ThankYouforpurchasingSearswaterheaterProperly

ThankYouforpurchasingSearswaterheaterProperly.

installedandmaintained,itshouldgiveyouyearsoftroublefree

serviceItisstronglysuggestedthatthisnewwaterheaterbe.

professionallyinstalled,contactthelocalSearsServiceCenteror

anySearsstoreTheywiltarrangeforprompt,qualityinstallation.

bySearsauthorizedcontractors.

Abbreviations Found In This Instruction Manual:

UL- Underwriters Laboratories Inc.

NEC - National Electrical Code

ANSI-American National Standards Institute

•Read the General Safety section, page 3 of this manual first and then the entire manual carefully. If you don'tfollow the safety rules, the water heater will not operate properly. It could cause DEATH, SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE.

This manual contains instructions for the installation, operation, and maintenance of this electric water heater. It also contains warnings throughout the manual that you must read and be aware of. All warnings and all instructions are essential to the proper operation of the water heater and your

safety. Since we cannot put everything on the first few pages,

READ THIS ENTIRE MANUAL BEFORE ATTEMPTING TO INSTALL OR OPERATE THE WATER HEATER.

•The installation must conform with the instructions in this manual; electric company rules; and Local Codes, or in

heat pump water heater unit, having an 850 Watt compressor and an external coil heat exchanger with backup electric elements.

When in Efficiency Mode the heat pump draws heat from the ambient air in the room and transfers it to the water in the tank

through the coil heat exchanger. While in Electric Mode the water heater functions like a standard electric water heater, relying on the electric elements to heat the water. A Hybrid Mode is available that relies primarily on the heat pump to heat the water while the electric elements only function during high demand periods. The more often the unit operates using the heat pump, rather than the elements, the more efficient the unit wilt be.

The large tank capacities of the Kenmore Elite Hybrid Electric Water Heaters are intended to take optimal advantage of the heat pump's capability to heat water for large families or those having higher than normal hot water requirements. The larger capacities enable the units to operate in the maximum efficiency mode more often than other models having lower capacities.

These Electric Heat Pump Water Heaters use about half the electricity of a comparably sized conventional electric water heater when operating in the Efficiency Mode and provide up to 1/2 ton cooling capacity and dehumidification. They are designed for indoor, residential applications for installation in a basement, garage or utility room.

theabsenceofLocalCodes,withthecurrenteditionofthe

NEC - National Electrical Code, NFPA 70. This publication is available from your local government or public library or electric company or by writing Underwriters Laboratories Inc., 333 Pfingsten Road, Northbrook, IL 60062.

If after reading this manual you have any questions or do not understand any portion of the instructions, call Sears Service Center.

Carefully plan the place where you are going to put the water heater. Correct electrical wiring and connections are very important in preventing death from possible electrical shock and fires.

Examine the location to ensure the water heater complies with the Facts to Consider About the Location section.

For California installation, this water heater must be braced, anchored, or strapped to avoid falling or moving during an earthquake. See instructions for correct installation procedures. Instructions may be obtained from California's Office of the State Architect, 1102 Q Street, Suite 5100, Sacramento, CA95811. Instructions can also be downloaded to your computer at www.dsa.dgs.ca.gov/Pubs.

Massachusetts Code requires this water heater to be installed in accordance with Massachusetts 248-CMR 2.00; State Plumbing Code and 248-CMR 5.00. In the Commonwealth of Massachusetts, this product must be installed by a licensed plumber or gasfitter.

Ambient	Air		Cool/Dehumidified Air
	Heat	Pump
	(Transfers heat		_
	from ambient		_
	air to	Heat
	Exchanger)		_
Upper Element			jWater	Tank
			jWater	Tank
(4500	Watt)

Jacket

Heat Exchanger

(Heat Transfer Coils)

Lower Element

(2000 Watt)

FIGURE 1.

DIMENSIONS

IN INCHES

RECOVERY

MINIMUM

FUSE

TANK

RATE GALS.

OR CIRCUIT

(mm)

MODEL

CAPACITY

PER HOUR @

ELEMENT WATTAGE

MINIMUM WIRE

BREAKER

SIZE

NUMBER

GALLONS

DIA.

HEIGHT

90°F RISE

@ 240 VOLTS

SIZE* (GAUGE)

(AMPS)

153.321160

24 (610)

67.3

(1709)

20.7**

4500

Upper/2000

Lower

10AWG

153.321180

24 (610)

80.9

(2055)

20.7**

4500

Upper/2000

Lower

10AWG

*Wiring size based on standard 60°C copper wire. If distance from fuse box to water heater is more than 90 feet, refer to your local electrical code.

**Actual recovery will differ under Efficiency and Hybrid modes based upon ambient temperature, humidity, and other environmental factors.

153.32116, 153.32118 specifications

The Kenmore 153.32118 and 153.32116 are leading models in the realm of water heaters, designed to enhance efficiency and performance while maintaining user-friendliness. Both models cater to the modern consumer's needs for reliable hot water access in residential settings.

One of the standout features of the Kenmore 153.32118 and 153.32116 is their energy-efficient design. Equipped with advanced insulation technology, these heaters maximize heat retention, which minimizes energy loss and contributes to lower utility bills. The units operate on an efficient heating element that quickly raises water temperature, ensuring that users have hot water available whenever they need it.

Both models come with a user-friendly digital display that allows homeowners to easily adjust settings, monitor water temperature, and receive alerts about system performance. This intuitive interface enhances the overall user experience, making it simple for anyone to operate the heater without requiring extensive technical knowledge.

Safety is a top priority in the design of these water heaters. They are equipped with multiple safety features, such as a temperature control mechanism that prevents overheating and a pressure relief valve that mitigates risks associated with excessive pressure build-up. These safety measures ensure peace of mind for the user, knowing that the appliance is designed to operate safely within a home environment.

The Kenmore 153.32118 and 153.32116 models also boast a compact design, allowing them to fit seamlessly into various spaces, whether in a utility room, basement, or closet. The sleek appearance ensures that they can be incorporated into the home without disrupting the aesthetic flow of the environment.

Maintenance is made simple with these units, as they are designed to require minimal attention over time. The self-cleaning feature helps inhibit sediment buildup, which can affect efficiency and longevity. This technology not only extends the lifespan of the heaters but also ensures consistent performance over time.

In conclusion, the Kenmore 153.32118 and 153.32116 represent a blend of efficiency, safety, and modern technology. With their advanced features and user-friendly design, they meet the demands of today’s households for reliable hot water solutions while keeping energy consumption to a minimum. Whether for daily household needs or specialized tasks, these water heaters stand out as robust options in the market.