First Alert FA1220CV General Rules on, Authority Levels, Changes, To Exit User Edit, Mode

Page 28

Technical Manuals Online! - http://www.tech-man.com

SECURITY CODES & AUTHORITY LEVELS

General Rules on	• A user may not delete or change the user code of the SAME or HIGHER authority than which
Authority Levels		he is assigned.
and Changes	• A master/manager may only ADD users to a LOWER authority level.

	•	A master/manager may assign access codes only to those partitions to which the user adding
		the code has access. (ex. a user with access to only partition 1 cannot assign codes in
		partition 2.)
	•	The only way to assign a user's authority level is by using the "Add A User" procedure. To
		change a user's authority level, that user must first be deleted, then added again.
	• A user can only be DELETED or CHANGED from within the partition he is assigned.
	• User numbers must be entered as 2-digit entries. Single digit user numbers must be
		preceded by a "0" (example, 03, 04, etc.). Security codes are entered as 4-digit numbers.
	•	Before assigning a security code, be sure it does not conflict with any DURESS code or other
		user code.
	Note: When adding, changing or deleting users, all other alpha keypads in that partition will
	display "User Edit Mode – Please Stand By", and key depressions (except Panic) at those
	keypads will be ignored. Panic key depressions will cause an alarm and terminate user entry.
To Exit User Edit	You can exit any of the user edit modes described on the following pages at any time by doing
Mode	the following:

	1.	Press either	✱	or	#	, or don't press any key for 10 seconds.

– 28 –

Image 28

Contents Users Guide Table of Contents System Overview General Partitioned System ZonesArming Features For Each Arming Mode System Overview System Overview General About the KeypadsAlpha Keypad Fixed-Word Keypad 0000 Online Functions of the Keypad OFFTechnical Manuals Online General Information ENTRY/EXIT DelaysPartition To show faulted zones Using Ready KeyChecking for Open Zones Displaying ALL Zone Descriptors Using Bypass Key Bypassing Protection ZonesTo bypass zones, the system must be disarmed first Enter your security code and pressQuick Bypass To use the Quick Bypass featureDisplaying Bypassed Zones Using Stay key Arming Perimeter onlyWith Entry Delay OFF Using Instant KeyUsing Away Key Arming ALL ProtectionUsing Maximum Key Using the 1 OFF Key Memory of Alarm Disarming and Silencing AlarmsTo disarm the system and silence burglary or fire alarms Using the Keyswitch GeneralChime Mode Using KeyViewing Central Station Messages MESSAGE. Press For 5 SecsActive Panic Functions Panic KeysKeys Zone Function Security Codes & Authority Levels InformationDuress Code Quick ArmingSecurity Codes & Authority Levels General Rules on Authority LevelsChanges To Exit User EditTo Add a User Enter Master or Manager code and pressLimited Use User #84 Command To Add a UserTo Change a Users Code To Delete a UserAccessing Other Partitions To Goto another partition using an alpha keypadSpeed Key Macros General Information Defining ExecutingUsing #70 Relay Menu Mode FA1220CV Event Logging Procedures Select the partitionFA1220CV Event Logging Procedures To Exit the Event Log Press at any timeTesting the System Using Test KeyTesting Your SystemTrouble Conditions Typical Check DisplaysServicing Information Alarm Silencing a FireSmoke Detectors for Minimum Protection Steps to Safety Emergency EvacuationMaintaining Your System Maintaining Your System Quick Guide to FA1220CV System Functions Quick Guide to FA1220CV System Functions Summary of Audible Notification Glossary Federal Communications Commission FCC Part 15 Statement UL Notice This is a Grade a systemFederal Communications Commission FCC Part 68 Notice Canadian Department of Communications DOC Statement Limitations of this Alarm System Limitations of this Alarm System Owners Insurance Premium Credit Request Owners Insurance Premium Credit Request ONE Year Limited Warranty Page Page ÀN7003-1V2ä