New Buck Corporation 1110 manual

Page 7

21.All heater screens must be kept clean when operating the gas logs.

22.”WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.”

23.Do not use this heater for burning trash or cooking. Never place matches, paper, garbage, or any other material on top of logs or into the flames.

24.Do not install or operate this heater in areas where impurities in the air exist (such as tobacco smoke or heavy cooking grease). Particles from impurities may discolor walls.

25.Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.

26.Children and adults should be alerted to the hazards of high surface temperature and should stay away to avoid burns or clothing ignition.

27.Young children should be carefully supervised when they are in the same room with the appliance.

28.An unvented room heater having an input rating of more than 10,000 Btu per hour shall not be installed in a bathroom or bedroom.

29.The appliance and its appliance main gas valve must be disconnected from the gas supply pipping system during any pressure testing of that system at test pressure in excess of 1/2 psi (3.5 kPa).

30.The appliance must be isolated from the gas supply pipping system by closing its equipment shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psi (3.5 kPa).

31.WARNING: Do not allow fans to blow directly into fireplace. Avoid any drafts that alter burner flame patterns.”

32.WARNING: Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this heater.”

5

Image 7
Contents 8000 Highway 226 South Spruce Pine, NC NEW BUCK CORPORATIONMODEL 1110 VENT-FREEGAS HEATER Manufacturer NEW BUCK CORPORATION P.O. BoxPage TABLE OF CONTENTS Page SAFETY INFORMATION WARNINGS Do not try to light any appliance 22.”WARNING Failure to keep the primary air openings of the burners clean may result in sooting and property damage.” PRODUCT IDENTIFICATION PIEZO IGNITION SYSTEM PRODUCT FEATURESUNPACKING SAFETY DEVICEMINIMUM CLEARANCES TO COMBUSTIBLE CONSTRUCTION 3.Freestanding with optional wooden mantel INSTALLATION1.Wall Mounted 2.Freestanding heater with optional pedestalCLEANING INFORMATION FREESTANDING OPTIONAL WOODEN MANTEL INSTALLATION FREESTANDING WITH OPTIONAL PEDESTAL INSTALLATIONOPTIONAL “L” BRACKETS 2 AND SCREWS 2 PRO DETERMINING FRESH-AIRFLOW FOR HEATER LOCATION PRODUCING ADEQUATE VENTILATIONVent-freeheater VENTILATION AIR FROM INSIDE BUILDING VENTILATION AIRVENTILATION AIR FROM OUTDOORS FLAME GAS CONNECTIONPropane Supply Tank CONNECTING TO A GAS SUPPLYExternal Regulator Vent Pointing Down Installation must include manual shutoff valve and plugged 1/2 NPT tap. Locate NPT tap within reach for test gauge hook-up.NPT tap must be upstream from unit GAS PRESSURE CHECK Logs are shipped secured in unit LOG PLACEMENT FORFront View of Logs LIGHTING INSTRUCTIONS MODULATING VALVEMAXITROL FOR YOUR SAFETY, READ BEFORE LIGHTINGOPERATING INSTRUCTIONS for “HIGH” LIGHTING INSTRUCTIONSto IGNITE and for “LOW”IGNITER ELECTRODE THERMO-COUPLE TO TURN OFF GAS TO APPLIANCEO.D.S PILOT BURNER THERMOSTAT CONTROL OPERATION MANUAL LIGHTING PROCEDUREPROPANE FLAME CHECKFLAME NATURALINCORRECT FLAME PATTERN AT HIGH POSITION BURNER FLAME PATTERNCORRECT FLAME PATTERN AT HIGH POSITION Figure 1815 - Correct Burner Flame PatternJUMPERTHERMOSTAT WIRING DIAGRAMPOWER CORD MOTORSERVICING REPAIR PARTSCLEANING IMPORTANT SAFEGUARDSTROUBLE-SHOOTING POSSIBLE PROBLEMSOLUTION OBSERVED1.Control knob is not fully pressed in Delayed ignition of burner 1. Heater produces a clinking MODEL TECHNICAL SERVICEMODULATING VALVE PARTS LIST MOTOR, AND ALL REMOVABLE PARTS BLOWN UP VIEW OF HEATER, FANMaxitrol Valve PARTS LISTBLOWN UP VIEW OF BURNER ASSEMBLY NEW BUCK CORPORATION LIMITED WARRANTY ON VENT-FREEGAS LOG HEATER