Icom IC-M504 HM-162/HM-157 installation, Return the cables and screws to the original position

Page 69

rReturn the cables and screws to the original position.

• Be sure not upside down the flat cable.

CAUTION:

When re-assembling the case and tightening the screws, you must keep the specified torque (0.5±0.07 N.m). Oth- erwise the transceiver may be damaged (torque too high) or lose waterproof efficiency (torque too low).

When uninstalling the optional unit, remove it vertically. Wiggling the unit from side to side may damage the op- tional unit's connector.

CONNECTIONS AND MAINTENANCE 9

HM-162/HM-157 installation

 

 

 

 

HM-162

HM-157

 

9

 

 

 

 

The optional HM-157 can be connected to the transceiver di- rectly, as well as via the supplied connection cable for longer distance remote operation. The connector of the connection cable can be installed into a cabinet, wall, etc., as a built-in plug.

The optional HM-162 should be installed to the transceiver using the supplied connection cable.

For longer distance remote operation, the optional extension cable, OPC-1541/OPC-999* (6 m; 20 ft/connecting between transceiver and the connection cable), is available, and up to two OPC-1541/OPC-999* can be added.

*OPC-1541 : For the HM-162

OPC-999 : For the HM-157

Do not connect the HM-162 to the OPC-999, and the HM- 157 to the OPC-1541.

63

Image 69
Contents IM504 May occur Word DefinitionEquipment damage may occur Personal injury, fire or electric shockCase of Emergency Iii Determining MPE RadiusTable of Contents Precautions Radio license for boaters U.S.A. only Operating RulesShip Station License OPERATOR’S LicenseFront panel Panel Description2TRANSMIT Power KEY H/L Function display 0TIME Zone Indicator1POSITION Indicator 2SCAN IndicatorMicrophone Channel selection Basic OperationChannel Channel 9 Call channelWeather channels S.A., international and Canadian channelsC to change the channel group, if necessary Rotate Dial to select a channelReceiving and transmitting Call channel programming While pushing and holdingPush CH/WXDUAL Microphone Lock function Channel commentsDisplay backlight Select the desired characOptional voice scrambler operation Activating the scrambler Programming scrambler codesDialenter Scan types Scan OperationPriority Scan Normal ScanSetting TAG channels Clearing or setting all tagged channelsStarting a scan Description DUALWATCH/TRI-WATCHOperation DUALWATCH/TRI-WATCH SimulationMmsi code programming DSC OperationRotate Dial to select Mmsi Check, push Dialenter Rotate Dial to set the specific 9-digit Mmsi codeCheck the 9-digit Mmsi DSC self ID code Mmsi code checkProgramming Individual ID DSC address IDRotate Dial to select AddINDV ID, push Dialenter Rotate Dial to set the individual ID and ID nameDeleting Individual ID Rotate Dial to select Delindv ID, push DialenterRotate Dial to select the desired ID name for deleting Programming Group ID Rotate Dial to select AddGroup ID, push DialenterRotate Dial to set the group ID and ID name Rotate Dial to select DELGroup ID, push Dialenter Deleting Group IDPosition and time programming GPS information indication Position and time indicationDistress call Simple callAfter 2 sec. Wait ACK Regular call Distress alert contains defaultPush Distress for 5 sec. to transmit the distress call Transmitting an individual call Transmitting DSC callsPush Dialenter to transmit the individual call Transmitting an individual acknowledgement Transmitting a group call Push Dialenter to transmit the group call Transmitting an all ships call Rotate Dial to select the desired category, push DialenterPush Dialenter to transmit the all ships call Transmitting a position request call Push Dialenter to transmit the position request call Transmitting a position report call Push Dialenter to transmit the position report call Push Dialenter to transmit the polling request call Transmitting a polling request callTransmitting a position request reply call Your position data is transmitted, when Dialenter is pushed Transmitting a position report reply call Transmitting a polling request reply call Receiving a distress call Receiving DSC callsReceiving a distress acknowledgement Receiving a distress relay callReceiving an individual call Receiving a group callReceiving an all ships call Receiving a geographical area call Receiving a position request callReceiving a position report call Receiving a position request reply call Receiving a polling request callReceiving a position report reply call Receiving a polling request reply callDistress message Received messagesRotate Dial to select Distress, push Dialenter Rotate Dial to scroll the messageRotate Dial to select Other, push Dialenter Other messagesDSC Set mode No offset time defaultRotate Dial to select Offset Time, push Dialenter Automatic acknowledgement Rotate Dial to select Auto ACK, pushPush Dialenter to set the condition Rotate Dial to select Nmea Output, push Dialenter Nmea OutputOther Functions Intercom operationHM-162 listener RX Speaker function Push Hailrx to enter hailer mode Hailer operationTo return to normal operation, push CLR or Hailrx Underway Automatic foghorn functionStop SailRotate Dial to adjust the foghorn level, push Dialenter Tion is interrupted with an automatic return to the transIng DSC calls.’ p Set mode programming SET ModeSet mode items Scan resume timerDual/Tri-watch Weather alertBeep tone LCD contrastAutomatic foghorn frequency Radio powerScrambler type Scrambler codeConnections and Maintenance 0DC Power ConnectorConnections Fuse replacement Supplied accessoriesAntenna Mounting the transceiver Using the supplied mounting bracketMB-75 installation Tighten the end bolts on the clamps rotate clockwise soThat the clamps press firmly against the inside UT-112/UT-98 installation Return the cables and screws to the original position HM-162/HM-157 installationHM-162 Completed installation should look like thisHM-157 HM-162 HM-157Gasket Mm 131⁄32˝ Nut Cap Problem Possible Cause Solution TroubleshootingSpecifications Specifications and OptionsGeneral Receiver TransmitterOptions DimensionsFor mounting the transceiver to a panel 20 feet microphone extension cable for optional HMTransmit Receive Channel ListTemplate R12 MaxUnit mm inch Cut here Page Memo Kamiminami, Hirano-ku, Osaka 547-0003, Japan