Kenmore 153.33439, 153.33459, 153.33449, 153.33429 owner manual Venting contd, Gas Piping

Page 14

Installation Instructions (cont'd)

Venting (cont'd)

All vent gases must be completely vented to the outdoors of the structure (dwelliNg). Installonly the draft hood provided with the new water heater and no other draft hood.

Vent pipes must be secured at each joint with sheet metal s_rews.

TO

CHIMNEY

I

. RISE'PER LINEARo NEAR

i!

VENT PIPE INSTALLATION

There must be a minimum of 6" clearance between single wall vent pipe and any combustible material. Fill and seal any clear-

ance between single wall vent pipe and combustible material with mortar mix, cement, or other noncombustible substance.

For other than single wall, follow vent pipe manufacturer's clear- ance specifications. To insure a tight fit of the vent pipe in a

brick chimney, seal around the vent pipe with mortar mix cement.

_,WARNING

Failureto have _lui_l dearancesbetween vent pipingand combustiblematerialwill result in a fire hazard.

_,WARNING[

Be sure vent pipe isproperly connectedto preventescapeof [

dangerousfluegaseswhichcouldcausedeadlyasphyxiation. [

Gas Piping

&WARNING

Make sure the gas suppliedis the same type listed on the modal rating plate. The inlet gaspressuremust not exceed 14 incheswater column ½ poundper squareinch (3.SkPa). The minimum inlet gas pressurelistedon the model rating plate isfor the purposeof inputadjustment.

AWARNING

. , [

If the gascontrol valveissubjectedto pressuresexceedng½ [ pound per square inch (3.5kPa),the damageto the.gascon- trol valvecouldresultin a fire or explosionfrom eaidngga_

&WARNING

If the main gasline shutoffservingall gasappliancesis used,[ alsoturn "OFF" the gasat eachappliance.Leaveall gasappli- ancesshut offunti the water heaterinstallationiscon_ete.

A gas line of sufficient size must be run to the water heater. Consult the latest edition of National Fuel Gas Code ANSI

Z223.1, also referred to as NFPA54 and the gas company concern- ing pipe size.

There must be:

•A readily accessiblemanual shut offvalve in the gas supply line serving the water heater, and

•A drip leg (sediment trap) ahead of the gas control valve to help

prevent dirt and foreign materials from entering the gas control

valve.

•A flexible gas connector or a ground joint union between the shuroffvalve and control valve to permit servicing of the unit.

Be sure to check all the gas piping for leaks before lighting the water heater. Use a soapy water solution, not a match or open

flame. Rinse offsoapy solution and wipe dry.

AWARNING

Chemical vapor corrosionof the flue and vent system may occurif air for combustioncontainscertain chemicalvapors. Spray can propellants,cleaningsolvents,refrigerator and air conditioner refrigerants,swimming pool chemicals,calcium and sodiumchloride,waxes,blench,and processchemicalsare typicalcompoundswhichare potentially corrosive.

Standard Models are for installation up to 3,300 feet above sea level.

High Altitude Models are for installation from 3,300 to 5,500 feet above sea level.

lfa standard model is installed above 3,300 feet or a high altitude model is installed above 5,500 feet, the input rating must be reduced at the rate of 4 percent for each 1,000 feet above sea level.

Contact your local Sears Service Center or gas utility for further information.

&WARNING

The appliance and its gas connection must be leak tested beforeplacingthe appliancein operation.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model No For Your SafetyWhat to do if YOU Smell GAS Odorant is Added to the GAS Used by this Inat E R HeaterDEATH, Serious Bodily INJURY, or Property Safety PrecautionsWater Heaters Equipped for ONE Type GAS Safety Precautions Safety Precautions Contents Customer RespOnsibilities SpecificationsProduct @ 90F RiseBasic Tools Materials and Basic Tools NeededMaterials Needed Cut with a hacksaw approximately Installation InstructionsRemoving the Old Water Heater DEATH,SERIOUSBODILYINJUR,OR Propertydamage Installation Instructions contdFacts to Consider About Location Installation Instructions contd ALL AIR from Inside BuildingsWater Piping AE,WARNINGTemperature-Pressure Relief Valve PpeFilling the Water Heater VentingVenting contd Gas PipingAwarning GAS Piping with Flexible ConnectorContd Sediment TrapModel Rating Plate Installation ChecklistBefore Lighting the Pilot Check for Leaks Operating InstructionsLighting Before Lighting Propane LP. GAS WaterControlsystemand any gas controlwhichhas been underwater Operating Instructions contdWhatto Doif Yousmellgas Not ForceHotter Water can SCALDWater heatersareintendedto Temperature RegulationHOT-Is a thermostat setting of approximately Canscaldand permanentlyinjureyouuponcontact.SomepeoBurner Cleaning Service and AdjustmentTank Sediment Cleaning Burner InspectionDrain Valve Washer Replacement Service and Adjustment contdTemperature-Pressure Relief Condensation Troubleshooting GuideStart Up Conditions Thermal ExpansionAIR in HOT Water Faucets Troubleshooting Guide contdStrange Sounds Smelly WaterNot Enough or no HOT Water High Temperature Shut OFF SystemContd Water is TOO HOTLeakage Checkpoints AcautionParts Order List Parts Order List contd Lightingpilot Warranty8OO-4.MY-HOME

153.33429, 153.33439, 153.33449, 153.33459 specifications

The Kenmore 153 series offers a range of powerful and versatile upright vacuums, specifically models 153.33439, 153.33459, 153.33429, and 153.33449. Each model presents unique features that cater to diverse cleaning needs, making them appealing choices for households seeking efficient cleaning solutions.

All models in the Kenmore 153 series are equipped with a robust motor that delivers strong suction power, allowing them to pick up dirt, debris, and pet hair with ease. The high-performance design ensures that even embedded dirt in carpets is effectively removed. Additionally, these vacuums come with a multi-surface cleaning capability, making them suitable for various floor types, including carpets, hardwoods, and tiles.

One of the standout technologies in the Kenmore 153 series is the advanced filtration system. Each vacuum is fitted with a HEPA filter that captures 99.97% of dust and allergens as small as 0.3 microns. This feature is particularly advantageous for allergy sufferers, ensuring cleaner air and a healthier living environment.

The vacuums also boast a user-friendly design, featuring a lightweight body that enhances maneuverability. The swivel steering allows users to navigate around furniture easily, while the telescoping wand extends for reach in hard-to-access areas, such as ceilings and corners. The convenient dusting brush and upholstery tool make the cleaning process seamless, ensuring no corner of the home is left untouched.

Another attractive aspect of the Kenmore 153 series is their noise-reduction technologies. The "quiet mode" feature allows for efficient cleaning without disturbing the household, making them ideal for any time of day, whether it's during nap times or late at night.

The sturdy construction of these vacuums ensures durability and longevity, paired with a sleek modern design that fits well within any home aesthetic. Each model offers adjustable height settings, allowing users to adapt the vacuum according to their cleaning preferences and the type of flooring being cleaned.

In summary, the Kenmore 153 series, featuring models 153.33439, 153.33459, 153.33429, and 153.33449, exemplifies versatility, power, and user-centric design. With their advanced technologies and robust features, these vacuums are well-suited for households looking to maintain cleanliness and improve indoor air quality. The Kenmore 153 series is worth considering for anyone in the market for a reliable vacuum cleaner.
Top Page Image Contents