Motorola MICOM-2ES/2RS/2TS ALE manual Abcpack, To display LQA for the received call, Link State

Page 33

New ALE Features

If the received call includes a message, an exclamation

MOTOROLA

 

FROM

 

mark precedes the station name, and the name is

!ABC:PACK

followed by a colon and the message.

CALL

LQA

 

 

If the calling station name and message are too long and

MOTOROLA

 

do not fit in the display, press <->(F3) to enter the View

FROM

 

!ABC:PACK

mode, where you can scroll right and left to display the

CALL

LQA <-->

whole message.

To display LQA for the received call:

Press LQA (F2). You will see the channel in use, and its LQA score.

Link State

After the radio successfully receives or transmits a call, it is in the link state.

If the call was received from another radio, the display

MOTOROLA

includes the word FROM in the first line, as well as the

FROM

ABC

name of the station which initiated the call (if a message has

CALL LQA

been received, it is also displayed).

 

MON

MONs

MON

If the call was initiated by your radio, the display includes the word LINK in the first line, as well as the destination address.

Link State Options

MOTOROLA

LINK 1234

CALL PAGE

MONs

While in the link state, you can operate the functions described below using the function keys.

To scroll to the desired screen, press MORE.

The change of link options is temporary. When you exit the link state for the current call, all the changed parameters will be lost.

Note

<->(F1) activates the View mode, where you can view the entire station address (when over 11 characters), as well as received messages, if any (when over 11 characters).

PAGE (F2) enables you to select a message to be sent to the station you are linked to. After a message is selected, you can edit it.

The PAGE function is not available when receiving an AllCall.

Note

_________________________________________________________________________________________________ 19

Image 33
Contents MICOM-2ES/2RS/2TS ALE Page Commercial Warranty Standard Computer Software Copyrights MICOM-2ES/2RS/2TS ALE HF-SSB Transceiver Page General Safety Precautions This radio is intended for use in occupational/controlled Radio device is not authorized for general populationConsumer or similar use Federal Communication Commission Regulations Communication Commission Regulations section Interference EMI if inadequately shielded, designed, or Driver SafetyOperational Warnings Table of Contents Viii Introduction Channel CH Menu Frequency Freq Menu Prog Menu Radio Parameters Programming Prog Menu ALE Parameters Programming ALE Addressing Method Selective CallingUse of @ Stuffing Symbol Address and Call TypesIndividual Station Address Net Addresses Group AddressesSpecial Addressing Modes Use of Wildcards ? ? ? Use of ? Wildcard SymbolAllCall Addresses Use of ? Wildcard SymbolSelf Addresses AnyCallsNull Address Inlink AddressUsing the MultiNet Feature Using the Caller Stack Using ALE Functions in the Channel ModeMessages Quick CallEnabling the ALE Mode Entering the ALE ModeTo enter the ALE mode ALE and Rx Only or Tx Only ChannelsALE NET ALE Mode OptionsInformation appearing in this section updates the ALE Receiving and Transmitting Calls in ALE ModeOperating instructions presented in previous publications ALE operating instructions appearing in this SupplementReceiving an individual call Receiving Calls in ALE ModeReceiving a net call Receiving an AllCallReceiving a sounding call Receiving an AnyCallReceiving a bidirectional handshake call To answer an incoming callAbcpack Function is not available when receiving an AllCallTo display LQA for the received call Link StateRPL MORE, F1 To replace the channel Replacing the Current Channel While in the Link StateTo view the calls in the stack Using the Caller StackTo return a call to a station registered in the stack AddressTo remove an address from the stack Disconnecting CallsTo disconnect an incoming call END CallingUsing the MON F4 key Transmitting Calls in ALE ModeSelecting the Desired Net To select a netTo transmit an individual call with MultiNet OFF Calls to an Individual StationTo transmit an individual call with MultiNet on Your radio switches to the Channel mode for the duration Channel mode. If the other station is in the Channel modeTo transmit on a specific channel Pressing Best F3 is the first scanned channel of the netContained a message Quick CallData exists To send a quick callTo use Autodial to send a call Using AutodialSending Messages To transmit an individual call with a messageAMD11 AMD Mess To send a message during a call link state To select a special call type Other Types of CallsOption Capabilities See Page … ALLANY GRPWild SelfTo send global AllCall using the Call function To send global AllCall using the ESC keyGL Allcall Link GL AllcallTo send selective AllCall If you decide to send a Global AllCall, press Glob F3If you decide to send a global AllCall, press Glob F3 or ? Link SL Allcall Transmitting Net Calls To transmit a net callCall NET Characters. Therefore, when an address is not an exact Transmitting Group CallsExplained on page 6, each ALE word must include Request is rejected and you will see for a few seconds AT To transmit a group callIf adding the station would cause To define or change a groupTotal length of the station addresses After pressing ADD F1 you will seeDIR BU Transmitting AnyCallsDIR BUD To transmit an AnyCall Call ANYALL Ending ALL ENDING59 ALL ENDING1You can press Stop F1 or ESC to abort the entire process Link ANYTo transmit a wildcard call Transmitting Wildcard CallsAT Least Call WildTransmitting a Self Call You can also include the self address in a group callTo send a self-call Bidirectional Handshake MICOM-2 can also be programmed to automatically initiateOptions Bdir LQATo execute a bidirectional handshake with a net Bdir NETChange the net, see Sounding To manually initiate soundingSond Sound OFF Do not enable the inlink function when communicating with a Using the Inlink FunctionAll the stations Radio that does not support the full ALE capabilitiesTransmitting ALE Calls in the Channel Mode Menu To enter the ALE Programming modeProg NET RCVDIR AMD Programming NetsYou can also edit, or prepare a new message, on-line OPT Auto StorName Memb Chan GET Eras Default ValuesSetting the Net Options Directory Parameters AMD Message ConfigurationExal Alrt ALE Options ConfigurationMlqa Qcal If the directory is full, new addresses will not be addedMNT Ilnk BdlkStoring ALE Parameters Auto Dial ParametersAMD Ilnk BdlkUsing the New Station Address Filter

MICOM-2ES/2RS/2TS ALE specifications

Motorola MICOM-2ES/2RS/2TS ALE is a sophisticated communication system designed for critical and emergency communication applications. The system is part of Motorola’s esteemed MICOM range, known for its ruggedness and reliability in challenging environments. ALE, or Automatic Link Establishment, is a crucial feature of the MICOM series, enabling efficient and automated establishment of radio links between devices, which is essential for operations where timely communication is a matter of urgency.

One of the main features of the MICOM-2 series is its robust ALE capabilities, allowing operators to automatically find the best frequency for communication based on current conditions. This dynamic frequency selection not only enhances the reliability of the communication link but also minimizes the possibility of interference from other signals, which can be critical in emergency situations.

The MICOM-2ES, 2RS, and 2TS models feature advanced digital signal processing technologies that optimize audio clarity and reception. This ensures that communication remains clear even in noisy environments, which is a pivotal factor in emergency response scenarios. With a digital signal processor onboard, the system is capable of filtering out unwanted noise and enhancing the quality of the transmitted audio.

These models support multiple modes of operation, including both simplex and duplex communications. Such versatility allows users to adapt the system to various communication needs, augmenting its effectiveness in a range of operation scenarios. Furthermore, the MICOM-2 series is compatible with various antenna configurations, enhancing the operational range and flexibility of the system.

User-friendliness is another hallmark of the MICOM-2ES/2RS/2TS ALE systems, as they feature an intuitive user interface that simplifies operation, allowing for quick and efficient communication in high-pressure situations. Emergency responders and military personnel benefit greatly from such ease of use, leading to faster response times and improved overall coordination.

Additionally, the robustness of the Motorola MICOM-2 series ensures that it can withstand extreme environmental conditions. The units are designed to operate in harsh weather and rugged terrains, making them ideal for outdoor usage in emergency or military applications. All these features combined make the Motorola MICOM-2ES/2RS/2TS ALE a reliable choice for organizations that require high-performance communication solutions in demanding conditions.