Kenmore 153.32116, 153.32118 manual Installation Instructions section

Page 25

®

®

6" Maximum

Air Gap

Read and understand instruction manual and safety messages before installing, operating or servicing this water heater.

Failure to follow instructions and safety messages could result in death or serious injury.

Instruction manual must remain with water heater.

Read this manual first. Then before checking the water heater make sure the electric supply has been turned "OFF", and never turn the electric supply "on" before the tank is completely full of water.

Use this guide to check a "Leaking" water heater. Many suspected "Leakers" are not leaking tanks. Often the source of the water can be found and corrected.

If you are not thoroughly familiar with electric codes, the water heater, and safety practices, contact your local Sears Service Center to check the water heater.

Improper installation and use may result in property damage.

• Fill tank with water before operation.

Never use this water heater unless it is completely full of water. To prevent damage to the tank and heating element, the tank must be filled with water. The water must flow from the hot water faucet before turning "ON" power.

A. *Condensation may be seen on pipes in humid weather or pipe connections may be leaking.

B. Small amounts of water from the temperature-pressure relief valve may be due to thermal expansion or high water pressure in your area.

C. *The temperature-pressure relief valve may be leaking at the tank fitting.

D. *The element may be leaking at the tank fitting.

•Before removing any access panels or servicing the water heater, make sure the electrical

supply to the water heater is turned "OFF".

•Failure to do this could result in death, serious bodily injury, or property damage.

Turn electrical power "OFF", remove access panel and insulation cap with handle. If leaking around element, follow proper draining instructions and remove element. Reposition or replace gasket on element. Place element into opening and tighten securely. Then follow Filling the Water Heater instructions in the Installation Instructions section.

E. Water from drain valve may be due to the valve being opened slightly

F. *The drain valve may be leaking at the tank fitting.

G. Water in the water heater bottom or on the floor may be from condensation, loose connections or the temperature- pressure relief valve. DO NOT replace the water heater until a full inspection of all possible water sources is made and necessary corrective steps taken.

Check for leaks at the condensate lines and connection points. If a condensate pump is used check for leaks at the pump. Also check to see if the pump is not operating or clogged.

Leakage from other appliances, water lines, or ground seepage should also be checked.

To check where threaded portion enters tank, insert cotton swab between jacket opening and fitting. If cotton is wet, follow Draining instructions in the Service and Adjustment section and then remove fitting. Put pipe dope or teflon tape on the threads and replace. Then follow Filling the Water Heater instructions in the

Installation Instructions section.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Ienmore Elite Important Definitions Fire Hazard / Electric Shock Hazard Improper installation and use may result in property damageYear Limited Warranty on Water H Eater Safe Installation USE and Service General ThankYouforpurchasingSearswaterheaterProperly Installedandmaintained,itshouldgiveyouyearsoftroublefreeMaterials Needed Additional Tools Needed When Sweat SolderingBasic Tools Removing the Old Water Heater Insulation Blankets Facts to Consider About the LocationWith water SeeClosed System Water Piping System Piping InstallationValve and Pipe Insulation Condensate Drain Line InstallationProperty Damage Hazard Explosion Hazard Temperature-Pressure Relief ValveFilling the Water Heater WiringConnecting the Condensate Pump Overflow Shut Off Switch Wiring DiagramWater Heater Location Post Installation ReviewWater System Piping Condensate Drain LineTemperature Regulation Before UsingAdjusting the User Interface Module Operational ModesSet temperature in Fahrenheit or Celsius Operating Mode DescriptionsDraining and Flushing Element Removal/ReplacementAir Filter Cleaning/Replacement Routine Preventive MaintenanceService Drain Valve Washer ReplacementStart Up Conditions Thermal Expansion Tank SpecificationsOperational Conditions AIR in HOT Water Faucets Display Shows Indicates Problem Installation Instructions section Kenmore Elite Hybrid Electric Heat Pump Water Heaters Page Call anytime, day or night U.S.A. and Canada Managemylife

153.32116, 153.32118 specifications

The Kenmore 153.32118 and 153.32116 are leading models in the realm of water heaters, designed to enhance efficiency and performance while maintaining user-friendliness. Both models cater to the modern consumer's needs for reliable hot water access in residential settings.

One of the standout features of the Kenmore 153.32118 and 153.32116 is their energy-efficient design. Equipped with advanced insulation technology, these heaters maximize heat retention, which minimizes energy loss and contributes to lower utility bills. The units operate on an efficient heating element that quickly raises water temperature, ensuring that users have hot water available whenever they need it.

Both models come with a user-friendly digital display that allows homeowners to easily adjust settings, monitor water temperature, and receive alerts about system performance. This intuitive interface enhances the overall user experience, making it simple for anyone to operate the heater without requiring extensive technical knowledge.

Safety is a top priority in the design of these water heaters. They are equipped with multiple safety features, such as a temperature control mechanism that prevents overheating and a pressure relief valve that mitigates risks associated with excessive pressure build-up. These safety measures ensure peace of mind for the user, knowing that the appliance is designed to operate safely within a home environment.

The Kenmore 153.32118 and 153.32116 models also boast a compact design, allowing them to fit seamlessly into various spaces, whether in a utility room, basement, or closet. The sleek appearance ensures that they can be incorporated into the home without disrupting the aesthetic flow of the environment.

Maintenance is made simple with these units, as they are designed to require minimal attention over time. The self-cleaning feature helps inhibit sediment buildup, which can affect efficiency and longevity. This technology not only extends the lifespan of the heaters but also ensures consistent performance over time.

In conclusion, the Kenmore 153.32118 and 153.32116 represent a blend of efficiency, safety, and modern technology. With their advanced features and user-friendly design, they meet the demands of today’s households for reliable hot water solutions while keeping energy consumption to a minimum. Whether for daily household needs or specialized tasks, these water heaters stand out as robust options in the market.
Top Page Image Contents