosch Security Systems