Cisco Systems 2900, OL-24281-01 manual Txb-N

Page 13

Chapter 1 Installation

Mounting

1	RJ-45 Connector	7	Standoff

2	Ethernet Cable	8	UTP Connector

3	Video Coaxial Cable	9	Back Box Circuit Board

4	16-Pin Connector	10	Audio Connectors

5	Heat Sink Standoff	11	TXB-N

6	Captive Screw

Step 3 Connect the auxiliary, alarm, and other wiring to the back box circuit board (see Figure 1-6).

Note Aux 1: Maximum 2 A at low voltage (<40 V).

Aux 2: Maximum 30 mA at 32 VDC.

If you are installing an environmental back box in a railway application, attach a ground wire from the circuit board power connector to a structural ground using at least 18-gauge wire.

Figure 1-6 Connect the Wiring to the Circuit Board

ALARMS

AUX1

1 2 3 4 5 6

7

GND

NO

COM

NC AUX2

GND

VIDEO

PWR- GND PWR+ RX- RX+ TX- TX+ UTP+ UTP-

Step 4 If you plan to use the audio functions, install your audio cables into the audio line-in and line-out connectors on the TXB-N.

Cisco Video Surveillance IP PTZ Dome Camera User Guide, Cisco 2900 Series IP Dome

	OL-24281-01	1-5

Image 13

Contents Americas Headquarters Cisco Video Surveillance IP PTZ Dome Camera User GuidePage N T E N T S Customizing the Appearance of the Text Overlay Creating a New User OL-24281-01 Organization OverviewViii Mounting InstallationDoor open In-CeilingAttaching the Pendant Back Box to the Mount PendantRemoving the TXB-N WiringTXB-N Connecting Audio to the TXB-N Routing the Cables in the Back Box Wire Gauge Total VA Installing the Dome DriveCable Type Maximum DistanceIn-Ceiling, Pendant, Installing the Lower DomeAttach the back box leash to the lower dome see Figure Serial Port Settings Switch SettingsSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 Switch SettingSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 Switch Setting Address SW1-1 SW1-2 SW1-3 SW1-4 SW1-5OL-24281-01 OFF 100 116 151 186 221 System Requirements OperationLive Video Accessing the IP DeviceLive Video Page Icons Icon Description PTZ ControlsControl Description Selecting a StreamQuickView Stream Primary Stream and Secondary StreamUnicast Displaying Video in the Multiscreen View Taking a SnapshotMulticast Accessing the Device Menus SettingsGeneral Settings System TabInformation Settings Configuring the Time SettingsChanging the Device Name Restoring All Camera Defaults Rebooting the CameraCustomizing the Appearance of the Text Overlay Generating a System LogSSL Settings General Network SettingsSSH Settings Network TabTurning On Dhcp Changing the HostnameTurning Off Dhcp Generating a Certificate Request Selecting the Secure Sockets Layer ModeGenerating a Self-Signed Certificate Enabling Secure Shell Selecting Snmp SettingsSnmp V2c Settings Configuring Snmp V2cConfiguring Snmp Camera Configuration TabGeneral Presets/Patterns Adjusting the Video PropertiesUsing On-Screen Display OSD to Access Camera Menus Configuring Home Preset Configuring a PresetPreset/Pattern Selecting a Configured PresetLive View Selecting a Configured Pattern Configuring a PatternVideo Configuration Video PresetsAudio Configuration Streams TabSelect Video Preset Configuration Selecting a Video Preset ConfigurationCustom Video Stream Configuration Configuring a Custom Video StreamImage Rate and Bit Rate Compression StandardsBit Rate kbps Resolution ResolutionSecondary Stream H.264 Secondary Stream Mjpeg Frame Rate1500 FPS @ 3 Mbps 1024 2000 768 256 128 768 512 256 128 Frame Rate Mjpeg Encoding ResolutionFPS @ 512 kbps 128 256 CIF CID 768 FPS @ 1024 kbps 256 128 2500 FPS @ 5.4 Mbps 1024 12.5 1500 256 768 128 Quality of Service for Differentiated Services Code Point Selecting the Audio Configuration SettingsFrame Interval Advanced Sharpening10 Audio Configuration Users Users Tab11 General Settings Page for Users Selecting the Users and Groups SettingsCreating a New User Editing a User Events TabDeleting a User Creating a System Event Source Creating a Timer Event SourceSources HandlersDeleting an Event Source Editing an Event SourceCreating an Event Handler Send Email Creating an Event Handler Upload Jpeg to FTP Server Editing an Event Handler Example Handler Filter SetupDeleting an Event Handler Operation Events Tab Chapter Issue Possible Cause Suggested Resolution TroubleshootingAppendix a Troubleshooting Specification SpecificationsElectrical Mechanical dome drive only Environmental D E IN-2 IN-3 IN-4

Related manuals

Manual 6 pages 15.75 Kb