Filling the Water Heater, Wiring, Acaution

Installation Instructions (cont'd)

Filling the Water Heater

A CAUTION

Never use this water heater unless it is completely filed with water. To prevent damage to the tank, the tank must be filled with water. Water must flow from the hot water faucet before turn ng ON' gas to the water heater.

You must provide all wiring of the proper size outside of the water heater. You must obey local codes and electric company requirements when you install this wiring.

If you are not familiar with electric codes and practices, or if you have any doubt, even the slightest doubt, in your ability to con- nect the wiring to this water heater, obtain the service of a com- petent electrician or contact your local electric utility.

To flU the water heater with water:

Close the water heater drain valve by turning the handle to

the right (clockwise), The drain valve is on the lower front of the water heater.

Open the cold water supply valve to the water heater.

NOTE: The cold water supply valve must be left open when the water heater is in use.

•To insure complete filling of the tank, allow air to exit by

opening the nearest hot water faucet. Allow water to run until a constant flow is obtained. This will let air out of the

water heater and the piping.

•Check all new water piping for leaks. Repair as needed.

Wiring

USE WITH POWER CORD

The water heater comes equipped with a 5 foot power cord which can he used to connect to a 110/120 volt power source if,

(1)local codes allow, and (2) there is a three prong receptacle available.

	\\	5'MAXIMUM
	\N	5'MAXIMUM
	\N	CORD LENGTH
	\%	CORD LENGTH
	\%
	\\
	\\
	\\

AWARNING

WATER HEATERS EQUIPPED FOR ONE TYPE VOLTAGE

ONLY: This water heater is equipped for 110/120 volts only. DO NOT USE THIS WATER HEATER WITH ANY VOLTAGE OTHER THAN THE ONE SHOWN ABOVE. Failure to use the correct voltage can cause problems which can result in DEATH, SERIOUS BODILY INJURY OR PROPERTY DAMAGE. If you haveany questionsor doubts consultyour electric company.

ACAUTION

If wiring from the fuse box or circuit breaker box was alu- minum for the old water heater, replace it with copper wire. If you wish to reuse the existing aluminum wire, have the connection at the water heater made by a competent elec- trician. Contact a local electrical contractor and/or the local electric utility.

USE WITHOUT POWER CORD

If power cord cannot be used, then follow these wiring instruc- tions.

1.Provide a way to easily shut off the electric power when work- ing on the water heater. This could be with a circuit breaker or fuse block in the entrance box or a separate disconnect switch.

2.Install and connect a circuit directly from the main fuse or circuit breaker box. This circuit must be the right size and have its own fuse or circuit breaker.

You must provide all wiring, (1) to a receptacle or, (2) between

the water heater and junction box when the power cord is not used.

GROUND SCREW

AWARNING[

Do not usean extensioncord.If there isnot a suitablerecepta-J cleand/orlocalcedespmhibit useof a powercord,fieldwiring

must be provded.

153.335862, 153.335942, 153.335916, 153.335962, 153.335845 specifications

The Kenmore 153 series, comprising models 153.335916, 153.335942, 153.335962, 153.335845, and 153.335862, is renowned for its innovative design and exceptional performance in household appliances. These models are predominantly known for their washing machines and dryers, which have become staples in modern homes.

One of the standout features of the Kenmore 153 series is its advanced wash technology. Each model incorporates a high-efficiency system designed to reduce water consumption while maximizing cleaning power. The patented triple-action agitator ensures thorough cleaning by moving clothes in multiple directions, providing better agitation and fabric care. This technology not only ensures a deeper clean but also helps in preserving the integrity of fabrics over time.

Energy efficiency is another hallmark of the Kenmore 153 series. Many models are ENERGY STAR certified, which means they meet stringent energy efficiency guidelines set by the U.S. Environmental Protection Agency and the Department of Energy. This leads to significant cost savings over time, making them a smart choice for eco-conscious consumers looking to reduce their environmental footprint.

The Kenmore 153 series also emphasizes user-friendly features. With intuitive control panels and easy-to-read displays, these machines make laundry tasks simpler. Some models include a variety of customizable wash cycles, allowing users to select the optimal settings for different types of fabrics and soil levels. The quick wash and dryer cycles are particularly beneficial for those with busy lifestyles, reducing the time spent on laundry.

Noise reduction technology is another advantage. The Kenmore 153 series is designed with sound-dampening materials and features that minimize operational noise, making them ideal for homes where quiet is preferred, such as during nighttime laundry routines.

In terms of build quality, these models are constructed with durable materials aimed at longevity and reliability. Users can expect years of dependable service, with many designs offering warranties to back their durability claims.

In conclusion, the Kenmore 153 series, including models 153.335916, 153.335942, 153.335962, 153.335845, and 153.335862, encapsulates a blend of advanced laundry technologies, energy efficiency, user-friendly features, and robust build quality. These attributes make them a valuable addition to any household, simplifying the laundry process while delivering excellent results.