Kenmore 153.32116, 153.32118 Water Heater Location, Water System Piping, Condensate Drain Line

Page 15

Water Heater Location

[] Centrally located with the water piping system.

[] The flooring beneath the water heater must be able to support the weight of the water heater when filled with water (See Table 1).

[] Located indoors (such as a basement or garage) and in a vertical position. Sheltered from freezing temperatures.

[] Provisions made to shelter the area from water

damage. Metal drain pan installed and piped to an adequate drain.

[] Sufficient room to service the water heater.

[] Sufficient air for the heat pump to function. The water heater must be located in a space 750 cubic feet or

larger, and must have unrestricted airflow. As an example, a room that has an 8 foot tall ceiling and is 10 feet long by 9-1/2 feet wide would contain 760 cubic feet. NOTE: For optimal efficiency and serviceability, the following clearances should be maintained: 3 feet on the air inlet side, 5 feet on the air outlet side, 6 inches in the back, and 2 feet in the front.

[] The unit cannot be placed into any type of closet or small enclosure.

[] The site location must be free from any corrosive elements in the atmosphere such as sulfur, fluorine, and chlorine. These elements are found in aerosol sprays, detergents, bleaches, cleaning solvents, air fresheners, paint, and varnish removers, refrigerants, and many other commercial and household products. In addition excessive dust and lint may affect the operation of the unit and require more frequent cleaning (See "Routine Preventive Maintenance" section).

Ambient air temperature must be above 45°F and below 109°F. If the ambient air temperature falls outside these upper and lower limits the electrical elements will activate to meet the hot water demand.

Water System Piping

[] Temperature and pressure relief valve properly installed with a discharge pipe run to an adequate drain and sheltered from freezing (See Figure 10).

[] All piping properly installed and free of leaks.

[] Heater completely filled with water (See "Water Piping System" section).

[] Closed system pressure buildup precautions installed (See "Closed System/Thermal Expansion" section).

[] Mixing valve (when applicable) installed per manufacturer's instructions (See "Temperature Regulation" section).

Condensate Drain Line

[] Must be located with access to an adequate drain or condensate pump.

[] Condensate drain lines installed and piped to an adequate drain or condensate pump (See Figure 9).

Electrical Connections

[] This water heater requires a 240 VAC single phase 25 amp power supply. DO NOT use a 208 VAC service.

[] Wiring size and connections comply with all applicable codes or in the absence of local or state codes follow NFPA- 70, the National Electrical Code-current edition.

[] Water heater and electrical supply are properly grounded.

[] Wiring enclosed in approved conduit (if required by local codes).

[] Proper overload fuse or circuit breaker protection installed.

Post Installation Review

[] Understand how to use the User Interface Module to set the various modes and functions (See "Adjusting the User Interface Module/Operating Modes" section).

[] Hybrid Mode is the recommended Operating Mode. Understand the various Operating Modes and which mode may be best based on season, ambient temperature, and usage (See "Operating Mode Description" section). NOTE: It may be necessary to temporarily change modes if for example filling a spa or hot tub.

[] Understand the importance of routine inspection/ maintenance of the condensate drain pan and lines

(See "Inspection/Cleaning of the Condensate Drain

Pan & Condensate Drain Lines" section). This is to help prevent any possible drain line blockage resulting in the condensate drain pan overflowing.

IMPORTANT: Water coming from the plastic shroud is an indicator that both condensation drain lines may be blocked. Immediate action is required.

[] To maintain optimal operation check, remove and clean the air filter (See "Air Filter Cleaning/Replacement" section).

[] The Installation Instructions and Use & Care Guide should be kept with the water heater for reference.

15

Image 15
Contents Ienmore Elite Important Definitions Fire Hazard / Electric Shock Hazard Improper installation and use may result in property damageYear Limited Warranty on Water H Eater Safe Installation USE and Service General ThankYouforpurchasingSearswaterheaterProperly Installedandmaintained,itshouldgiveyouyearsoftroublefreeAdditional Tools Needed When Sweat Soldering Materials NeededBasic Tools Removing the Old Water Heater Facts to Consider About the Location Insulation BlanketsWith water SeeClosed System Water Piping System Piping InstallationCondensate Drain Line Installation Valve and Pipe InsulationProperty Damage Hazard Explosion Hazard Temperature-Pressure Relief ValveFilling the Water Heater WiringConnecting the Condensate Pump Overflow Shut Off Switch Wiring DiagramCondensate Drain Line Post Installation ReviewWater Heater Location Water System PipingOperational Modes Before UsingTemperature Regulation Adjusting the User Interface ModuleSet temperature in Fahrenheit or Celsius Operating Mode DescriptionsDraining and Flushing Element Removal/ReplacementAir Filter Cleaning/Replacement Routine Preventive MaintenanceService Drain Valve Washer ReplacementThermal Expansion Tank Specifications Start Up ConditionsOperational Conditions AIR in HOT Water Faucets Display Shows Indicates Problem Installation Instructions section Kenmore Elite Hybrid Electric Heat Pump Water Heaters Page Call anytime, day or night U.S.A. and Canada Managemylife

153.32116, 153.32118 specifications

The Kenmore 153.32118 and 153.32116 are leading models in the realm of water heaters, designed to enhance efficiency and performance while maintaining user-friendliness. Both models cater to the modern consumer's needs for reliable hot water access in residential settings.

One of the standout features of the Kenmore 153.32118 and 153.32116 is their energy-efficient design. Equipped with advanced insulation technology, these heaters maximize heat retention, which minimizes energy loss and contributes to lower utility bills. The units operate on an efficient heating element that quickly raises water temperature, ensuring that users have hot water available whenever they need it.

Both models come with a user-friendly digital display that allows homeowners to easily adjust settings, monitor water temperature, and receive alerts about system performance. This intuitive interface enhances the overall user experience, making it simple for anyone to operate the heater without requiring extensive technical knowledge.

Safety is a top priority in the design of these water heaters. They are equipped with multiple safety features, such as a temperature control mechanism that prevents overheating and a pressure relief valve that mitigates risks associated with excessive pressure build-up. These safety measures ensure peace of mind for the user, knowing that the appliance is designed to operate safely within a home environment.

The Kenmore 153.32118 and 153.32116 models also boast a compact design, allowing them to fit seamlessly into various spaces, whether in a utility room, basement, or closet. The sleek appearance ensures that they can be incorporated into the home without disrupting the aesthetic flow of the environment.

Maintenance is made simple with these units, as they are designed to require minimal attention over time. The self-cleaning feature helps inhibit sediment buildup, which can affect efficiency and longevity. This technology not only extends the lifespan of the heaters but also ensures consistent performance over time.

In conclusion, the Kenmore 153.32118 and 153.32116 represent a blend of efficiency, safety, and modern technology. With their advanced features and user-friendly design, they meet the demands of today’s households for reliable hot water solutions while keeping energy consumption to a minimum. Whether for daily household needs or specialized tasks, these water heaters stand out as robust options in the market.