Kenmore 153.32116, 153.32118 manual Routine Preventive Maintenance, Air Filter Cleaning/Replacement

Page 19

1.Press the power button on the user interface module to place the water heater in Standby Mode.

2.Turn off the power to the water heater.

FIGURE 18.

3, Drain the water heater as directed in the "Draining and Flushing" section.

•Burn hazard

•Hotwater discharge.

•Keep hands clear of drain valve discharge.

4, Remove the access cover(s), then remove the foam insulation block.

5.Remove the protective plastic cover(s) over the elements from their attachment point.

6.Disconnect the electrical wires from the heating element(s) by loosening the screws (Figure 19). Remove the screw-in element(s) by turning the element(s) counterclockwise with a 1-1/2 inch socket wrench. Remove the existing gasket(s).

_Wires

/ Element

Screws _

FIGURE 19.

7, Clean the area where the gasket(s) fits to the tank and internal threads. If you are replacing the bottom element, remove any accumulated sediment on the bottom of the tank.

8, If you are cleaning the element you have removed, do so by scraping or soaking in vinegar or a de-liming solution.

9.Make sure the replacement element(s) has the correct

voltage and wattage rating by matching itto the rating ptate on the water heater. Position the new gasket(s) on the element

and insert it into the water heater tank (Figure 20). NOTE: Apply a light coat of hand dishwashing soap and water to the gasket. Tighten the element by turning it clockwise until secure.

Screw-in

Element_

Gasket_

FIGURE 20.

10.Close the drain valve and open the nearest hot water faucet. Then open the cold water shut off valve and allow the tank to fill completely with water. To purge the lines of any excess air and sediment, keep the hot water

faucet open for 3 minutes after a constant flow of water is obtained.

11.Check for leaks around the element(s).

12.Reconnect the electrical wires to the element and securely tighten the screws (See Figure 19).

13.Replace the protective plastic cover(s) removed earlier. Make sure the cover(s) are securely engaged on the attachment point(s).

14.Replace the foam block(s) and access cover(s).

15.Although this water heater is equipped with "Dry Fire" protection circuitry, be sure tank is completely filled with water before applying electrical power to the water heater.

16.Reconnect electrical power to the water heater at the circuit breaker/fuse box.

17.Press the power button to turn the water heater on. Set the desired water temperature and operating mode. NOTE: The water heater wilt conduct a system diagnostic check (approximately 8 minutes) prior to operation.

Routine Preventive Maintenance

At least monthly, a visual inspection should be made of the following:

•Air Filter (Remove and inspect, clean if needed, and reinstall).

•Condensate drain pan and condensate lines.

•The lower metal drain pan for standing water which may indicate a clogged condensate drain pan, condensate lines, or plumbing leak.

•Leaking or damaged water piping.

•Presence of corrosive materials in the installation area.

•Presence of combustible materials near the water heater.

IMPORTANT: If you tack the necessary skills required to properly perform this visual inspection, you should not proceed, but get help from a qualified person.

Air Filter Cleaning/Replacement

IMPORTANT: Before attempting to clean or replace the air filter press the power button to place the water heater in Standby Mode and turn-off power to the water heater at the circuit breaker/fuse box.

1.Locate the screw securing the filter panel to the heat pump shroud and loosen it.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Ienmore Elite Important Definitions Fire Hazard / Electric Shock Hazard Improper installation and use may result in property damageYear Limited Warranty on Water H Eater Safe Installation USE and Service General ThankYouforpurchasingSearswaterheaterProperly Installedandmaintained,itshouldgiveyouyearsoftroublefreeMaterials Needed Additional Tools Needed When Sweat SolderingBasic Tools Removing the Old Water Heater Insulation Blankets Facts to Consider About the LocationWith water SeeClosed System Water Piping System Piping InstallationValve and Pipe Insulation Condensate Drain Line InstallationProperty Damage Hazard Explosion Hazard Temperature-Pressure Relief ValveFilling the Water Heater WiringConnecting the Condensate Pump Overflow Shut Off Switch Wiring DiagramCondensate Drain Line Post Installation ReviewWater Heater Location Water System PipingOperational Modes Before UsingTemperature Regulation Adjusting the User Interface ModuleSet temperature in Fahrenheit or Celsius Operating Mode DescriptionsDraining and Flushing Element Removal/ReplacementAir Filter Cleaning/Replacement Routine Preventive MaintenanceService Drain Valve Washer ReplacementStart Up Conditions Thermal Expansion Tank SpecificationsOperational Conditions AIR in HOT Water Faucets Display Shows Indicates Problem Installation Instructions section Kenmore Elite Hybrid Electric Heat Pump Water Heaters Page Call anytime, day or night U.S.A. and Canada Managemylife

153.32116, 153.32118 specifications

The Kenmore 153.32118 and 153.32116 are leading models in the realm of water heaters, designed to enhance efficiency and performance while maintaining user-friendliness. Both models cater to the modern consumer's needs for reliable hot water access in residential settings.

One of the standout features of the Kenmore 153.32118 and 153.32116 is their energy-efficient design. Equipped with advanced insulation technology, these heaters maximize heat retention, which minimizes energy loss and contributes to lower utility bills. The units operate on an efficient heating element that quickly raises water temperature, ensuring that users have hot water available whenever they need it.

Both models come with a user-friendly digital display that allows homeowners to easily adjust settings, monitor water temperature, and receive alerts about system performance. This intuitive interface enhances the overall user experience, making it simple for anyone to operate the heater without requiring extensive technical knowledge.

Safety is a top priority in the design of these water heaters. They are equipped with multiple safety features, such as a temperature control mechanism that prevents overheating and a pressure relief valve that mitigates risks associated with excessive pressure build-up. These safety measures ensure peace of mind for the user, knowing that the appliance is designed to operate safely within a home environment.

The Kenmore 153.32118 and 153.32116 models also boast a compact design, allowing them to fit seamlessly into various spaces, whether in a utility room, basement, or closet. The sleek appearance ensures that they can be incorporated into the home without disrupting the aesthetic flow of the environment.

Maintenance is made simple with these units, as they are designed to require minimal attention over time. The self-cleaning feature helps inhibit sediment buildup, which can affect efficiency and longevity. This technology not only extends the lifespan of the heaters but also ensures consistent performance over time.

In conclusion, the Kenmore 153.32118 and 153.32116 represent a blend of efficiency, safety, and modern technology. With their advanced features and user-friendly design, they meet the demands of today’s households for reliable hot water solutions while keeping energy consumption to a minimum. Whether for daily household needs or specialized tasks, these water heaters stand out as robust options in the market.
Top Page Image Contents