Drain Valve Washer Replacement, Service | Kenmore 153.32118 manual

2.Remove (slide) the filter from the unit.

3.If you are replacing the filter skip to step 4. To clean the filter use a vacuum with a hose attachment to remove any dust or debris.

4.Place the new or cleaned filter into the water heater and secu re the filter to the shroud with the screw loosened earlier. NOTE: Use the guides/slots when inserting the filter into the water heater.

5.Restore power to the water heater and press the power button to turn the water heater on. NOTE: The water heater will conduct a system diagnostic check prior to operation.

Inspection/Cleaning of the Condensate Drain

Pan & Condensate Drain Lines

IMPORTANT: Before attempting to clean or replace the condensate drain pan or lines press the power button to place the water heater in Standby Mode and shut-off power to the water heater at the circuit breaker/fuse box.

1.Remove the access panel (fan side) by loosening the screws securing it to the unit.

2.Check the condensate drain pan and drain lines for any dirt or debris that might interfere with proper drainage. Wipe out any dirt or debris with a damp cloth.

3.Once the condensate drain pan and lines have been inspected/cleaned, secure the access panel to the water heater.

4.Restore power to the water heater and press the power button to turn the water heater on. NOTE: The water heater will conduct a system diagnostic check prior to operation.

Drain Valve Washer Replacement

•Before removing any access panels or servicing the water heater, make sure the electrical

supply to the water heater is turned "OFF".

•Failure to do this could result in death, serious bodily injury, or property damage.

NOTE: For replacement, use a 17/32" x 13/64" x 1/8" thick washer available at your nearest hardware store.

•Before beginning turn "OFF" the electrical power supply to the water heater.

•Follow Draining instructions. See Draining section.

•Turning counter clockwise, remove the hex cap below the screw handle.

•Remove the washer and put the new one in place.

•Screw the handle and cap assembly back into the drain valve and retighten using a wrench. DO NOT OVER TIGHTEN.

•Follow Filling the Water Heater instructions in the Installation Instructions section.

•Check for leaks.

•Turn "ON" electric power to the water heater.

WASHER

FIGURE 21.

Service

Before calling for repair service, read the Start Up Conditions and Operational Conditions found in the Troubleshooting section of this manual.

If a condition persists or you are uncertain about the operation of the water heater, let a qualified person check it out.

Contact Sears Repair Services at 1-800-4-MY-HOME ®

(1-800-469-4663).

153.32116, 153.32118 specifications

The Kenmore 153.32118 and 153.32116 are leading models in the realm of water heaters, designed to enhance efficiency and performance while maintaining user-friendliness. Both models cater to the modern consumer's needs for reliable hot water access in residential settings.

One of the standout features of the Kenmore 153.32118 and 153.32116 is their energy-efficient design. Equipped with advanced insulation technology, these heaters maximize heat retention, which minimizes energy loss and contributes to lower utility bills. The units operate on an efficient heating element that quickly raises water temperature, ensuring that users have hot water available whenever they need it.

Both models come with a user-friendly digital display that allows homeowners to easily adjust settings, monitor water temperature, and receive alerts about system performance. This intuitive interface enhances the overall user experience, making it simple for anyone to operate the heater without requiring extensive technical knowledge.

Safety is a top priority in the design of these water heaters. They are equipped with multiple safety features, such as a temperature control mechanism that prevents overheating and a pressure relief valve that mitigates risks associated with excessive pressure build-up. These safety measures ensure peace of mind for the user, knowing that the appliance is designed to operate safely within a home environment.

The Kenmore 153.32118 and 153.32116 models also boast a compact design, allowing them to fit seamlessly into various spaces, whether in a utility room, basement, or closet. The sleek appearance ensures that they can be incorporated into the home without disrupting the aesthetic flow of the environment.

Maintenance is made simple with these units, as they are designed to require minimal attention over time. The self-cleaning feature helps inhibit sediment buildup, which can affect efficiency and longevity. This technology not only extends the lifespan of the heaters but also ensures consistent performance over time.

In conclusion, the Kenmore 153.32118 and 153.32116 represent a blend of efficiency, safety, and modern technology. With their advanced features and user-friendly design, they meet the demands of today’s households for reliable hot water solutions while keeping energy consumption to a minimum. Whether for daily household needs or specialized tasks, these water heaters stand out as robust options in the market.