Kenmore 153.335862, 153.335942 Installation Instructions, Removing the Old Water Heater

Page 8

Installation Instructions

Removing the Old Water Heater

Turn "OFF" the gas supply to the water heater.

•,WARNING]

If the main gas line shutoff serving all gas appliances is/ used, also shut "off" the gas at each appliance. Leave all gasappliances shut "off" until the water heater installation

s comp ete.

®

QTurn

"OFF"

the

water

to

the

water

heater. Some

installations

require

that

the water be turned off to the entire house.

@

QCheck again to make sure the gas supply is "OFF" to the water heater. Then dis-

connect the gas supply connection from the gas control valve.

QAttach a hose to the water heater drain valve and put the other end in a floor drain or outdoors. Open the water heater drain valve. Open a nearby hot water faucet which will relieve pressure in the water heater and speed draining.

Disconnect the vent pipe from the draft hood where they connect to the water heater. In most installations the vent pipe can be lifted off after any screw or other

attached devices are removed. Dispose of the draft hood. The new water heater has the draft hood which

must be used for proper operation.

If you have copper piping to the water

Q

a.

 

 

 

 

 

 

heater, the two copper water pipes can

 

be cut with a hacksaw approximately

 

four inches away from where they con-

 

nect to the water heater. This will avoid

 

cutting

off the

pipes

too short.

©

Additional cuts can be made later if nec-

essary. Disconnect the temperature-pres-

sure relief

valve

drain

line.

When

the

 

water heater is drained,

disconnect

the

 

hose from the drain valve. Close the

 

drain valve. The water heater is now

completely disconnected and ready to be removed.

Qh. If you have galvanized pipe to the water

heater, loosen the two galvanized pipes with a pipe wrench at the union in each line. Also disconnect the piping remain- ing to the water heater. These pieces should be saved since they may be need-

ed when reconnecting the new water heater. Disconnect the temperature-pres- sure relief valve drain line. When the water heater is drained, disconnect the hose from the drain valve. Close the drain valve. The water heater is now

completely disconnected and ready to be removed.

_WARNING-_

The water passing out of the drain valve may be extremely I hot. To avoid being scalded, make sure all connections are I tight and that the water flow is directed away from any I

person.

ACAUTION

Mineral buildup or sediment may have accumulated in the old water beater. This causes the water heater to be much heavier than normal and this residue, if spilled out, could cause staining.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents For Your Safety AN Odorant is Added to the GAS Used by this Water HeaterWhat to do if YOU Smell GAS Model NoSafety Precautions AGE AwarningAwarning Safety Precautions Must be propContents Product Specifications Customer ResponsibilitiesWhen Sweat Soldering Materials and Basic Tools NeededMaterials Needed Basic ToolsInstallation Instructions Removing the Old Water HeaterOr Property Damage Installation InstructionsLocating the New Water Heater Installation Instructions contd Venting ClearancesCombustiblematerialwill resultin a fire hazard Property DamageENT to Installation Completed Using Sears Installation KIT Water PipingInstallation Instructions contd Temperature-Pressure Relief ValveWiring USE with Power CordUSE Without Power Cord Filling the Water HeaterUSE Without Power Cord contd Wiring DiagramVenting Vent pipe from the water heater must be I/4 inch perVenting System Example Installations For ALL Models Venting contdHill PVC Schedule 40 Vent PipingVenting System Example Installations for ALL Models contd PrecautionsScEw Connecting PVC, ABS or Cpvc Pipe Vent to BlowerInstallation Showing USE of PVC, ABS or Cpvc Pipe GAS Piping with Flexible Connector Gas PipingHe appliance and its gas connection must be leak tested Sediment TrapInstallation Checklist TemperatureBefore Lighting the Pilot Model Rating PlateOperating Instructions Before the Water Heater will OperateLighting Before Lighting Propane L,P. GAS WaterTHERMOCOUPLEP,LOTBURNER Operating Instructions contdWhatto Doif Yousmellgas Temperature Regulation Service and Adjustment Service and Adjustment contd Gas Control Valve & Burner Assembly Replacement InformationTemperature-Pressure Relief DrainingDrain Valve Washer Replacement ServiceHousekeeping WasherThermal Expansion Troubleshooting GuideStart Up Conditions Troubleshooting Guide contd CondensationSMOKE/ODOR Smelly WaterHigh Temperature Shut OFF System Operational Conditions contdAIR in HOT Water Faucets Not Enough or no HOT WaterTroubleshooting Guide contd Leakage CheckpointsThermostat and GAS Supply Check IwarningiDiagram for Electrical System Check on pages 34 Swc...,cElectrical System Check Use diagram on Thec#togrouod/r110,I-.- Isindicator,20 o,tshtooI Parts Order List Model NumbersParts Order List contd 153.335816 40 GalPower Miser TM 9 Power Vent GAS Water Heaters Parts Order ListPower Miser TM 9 Power Vent GAS Water Heaters Model Numbers Parts Order List contdWarranty About Your Warranty
Related manuals
Manual 40 pages 985 b

153.335862, 153.335942, 153.335916, 153.335962, 153.335845 specifications

The Kenmore 153 series, comprising models 153.335916, 153.335942, 153.335962, 153.335845, and 153.335862, is renowned for its innovative design and exceptional performance in household appliances. These models are predominantly known for their washing machines and dryers, which have become staples in modern homes.

One of the standout features of the Kenmore 153 series is its advanced wash technology. Each model incorporates a high-efficiency system designed to reduce water consumption while maximizing cleaning power. The patented triple-action agitator ensures thorough cleaning by moving clothes in multiple directions, providing better agitation and fabric care. This technology not only ensures a deeper clean but also helps in preserving the integrity of fabrics over time.

Energy efficiency is another hallmark of the Kenmore 153 series. Many models are ENERGY STAR certified, which means they meet stringent energy efficiency guidelines set by the U.S. Environmental Protection Agency and the Department of Energy. This leads to significant cost savings over time, making them a smart choice for eco-conscious consumers looking to reduce their environmental footprint.

The Kenmore 153 series also emphasizes user-friendly features. With intuitive control panels and easy-to-read displays, these machines make laundry tasks simpler. Some models include a variety of customizable wash cycles, allowing users to select the optimal settings for different types of fabrics and soil levels. The quick wash and dryer cycles are particularly beneficial for those with busy lifestyles, reducing the time spent on laundry.

Noise reduction technology is another advantage. The Kenmore 153 series is designed with sound-dampening materials and features that minimize operational noise, making them ideal for homes where quiet is preferred, such as during nighttime laundry routines.

In terms of build quality, these models are constructed with durable materials aimed at longevity and reliability. Users can expect years of dependable service, with many designs offering warranties to back their durability claims.

In conclusion, the Kenmore 153 series, including models 153.335916, 153.335942, 153.335962, 153.335845, and 153.335862, encapsulates a blend of advanced laundry technologies, energy efficiency, user-friendly features, and robust build quality. These attributes make them a valuable addition to any household, simplifying the laundry process while delivering excellent results.
Top Page Image Contents