Kenmore 153.32118, 153.32116 manual AIR in HOT Water Faucets

Page 22

"AIR" IN HOT WATER FAUCETS

Explosion Hazard

• Flammable hydrogen gases may be present.

• Keep all ignition sources away from faucet when turning on hot water.

HYDROGEN GAS: Hydrogen gas can be produced in a hot water system that has not been used for a long period of time (generally two weeks or more). Hydrogen gas is extremely flammable and explosive. To prevent the possibility of injury under these conditions, we recommend the hot water faucet be opened for several minutes at the kitchen sink before any electrical appliances which are connected to the hot water system are used (such as a dishwasher or washing machine).

If a fault is detected by the system, an error message wilt be

displayed on the MAIN screen indicating the general nature of the fault. More detailed fault information can be obtained

by viewing the MAINTENANCE screen. The MAINTENANCE screen is accessed by simultaneously actuating the UP and DOWN arrows on the user interface touch pad for 3 seconds. (Note: engaging the child lock feature will not prevent access to the MAINTENANCE screen, but wilt prevent inadvertent

changing of the set point temperature.) Once the screen changes to MAINTENANCE, use the up arrow to scroll to the error messages. There are six (6) system temperature messages display in succession, followed by four (4) stored

fault messages. Fault messages are stored newest to oldest and are labeled EO1 - EO4. Utilize the DIAGNOSTIC CODES

table for explanation of what each fault message means and corrective action steps for each."

If hydrogen gas is present, there wilt probably be an unusual sound similar to air escaping through the pipe as the hot water faucet is opened. There must be no smoking or open flame near the faucet at the time it is open.

RUMBLING NOISE

In some water areas, scale or mineral deposits wilt build up on your heating elements. This buildup wilt cause a rumbling noise. Follow Element Removal/Replacement instructions to clean and replace the elements.

HIGH TEMPERATURE SHUT OFF SYSTEM

This water heater is designed to automatically shut-off in the event that the water temperature exceeds 190°F or 87.8°C. A temperature limit switch or ECO (Energy Cut Off) is used to shut off the power to the system if the water temperature exceeds 190°F or 87.8°C (See "Water Temperature Regulation" section). To reset the ECO disconnect power at the circuit breaker/fuse box then remove the upper access panel. Reset

the ECO by firmly pushing in the red reset button located on the ECO block. If the ECO continues to shut-off the water heater

contact a qualified person for service.

System temperature parameters are available on the MAINTENANCE screen to aid in assessing the operation of the heat pump. Access the MAINTENANCE screen as described in the preceding paragraph. Scroll through the parameters using the UP and DOWN arrows. The six (6) system temperatures are listed in the following order:

•AMBIENT TEMPERATURE

•TANK TEMPERATURE (average)

•UPPER TANK TEMPERATURE

•LOWER TANK TEMPERATURE

•DISCHARGE TEMPERATURE (compressor discharge)

•COIL TEMPERATURE (evaporator coil outlet)

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Ienmore Elite Important Definitions Improper installation and use may result in property damage Fire Hazard / Electric Shock HazardYear Limited Warranty on Water H Eater Safe Installation USE and Service General Installedandmaintained,itshouldgiveyouyearsoftroublefree ThankYouforpurchasingSearswaterheaterProperlyMaterials Needed Additional Tools Needed When Sweat SolderingBasic Tools Removing the Old Water Heater Insulation Blankets Facts to Consider About the LocationWith water Water Piping System Piping Installation SeeClosed SystemValve and Pipe Insulation Condensate Drain Line InstallationProperty Damage Hazard Temperature-Pressure Relief Valve Explosion HazardWiring Filling the Water HeaterWiring Diagram Connecting the Condensate Pump Overflow Shut Off SwitchWater System Piping Post Installation ReviewWater Heater Location Condensate Drain LineAdjusting the User Interface Module Before UsingTemperature Regulation Operational ModesOperating Mode Descriptions Set temperature in Fahrenheit or CelsiusElement Removal/Replacement Draining and FlushingRoutine Preventive Maintenance Air Filter Cleaning/ReplacementDrain Valve Washer Replacement ServiceStart Up Conditions Thermal Expansion Tank SpecificationsOperational Conditions AIR in HOT Water Faucets Display Shows Indicates Problem Installation Instructions section Kenmore Elite Hybrid Electric Heat Pump Water Heaters Page Managemylife Call anytime, day or night U.S.A. and Canada

153.32116, 153.32118 specifications

The Kenmore 153.32118 and 153.32116 are leading models in the realm of water heaters, designed to enhance efficiency and performance while maintaining user-friendliness. Both models cater to the modern consumer's needs for reliable hot water access in residential settings.

One of the standout features of the Kenmore 153.32118 and 153.32116 is their energy-efficient design. Equipped with advanced insulation technology, these heaters maximize heat retention, which minimizes energy loss and contributes to lower utility bills. The units operate on an efficient heating element that quickly raises water temperature, ensuring that users have hot water available whenever they need it.

Both models come with a user-friendly digital display that allows homeowners to easily adjust settings, monitor water temperature, and receive alerts about system performance. This intuitive interface enhances the overall user experience, making it simple for anyone to operate the heater without requiring extensive technical knowledge.

Safety is a top priority in the design of these water heaters. They are equipped with multiple safety features, such as a temperature control mechanism that prevents overheating and a pressure relief valve that mitigates risks associated with excessive pressure build-up. These safety measures ensure peace of mind for the user, knowing that the appliance is designed to operate safely within a home environment.

The Kenmore 153.32118 and 153.32116 models also boast a compact design, allowing them to fit seamlessly into various spaces, whether in a utility room, basement, or closet. The sleek appearance ensures that they can be incorporated into the home without disrupting the aesthetic flow of the environment.

Maintenance is made simple with these units, as they are designed to require minimal attention over time. The self-cleaning feature helps inhibit sediment buildup, which can affect efficiency and longevity. This technology not only extends the lifespan of the heaters but also ensures consistent performance over time.

In conclusion, the Kenmore 153.32118 and 153.32116 represent a blend of efficiency, safety, and modern technology. With their advanced features and user-friendly design, they meet the demands of today’s households for reliable hot water solutions while keeping energy consumption to a minimum. Whether for daily household needs or specialized tasks, these water heaters stand out as robust options in the market.
Top Page Image Contents