Motorola MICOM-2ES/2RS/2TS ALE manual Transmitting AnyCalls, Dir Bud

Page 55

New ALE Features

As you scroll through the directory, you will see DIR for stations that can be added, and ADDED for those already added. If the station you want to add to the group is not in the directory:

MOTOROLA

DIR BU_

!" Enter the new station using the keypad. If you make a mistake, scroll to the desired position using <--(F2) and/or -->(F3), or clear (CLR (F4)) the whole entry and start again.

!" When ready, press SAVE (F1) to store the new station in the directory.

Now you can add it to the group by pressing ADD (F1).

Transmitting AnyCalls

SAVE <-- --> CLR

MOTOROLA

DIR

BUD

ADD <-- --> OK

An AnyCall is a general broadcast which your radio uses to simultaneously establish links with other stations. An AnyCall can also include a message.

If so required, you can set your radio so that it cannot send

AnyCalls.

Note

AnyCall is somewhat similar to AllCall, except that it requests responses from the other stations and therefore it can be used to detect new stations. Another difference is that you can also select the channel on which the AnyCall will be transmitted (alternatively, you can let the radio select automatically the channel).

When radios in other nets have their MultiNet feature enabled,

AnyCalls may also reach these radios. See details on page 11.

Note

You can send three types of AnyCalls (see also description of addressing modes on pages 6 to 11):

General: the address sent by your radio is @@?. This is a simultaneous call addressed to all the stations.

Selective: you specify the last character of the address. This is a simultaneous call addressed only to the stations whose names (addresses) end with a character you specify.

_________________________________________________________________________________________________ 41

Image 55
Contents MICOM-2ES/2RS/2TS ALE Page Commercial Warranty Standard Computer Software Copyrights MICOM-2ES/2RS/2TS ALE HF-SSB Transceiver Page General Safety Precautions Radio device is not authorized for general population This radio is intended for use in occupational/controlledConsumer or similar use Federal Communication Commission Regulations Communication Commission Regulations section Interference EMI if inadequately shielded, designed, or Driver SafetyOperational Warnings Table of Contents Viii Introduction Channel CH Menu Frequency Freq Menu Prog Menu Radio Parameters Programming Prog Menu ALE Parameters Programming ALE Addressing Method Selective CallingAddress and Call Types Use of @ Stuffing SymbolIndividual Station Address Group Addresses Net AddressesSpecial Addressing Modes Use of Wildcards ? ? ? Use of ? Wildcard SymbolAllCall Addresses Use of ? Wildcard SymbolInlink Address AnyCallsSelf Addresses Null AddressUsing the MultiNet Feature Quick Call Using ALE Functions in the Channel ModeUsing the Caller Stack MessagesALE and Rx Only or Tx Only Channels Entering the ALE ModeEnabling the ALE Mode To enter the ALE modeALE NET ALE Mode OptionsALE operating instructions appearing in this Supplement Receiving and Transmitting Calls in ALE ModeInformation appearing in this section updates the ALE Operating instructions presented in previous publicationsReceiving an AllCall Receiving Calls in ALE ModeReceiving an individual call Receiving a net callTo answer an incoming call Receiving an AnyCallReceiving a sounding call Receiving a bidirectional handshake callLink State Function is not available when receiving an AllCallAbcpack To display LQA for the received callRPL MORE, F1 To replace the channel Replacing the Current Channel While in the Link StateAddress Using the Caller StackTo view the calls in the stack To return a call to a station registered in the stackEND Calling Disconnecting CallsTo remove an address from the stack To disconnect an incoming callTo select a net Transmitting Calls in ALE ModeUsing the MON F4 key Selecting the Desired NetTo transmit an individual call with MultiNet OFF Calls to an Individual StationTo transmit an individual call with MultiNet on Pressing Best F3 is the first scanned channel of the net Channel mode. If the other station is in the Channel modeYour radio switches to the Channel mode for the duration To transmit on a specific channelTo send a quick call Quick CallContained a message Data existsTo use Autodial to send a call Using AutodialTo transmit an individual call with a message Sending MessagesAMD11 AMD Mess To send a message during a call link state ALL Other Types of CallsTo select a special call type Option Capabilities See Page …Self GRPANY WildLink GL Allcall To send global AllCall using the ESC keyTo send global AllCall using the Call function GL AllcallIf you decide to send a Global AllCall, press Glob F3 To send selective AllCallIf you decide to send a global AllCall, press Glob F3 or ? Link SL Allcall To transmit a net call Transmitting Net CallsCall NET Transmitting Group Calls Characters. Therefore, when an address is not an exactExplained on page 6, each ALE word must include Request is rejected and you will see for a few seconds AT To transmit a group callAfter pressing ADD F1 you will see To define or change a groupIf adding the station would cause Total length of the station addressesTransmitting AnyCalls DIR BUDIR BUD Call ANY To transmit an AnyCallALL Ending Link ANY ALL ENDING1ALL ENDING59 You can press Stop F1 or ESC to abort the entire processTo transmit a wildcard call Transmitting Wildcard CallsAT Least Call WildYou can also include the self address in a group call Transmitting a Self CallTo send a self-call MICOM-2 can also be programmed to automatically initiate Bidirectional HandshakeOptions Bdir LQABdir NET To execute a bidirectional handshake with a netChange the net, see To manually initiate sounding SoundingSond Sound OFF Radio that does not support the full ALE capabilities Using the Inlink FunctionDo not enable the inlink function when communicating with a All the stationsTransmitting ALE Calls in the Channel Mode NET RCV To enter the ALE Programming modeMenu ProgOPT Auto Stor Programming NetsDIR AMD You can also edit, or prepare a new message, on-lineName Memb Chan GET Eras Default ValuesSetting the Net Options Directory Parameters AMD Message ConfigurationIf the directory is full, new addresses will not be added ALE Options ConfigurationExal Alrt Mlqa QcalMNT Ilnk BdlkIlnk Bdlk Auto Dial ParametersStoring ALE Parameters AMDUsing the New Station Address Filter

MICOM-2ES/2RS/2TS ALE specifications

Motorola MICOM-2ES/2RS/2TS ALE is a sophisticated communication system designed for critical and emergency communication applications. The system is part of Motorola’s esteemed MICOM range, known for its ruggedness and reliability in challenging environments. ALE, or Automatic Link Establishment, is a crucial feature of the MICOM series, enabling efficient and automated establishment of radio links between devices, which is essential for operations where timely communication is a matter of urgency.

One of the main features of the MICOM-2 series is its robust ALE capabilities, allowing operators to automatically find the best frequency for communication based on current conditions. This dynamic frequency selection not only enhances the reliability of the communication link but also minimizes the possibility of interference from other signals, which can be critical in emergency situations.

The MICOM-2ES, 2RS, and 2TS models feature advanced digital signal processing technologies that optimize audio clarity and reception. This ensures that communication remains clear even in noisy environments, which is a pivotal factor in emergency response scenarios. With a digital signal processor onboard, the system is capable of filtering out unwanted noise and enhancing the quality of the transmitted audio.

These models support multiple modes of operation, including both simplex and duplex communications. Such versatility allows users to adapt the system to various communication needs, augmenting its effectiveness in a range of operation scenarios. Furthermore, the MICOM-2 series is compatible with various antenna configurations, enhancing the operational range and flexibility of the system.

User-friendliness is another hallmark of the MICOM-2ES/2RS/2TS ALE systems, as they feature an intuitive user interface that simplifies operation, allowing for quick and efficient communication in high-pressure situations. Emergency responders and military personnel benefit greatly from such ease of use, leading to faster response times and improved overall coordination.

Additionally, the robustness of the Motorola MICOM-2 series ensures that it can withstand extreme environmental conditions. The units are designed to operate in harsh weather and rugged terrains, making them ideal for outdoor usage in emergency or military applications. All these features combined make the Motorola MICOM-2ES/2RS/2TS ALE a reliable choice for organizations that require high-performance communication solutions in demanding conditions.