Kenmore 153.32118, 153.32116 manual Draining and Flushing, Element Removal/Replacement

Page 18

If after manually operating the valve, it fails to completely reset and continues to release water, immediately close the cold water inlet to the water heater, follow the draining instructions, and replace the temperature-pressure relief valve with a new one.

Failure to install and maintain a new properly listed temperature- pressure relief valve wilt release the manufacturer from any claim which might result from excessive temperature or pressure.

If the temperature-pressure relief valve on the appliance weeps or discharges periodically, this may be due to thermal expansion. Your water heater may have a check valve installed in the water line or a water meter with a check valve. Consult your local Sears Service Center for further information. Do not plug the temperature-pressure relief valve.

Draining and Flushing

W I,7-4 qtW

•Burn hazard

•Hotwater discharge.

•Keep hands clear of drain valve discharge.

It is recommended that the tank be drained and flushed every 6 months to remove sediment which may build up during operation. The water heater should be drained

if being shut down during freezing temperatures. To drain the tank, perform the following steps:

Before removing any access panels or servicing the water heater, make sure the electrical supply to the water heater is turned "OFF".

Failure to do this could result in death, serious bodily injury, or property damage.

1.Place the water heater in Standby Mode by pressing the power button on the user interface module.

2.Turn off the power to the water heater at the circuit breaker/ fuse box.

3.Open a nearby hot water faucet until the water is no longer hot.

4.Close the cold water inlet valve.

5.Connect a hose to the drain valve and terminate it to an adequate drain or external to the building,

6.Open the water heater drain valve and allow all of the water to drain from the tank, Flush the tank with water as needed to remove sediment,

7.Close the drain valve, refill the tank (open the cold water inlet valve), and restart the heater as directed in this manual. IMPORTANT: Do not turn on power to the water heater unless it is completely filled with water. To ensure that the tank is full, open a hot water faucet and allow the water to run until the air is purged and the water flows uninterrupted from the faucet.

8.Press the power button to turn the water heater on. NOTE: The water heater will conduct a system diagnostic prior to operation.

If the water heater is going to be shut down for an extended )eriod, the drain valve should be left open.

Improper installation and use may result in property damage.

•Fill tank with water before operation.

Never use this water heater unless it is completely full of water.

To prevent damage to the tank and heating element, the tank must be filled with water. Water must flow from the hot water

faucet before turning "ON" power.

Element Removal/Replacement

•Before removing any access panels or servicing the water heater, make sure the electrical

supply to the water heater is turned "OFF".

•Failure to do this could result in death, serious bodily injury, or property damage.

Replacement heating elements must be of the same style and voltage/wattage rating as the ones originally in the water heater. This information can be found on the flange or terminal block of the element or on the water heater data plate.

IMPORTANT: Before replacing any element confirm that you have the correct replacement element (wattage). This water heater has a 4500 watt upper element and a 2000 watt lower element. DO NOT replace the element(s) with a wattage different than the ones specified for the upper and/or lower element.

IMPORTANT: Using an element greater than 2000 watts in place of the lower element will damage the water heater.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Ienmore Elite Important Definitions Improper installation and use may result in property damage Fire Hazard / Electric Shock HazardYear Limited Warranty on Water H Eater Safe Installation USE and Service General Installedandmaintained,itshouldgiveyouyearsoftroublefree ThankYouforpurchasingSearswaterheaterProperlyAdditional Tools Needed When Sweat Soldering Materials NeededBasic Tools Removing the Old Water Heater Facts to Consider About the Location Insulation BlanketsWith water Water Piping System Piping Installation SeeClosed SystemCondensate Drain Line Installation Valve and Pipe InsulationProperty Damage Hazard Temperature-Pressure Relief Valve Explosion HazardWiring Filling the Water HeaterWiring Diagram Connecting the Condensate Pump Overflow Shut Off SwitchWater System Piping Post Installation ReviewWater Heater Location Condensate Drain LineAdjusting the User Interface Module Before UsingTemperature Regulation Operational ModesOperating Mode Descriptions Set temperature in Fahrenheit or CelsiusElement Removal/Replacement Draining and FlushingRoutine Preventive Maintenance Air Filter Cleaning/ReplacementDrain Valve Washer Replacement ServiceThermal Expansion Tank Specifications Start Up ConditionsOperational Conditions AIR in HOT Water Faucets Display Shows Indicates Problem Installation Instructions section Kenmore Elite Hybrid Electric Heat Pump Water Heaters Page Managemylife Call anytime, day or night U.S.A. and Canada

153.32116, 153.32118 specifications

The Kenmore 153.32118 and 153.32116 are leading models in the realm of water heaters, designed to enhance efficiency and performance while maintaining user-friendliness. Both models cater to the modern consumer's needs for reliable hot water access in residential settings.

One of the standout features of the Kenmore 153.32118 and 153.32116 is their energy-efficient design. Equipped with advanced insulation technology, these heaters maximize heat retention, which minimizes energy loss and contributes to lower utility bills. The units operate on an efficient heating element that quickly raises water temperature, ensuring that users have hot water available whenever they need it.

Both models come with a user-friendly digital display that allows homeowners to easily adjust settings, monitor water temperature, and receive alerts about system performance. This intuitive interface enhances the overall user experience, making it simple for anyone to operate the heater without requiring extensive technical knowledge.

Safety is a top priority in the design of these water heaters. They are equipped with multiple safety features, such as a temperature control mechanism that prevents overheating and a pressure relief valve that mitigates risks associated with excessive pressure build-up. These safety measures ensure peace of mind for the user, knowing that the appliance is designed to operate safely within a home environment.

The Kenmore 153.32118 and 153.32116 models also boast a compact design, allowing them to fit seamlessly into various spaces, whether in a utility room, basement, or closet. The sleek appearance ensures that they can be incorporated into the home without disrupting the aesthetic flow of the environment.

Maintenance is made simple with these units, as they are designed to require minimal attention over time. The self-cleaning feature helps inhibit sediment buildup, which can affect efficiency and longevity. This technology not only extends the lifespan of the heaters but also ensures consistent performance over time.

In conclusion, the Kenmore 153.32118 and 153.32116 represent a blend of efficiency, safety, and modern technology. With their advanced features and user-friendly design, they meet the demands of today’s households for reliable hot water solutions while keeping energy consumption to a minimum. Whether for daily household needs or specialized tasks, these water heaters stand out as robust options in the market.
Top Page Image Contents