Bosch Appliances APC-AMC2-4WCF Cabling, Conductor data for connection to power supply

Page 25

AMC2 4W

Installing en 25

5.4Cabling

CAUTION!

The cables used in the AMC2 4W access control system are not

!prone to electrical interference. However, you should avoid routing cables close to heavy load switching cables and equip-

ment. If this is unavoidable, cross the cable at right angles every 1 to 2 m (3 to 6 ft) to reduce interference.

Grounding and Shielding

The main grounding point at the AMC2 4W will be connected with pin 2 of the power supply connector - see Figure 7.6.

It is good practice to shield all wires carrying low level signals.

The AMC2 4W enables you to set up a central ground or shield- ing point, simply by setting a couple of jumpers. Set these jumpers only if ground or shield is not connected otherwise.

WARNING!

!Risk of damaging equipment!

When using multiple AMC2 4W devices, set the ground main jumper only once to assure a central point star connection.

5.4.1Conductor data for connection to power supply

For short distances below 25m (75 feet) use AWG18 conduc- tors. For higher distances install an additional power supply close to the AMC.

Please, calculate the voltage drop by checking the conductor specifications for characteristic resistance values. The voltage drop shall not exceed 2V.

Example:

Length = 100m/328 ft

Bosch Security Systems

Installation manual

F.01U.024.965 V.4 2006.09

Page 24 Page 26
Image 25
Page 24 Page 26
Contents AMC2 4W Page Remarks Table of Contents Appendix OperatingIndex AMC2 4W Please read carefully Explanation of Used SymbolsInternet Important Safety Notes Safety InstructionsSafety Instructions en FCC & Ices Information Health and Safety Safety PrecautionsRead instructions Unpacking Description of the AMC2 4W IntroductionAMC2 4W in a four door safety lock Upper circuit board with display top side Equipment ConfigurationOverview Interfaces Jumper at the bottom side Performance Characteristics System overview System OverviewRTC Technical DataAMC 5VA Mounting InstallingDemounting Opening the AMC2 4W Case Cabling Conductor data for connection to power supplyGrounding and Shielding Location of ground jumper RS-485 host interface Grounding and Shielding the Host InterfaceAMC2 4W Grounding and Shielding the Extension Interface Connecting Power SupplyLocation of the power supply connector RS-485 Host Interface AMC2 4W RS-485 host interface 1 RS-485 Two Wire Connection10 Settings for RS-485 two wire connections 2 RS-485 Four Wire Connection12 Settings for RS-485 four wire connection DIL Switch Address SelectorAMC2 4W Mode DIL Switches Address DIL SwitchesRS-232 Host Interface 14 Location of the RS-232 serial interface Ethernet InterfaceIpconfig /flushdns Wiegand Interface for Card Readers RS-485 Extension Module Bus17 Location of the Wiegand interfaces for external devices 18 Location of the relay output connectors Connecting Relay Outputs19 Wet mode and dry mode of the AMC2 4W relay outputs Keep in mind the following specificationsRisk of Damage 20 Schema of the using of the recovery diode21 Location of relay output jumpers bottom side Connecting Analog Input DevicesComplete connection diagram of the analog input devices is Tamper Protection AMC2 4W Status Display of the AMC2 4W OperatingDig. IO Push Display Example DescriptionDig Resetting the AMC2 4W Configuring the Ethernet InterfaceResetting the Software Restarting the AMC2 4W with the provided screw driver Resetting the Network ConfigurationsAMC2 4W Appendix Connecting DiagramsConnecting diagram of the RS-232 serial interface AMC2 4W Power supply Twisted pair connection Transmitter Receiver I L O P IndexPage Bosch Security Systems

APC-AMC2-4W, APC-AMC2-4WUS, APC-AMC2-4WCF specifications

Bosch Appliances has been a leader in innovation and reliability in the home appliance sector, and their APC-AMC2-4WUS, APC-AMC2-4W, and APC-AMC2-4WCF models epitomize this commitment. These top-of-the-line dishwashers are designed to offer unparalleled performance, efficiency, and convenience for modern households.

One of the standout features of these models is their impressive cleaning technology. Bosch incorporates PrecisionWash, a system that uses intelligent sensors to continually scan and check the progress of dishes throughout the cycle, ensuring that every item is thoroughly cleaned. Paired with durable and flexible loading options like the RackMatic system, these dishwashers can accommodate diverse dishware sizes, making it easy to load everything from large pots to delicate glassware.

Energy efficiency is another key characteristic of the APC-AMC2 series. They are Energy Star certified, ensuring that you not only save on utility bills but also contribute to a more sustainable environment. The EcoSilence Drive motor reduces noise significantly, allowing for near-silent operation even during the heaviest cycles.

User convenience is prioritized in the design of these models. The EasyGlide rack system allows for smooth loading and unloading, while the TimeLight feature projects the remaining time on the floor, keeping users informed about the washing process without having to open the door.

Moreover, the APC-AMC2-4WCF model is equipped with the AquaStop system, which provides double protection against leaks, ensuring peace of mind for homeowners.

The overall aesthetic of Bosch dishwashers, combined with their robust performance, makes them an ideal addition to any kitchen. The sleek stainless-steel finish complements a variety of design themes, while a user-friendly control panel with a clear LCD display simplifies operation.

In conclusion, Bosch Appliances' APC-AMC2-4WUS, APC-AMC2-4W, and APC-AMC2-4WCF represent the pinnacle of modern dishwashing technology. With advanced cleaning capabilities, energy efficiency, and innovative user-centric features, these dishwashers are perfect for anyone looking to streamline their kitchen chores without sacrificing performance or style. Investing in a Bosch dishwasher is investing in reliability, efficiency, and quality.
Top Page Image Contents