Kenmore 153.335942 Installation Instructions contd, Venting Clearances, Property Damage

Page 10

Installation Instructions (cont'd)

AWARNING

A gas water heater cannot operate properly without the cor- rect amount of air for combustion. Do not install in a con-

fined area such a closet, unless you provide air as shown in the "Locating The New Water Heater" section. Never obstruct the flow of ventilation air. If you have any doubts or questions at all, call your gas company. Failure to provide the

proper amount of combustion air can result in a fire or explo- sion and can cause DEATH, SERIOUS BODILY INJURY, OR

PROPERTY DAMAGE.

_,WARNING

If this water heater will be used in beauty shops, barber shops, cleaning establishments, or self-service laundries with dry cleaning equipment, it is imperative that the water heater or water heaters be installed so that combustion and ventilation

air be taken from outside these areas. Refer to the "Locating The New Water Heater" section of this manual and also the

latest edition of the National Fuel Gas Cede, ANSI Z223.1, also

referred to as NFPA 54 for specifics provided concerning air required.

Combustion Air and Ventilation

When determining the installation location for apower vent

water heater, snow accumulation and drifting shouldbe consid- ered in areas where applicable.

VENTING CLEARANCES

•0" clearance for 3" PVC, ABS or CPVC Schedule 40 vent piping from combustible surfaces.

•12" m'n'mum from the ground, 9" ceiling overhangs. Figure 2.

•The Power Vent outlet terminal shall terminate at least 36" above any forced air inlet located within 10 feet. Figure 3a.

•The Power Vent outlet terminal shall terminate at least 9" below, 9"

horizontally from or 9" above any door, window or gravity air inlet into the building. Figure 3a.

•18" minimum in all directions from any obstruction that may interfere. Figure 3b.

•18" minimum from other gravity or natural appliance outlet vents when directly above or 135 ° to either side of center line. Figure 3c.

•36" minimum from any outlet vents when directly below or 45 ° to either side of center line. Figure 3c.

•36" minimum in all directions from any other forced air appliance outlet vent. Figure 3c.

•The location selection must provide clearances for servicing and proper operation of the water heater. Figure 4.

•Vent termination must not be within 4 feet of any items such as gas meters, gas valves or other gas regulating equipment.

•The venting system must be installed in a manner which allows inspection of the installation of the venting pipes and joints as well

as periodic inspection after installation as required by ANSI Standards.

_,WARNING

Vent terminationmustnot be within4 feet of any items suchas gasmeters,gasvalvesor other gasregulating equipment.

" rain from

!::?ng

Figure 2 ]

• LESSTHAN

 

 

 

 

 

 

120"

TERMINAL 12" rain.

 

 

 

 

AIR

 

 

 

 

 

 

 

 

 

 

 

 

INLET

Figure 3a I

 

 

 

 

 

 

 

 

 

VENT TERMINAL

 

 

 

 

 

 

18" TO WALL OR OTHER

 

 

I_

18"

NIN.

 

OBSTRUCTIONS THAT

 

 

 

MAY INTERFERE WITH

 

 

 

 

 

 

 

 

 

 

 

 

VENTING•

 

 

 

 

 

s

VENT TERMINAL

IFigure3'i

 

CORNER OF BUILDING

 

 

 

 

 

POWER VENT TERMINAL

_

. _

-..

\

*THIS DIMENSION IS

 

 

 

 

 

 

iNCREASED TO 36" WHEN

......

 

 

_

 

_

THE VENT OUTLET IS FOR A

Z_

----

__

 

 

 

FORCED VENT APPLIANCE

:-

_ _'_.

_ _8"(:,':i=,:,o_.:,

_S

 

'--_-

_(

'3¥

- DIRECT VENT OR

 

_': _Z

GRAVITY VENTED

__

36';

_

_

 

_APPLIANCE

\

_-ANY OTHER OUTLET VENT

Must maintain

adequate service

and maintenance

_

accessibility.

• l' i

_,WARNING

]

 

 

_L_._

 

Range of degrees

Failureto haverequiredclearancesbetweenwater heater and

 

 

 

 

 

Figure 4

 

 

 

 

combustiblematerialwill resultin a fire hazard.

J

]

"

"

pipe installation.

 

 

 

available for vent

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents What to do if YOU Smell GAS For Your SafetyAN Odorant is Added to the GAS Used by this Water Heater Model NoSafety Precautions Awarning AwarningAGE Safety Precautions Must be propContents Product Specifications Customer ResponsibilitiesMaterials Needed When Sweat SolderingMaterials and Basic Tools Needed Basic ToolsInstallation Instructions Removing the Old Water HeaterLocating the New Water Heater Installation InstructionsOr Property Damage Combustiblematerialwill resultin a fire hazard Installation Instructions contdVenting Clearances Property DamageENT to Installation Completed Using Sears Installation KIT Water PipingInstallation Instructions contd Temperature-Pressure Relief ValveUSE Without Power Cord WiringUSE with Power Cord Filling the Water HeaterVenting USE Without Power Cord contdWiring Diagram Vent pipe from the water heater must be I/4 inch perHill Venting System Example Installations For ALL ModelsVenting contd PVC Schedule 40 Vent PipingVenting System Example Installations for ALL Models contd PrecautionsInstallation Showing USE of PVC, ABS or Cpvc Pipe Connecting PVC, ABS or Cpvc Pipe Vent to BlowerScEw He appliance and its gas connection must be leak tested GAS Piping with Flexible ConnectorGas Piping Sediment TrapBefore Lighting the Pilot Installation ChecklistTemperature Model Rating PlateOperating Instructions Before the Water Heater will OperateLighting Before Lighting Propane L,P. GAS WaterWhatto Doif Yousmellgas Operating Instructions contdTHERMOCOUPLEP,LOTBURNER Temperature Regulation Service and Adjustment Temperature-Pressure Relief Service and Adjustment contdGas Control Valve & Burner Assembly Replacement Information DrainingHousekeeping Drain Valve Washer ReplacementService WasherStart Up Conditions Troubleshooting GuideThermal Expansion SMOKE/ODOR Troubleshooting Guide contdCondensation Smelly WaterAIR in HOT Water Faucets High Temperature Shut OFF SystemOperational Conditions contd Not Enough or no HOT WaterTroubleshooting Guide contd Leakage CheckpointsThermostat and GAS Supply Check IwarningiDiagram for Electrical System Check on pages 34 Swc...,cElectrical System Check Use diagram on Thec#togrouod/r110,I-.- Isindicator,20 o,tshtooI Parts Order List Model NumbersParts Order List contd 153.335816 40 GalPower Miser TM 9 Power Vent GAS Water Heaters Parts Order ListPower Miser TM 9 Power Vent GAS Water Heaters Model Numbers Parts Order List contdWarranty About Your Warranty
Related manuals
Manual 40 pages 985 b

153.335862, 153.335942, 153.335916, 153.335962, 153.335845 specifications

The Kenmore 153 series, comprising models 153.335916, 153.335942, 153.335962, 153.335845, and 153.335862, is renowned for its innovative design and exceptional performance in household appliances. These models are predominantly known for their washing machines and dryers, which have become staples in modern homes.

One of the standout features of the Kenmore 153 series is its advanced wash technology. Each model incorporates a high-efficiency system designed to reduce water consumption while maximizing cleaning power. The patented triple-action agitator ensures thorough cleaning by moving clothes in multiple directions, providing better agitation and fabric care. This technology not only ensures a deeper clean but also helps in preserving the integrity of fabrics over time.

Energy efficiency is another hallmark of the Kenmore 153 series. Many models are ENERGY STAR certified, which means they meet stringent energy efficiency guidelines set by the U.S. Environmental Protection Agency and the Department of Energy. This leads to significant cost savings over time, making them a smart choice for eco-conscious consumers looking to reduce their environmental footprint.

The Kenmore 153 series also emphasizes user-friendly features. With intuitive control panels and easy-to-read displays, these machines make laundry tasks simpler. Some models include a variety of customizable wash cycles, allowing users to select the optimal settings for different types of fabrics and soil levels. The quick wash and dryer cycles are particularly beneficial for those with busy lifestyles, reducing the time spent on laundry.

Noise reduction technology is another advantage. The Kenmore 153 series is designed with sound-dampening materials and features that minimize operational noise, making them ideal for homes where quiet is preferred, such as during nighttime laundry routines.

In terms of build quality, these models are constructed with durable materials aimed at longevity and reliability. Users can expect years of dependable service, with many designs offering warranties to back their durability claims.

In conclusion, the Kenmore 153 series, including models 153.335916, 153.335942, 153.335962, 153.335845, and 153.335862, encapsulates a blend of advanced laundry technologies, energy efficiency, user-friendly features, and robust build quality. These attributes make them a valuable addition to any household, simplifying the laundry process while delivering excellent results.
Top Page Image Contents