Motorola MICOM-2ES/2RS/2TS ALE Transmitting Calls in ALE Mode, Using the MON F4 key, Ale Net

Page 38

MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide

Transmitting Calls in ALE Mode

To transmit an ALE call, you must specify the destination. In general, the destination consists of a net and one or more stations (members of the specified net):

•When the MultiNet function (page 12) is disabled, the destination net is always the currently selected net (its number is displayed on the LCD while the radio is scanning). Therefore, if you do not want to select a different net, you can skip directly to the selection of the destination station(s).

•When the MultiNet function is enabled, first you must always select a net and then the destination station(s).

To expedite the transmission of an AllCall, you can send a global AllCall by pressing the P/ESC key for a few seconds.

MICOM-2 stores the last called address, so you can simply press the PTT twice in rapid sequence (double pressing) to call again that address. This also applies to AllCall, and therefore after sending AllCall for the first time, you can send it again by double pressing the PTT.

 

 

 

 

 

If you want to monitor the call set up process on the speaker and

 

 

 

 

 

be alerted by a beep when the link is set up, turn the monitor on,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

using the MON (F4) key.

Note

 

Selecting the Desired Net

➤To select a net:

1.Press MENU and select ALE (F3).

The radio displays current active net number, flashing.

2.To change the currently used net, press the

UP/DOWN keys, or enter the net number on the keypad, and then press ENTER.

MOTOROLA

ALE

NET# 7

MOTOROLA

ALE

NET

1

1

CALL

LQA

MON

24_________________________________________________________________________________________________

Page 37 Page 39
Image 38
Page 37 Page 39
Contents MICOM-2ES/2RS/2TS ALE Page Commercial Warranty Standard Computer Software Copyrights MICOM-2ES/2RS/2TS ALE HF-SSB Transceiver Page General Safety Precautions Consumer or similar use This radio is intended for use in occupational/controlledRadio device is not authorized for general population Federal Communication Commission Regulations Communication Commission Regulations section Driver Safety Interference EMI if inadequately shielded, designed, orOperational Warnings Table of Contents Viii Introduction Channel CH Menu Frequency Freq Menu Prog Menu Radio Parameters Programming Prog Menu ALE Parameters Programming Selective Calling ALE Addressing MethodIndividual Station Address Use of @ Stuffing SymbolAddress and Call Types Special Addressing Modes Use of Wildcards Net AddressesGroup Addresses Use of ? Wildcard Symbol ? ? ?Use of ? Wildcard Symbol AllCall AddressesNull Address AnyCallsSelf Addresses Inlink AddressUsing the MultiNet Feature Messages Using ALE Functions in the Channel ModeUsing the Caller Stack Quick CallTo enter the ALE mode Entering the ALE ModeEnabling the ALE Mode ALE and Rx Only or Tx Only ChannelsALE Mode Options ALE NETOperating instructions presented in previous publications Receiving and Transmitting Calls in ALE ModeInformation appearing in this section updates the ALE ALE operating instructions appearing in this SupplementReceiving a net call Receiving Calls in ALE ModeReceiving an individual call Receiving an AllCallReceiving a bidirectional handshake call Receiving an AnyCallReceiving a sounding call To answer an incoming callTo display LQA for the received call Function is not available when receiving an AllCallAbcpack Link StateRPL MORE, F1 Replacing the Current Channel While in the Link State To replace the channelTo return a call to a station registered in the stack Using the Caller StackTo view the calls in the stack AddressTo disconnect an incoming call Disconnecting CallsTo remove an address from the stack END CallingSelecting the Desired Net Transmitting Calls in ALE ModeUsing the MON F4 key To select a netCalls to an Individual Station To transmit an individual call with MultiNet OFFTo transmit an individual call with MultiNet on To transmit on a specific channel Channel mode. If the other station is in the Channel modeYour radio switches to the Channel mode for the duration Pressing Best F3 is the first scanned channel of the netData exists Quick CallContained a message To send a quick callUsing Autodial To use Autodial to send a callAMD11 AMD Mess Sending MessagesTo transmit an individual call with a message To send a message during a call link state Option Capabilities See Page … Other Types of CallsTo select a special call type ALLWild GRPANY SelfGL Allcall To send global AllCall using the ESC keyTo send global AllCall using the Call function Link GL AllcallIf you decide to send a global AllCall, press Glob F3 or ? To send selective AllCallIf you decide to send a Global AllCall, press Glob F3 Link SL Allcall Call NET Transmitting Net CallsTo transmit a net call Explained on page 6, each ALE word must include Characters. Therefore, when an address is not an exactTransmitting Group Calls To transmit a group call Request is rejected and you will see for a few seconds ATTotal length of the station addresses To define or change a groupIf adding the station would cause After pressing ADD F1 you will seeDIR BUD DIR BUTransmitting AnyCalls ALL Ending To transmit an AnyCallCall ANY You can press Stop F1 or ESC to abort the entire process ALL ENDING1ALL ENDING59 Link ANYTransmitting Wildcard Calls To transmit a wildcard callCall Wild AT LeastTo send a self-call Transmitting a Self CallYou can also include the self address in a group call Options Bidirectional HandshakeMICOM-2 can also be programmed to automatically initiate LQA BdirChange the net, see To execute a bidirectional handshake with a netBdir NET Sond Sound OFF SoundingTo manually initiate sounding All the stations Using the Inlink FunctionDo not enable the inlink function when communicating with a Radio that does not support the full ALE capabilitiesTransmitting ALE Calls in the Channel Mode Prog To enter the ALE Programming modeMenu NET RCVYou can also edit, or prepare a new message, on-line Programming NetsDIR AMD OPT Auto StorName Memb Chan Default Values GET ErasSetting the Net Options AMD Message Configuration Directory ParametersMlqa Qcal ALE Options ConfigurationExal Alrt If the directory is full, new addresses will not be addedIlnk Bdlk MNTAMD Auto Dial ParametersStoring ALE Parameters Ilnk BdlkUsing the New Station Address Filter

MICOM-2ES/2RS/2TS ALE specifications

Motorola MICOM-2ES/2RS/2TS ALE is a sophisticated communication system designed for critical and emergency communication applications. The system is part of Motorola’s esteemed MICOM range, known for its ruggedness and reliability in challenging environments. ALE, or Automatic Link Establishment, is a crucial feature of the MICOM series, enabling efficient and automated establishment of radio links between devices, which is essential for operations where timely communication is a matter of urgency.

One of the main features of the MICOM-2 series is its robust ALE capabilities, allowing operators to automatically find the best frequency for communication based on current conditions. This dynamic frequency selection not only enhances the reliability of the communication link but also minimizes the possibility of interference from other signals, which can be critical in emergency situations.

The MICOM-2ES, 2RS, and 2TS models feature advanced digital signal processing technologies that optimize audio clarity and reception. This ensures that communication remains clear even in noisy environments, which is a pivotal factor in emergency response scenarios. With a digital signal processor onboard, the system is capable of filtering out unwanted noise and enhancing the quality of the transmitted audio.

These models support multiple modes of operation, including both simplex and duplex communications. Such versatility allows users to adapt the system to various communication needs, augmenting its effectiveness in a range of operation scenarios. Furthermore, the MICOM-2 series is compatible with various antenna configurations, enhancing the operational range and flexibility of the system.

User-friendliness is another hallmark of the MICOM-2ES/2RS/2TS ALE systems, as they feature an intuitive user interface that simplifies operation, allowing for quick and efficient communication in high-pressure situations. Emergency responders and military personnel benefit greatly from such ease of use, leading to faster response times and improved overall coordination.

Additionally, the robustness of the Motorola MICOM-2 series ensures that it can withstand extreme environmental conditions. The units are designed to operate in harsh weather and rugged terrains, making them ideal for outdoor usage in emergency or military applications. All these features combined make the Motorola MICOM-2ES/2RS/2TS ALE a reliable choice for organizations that require high-performance communication solutions in demanding conditions.
Top Page Image Contents