Heat & Glo LifeStyle VRT-BZ-P-AUB About on Mode, About OFF Mode, Turning on the Fireplace

Page 62

About ON Mode

•All functions can be accessed when the remote control is in the ON mode.

•Only active functions will be displayed when the remote control is in the ON mode. For example: if the fan is the only function that’s active, the fan icon and flame will be the only icon shown in the display.

About OFF Mode

Only the following functions can be accessed in the OFF mode:

•AUX1

•AUX2

Only active functions will be displayed when the remote control is in the OFF mode.

Turning ON the Fireplace

•Press and hold the POWER button for 5 seconds to unlock remote, back light will illuminate. Press the POWER button again to turn the fireplace ON. The fireplace will first ignite the pilot. The main burner will be lit, once the pilot flame has been established. The remote will be locked again when the fireplace is turned OFF.

NOTICE: Whenever the fireplace is cycled from OFF to ON, the main burner will light on high for 10 seconds before returning to the previous user setting.

Adjusting Flame Height

•Press the MENU button to activate the menu.

•Using the UP and DOWN arrows highlight the FLAME icon and press SELECT.

•Use the UP and DOWN arrows to adjust the FLAME HEIGHT, then press SELECT. The FLAME HEIGHT can be adjusted to 5 different settings.

NOTICE: FLAME HEIGHT will not be adjustable for first ten seconds when fireplace is turned on.

NOTICE: The system will remember the previous FLAME HEIGHT setting and will automatically adjust after 10 seconds.

Adjusting Fan Speed

•Press the MENU button to activate the menu.

•Using the UP and DOWN arrows highlight the FAN icon and press SELECT.

•Use the UP and DOWN arrows to adjust the FAN SPEED, then press SELECT. The FAN SPEED can be adjusted to 3 different settings: HIGH, MEDIUM, LOW.

NOTICE: The fan has a timer built into the control module. After the fireplace is turned ON the timer will wait for 3 minutes before turning on the fan. In addition, the fan will remain on for 12 minutes after the fireplace has been turned OFF.

NOTICE: Whenever the fan is turned ON, the FAN will start up on the high setting for 10 seconds before adjusting to the previous user setting.

AUX1 Function (Unit dependent Function)

•Press the MENU button to activate the menu.

•Using the UP and DOWN arrows highlight the AUX1 icon and press SELECT.

•Use the UP and DOWN arrows to adjust the AUX1 output, then press SELECT. The AUX1 function can be adjusted to 4 different settings: HI, MED, LOW and OFF.

AUX2 Function (Unit dependent Function)

•Press the MENU button to activate the menu.

•Using the UP and DOWN arrows highlight the AUX2 icon and press SELECT.

•Use the UP and DOWN arrows to turn the AUX2 ON or OFF, then press SELECT. The AUX2 function can be either be turned ON or OFF.

NOTICE: When the fireplace is turned OFF both AUX1 and AUX2 will be turned off. The AUX1 and AUX2 functions can be activated from the remote’s OFF mode, when the flame is off. When the fireplace is turned back ON, the AUX1 and AUX2 settings will be restored to the previous setting.

62

Heat & Glo • VRT-AUB • 2123-980 Rev. H • 5/12

Page 61 Page 63
Image 62
Page 61 Page 63
Contents What to do if you smell gas Ref No GSCS20166 AS45532008SAI Global Heat & Glo VRT-AUB 2123-980 Rev. H 5/12 Listing Label Information/Location CongratulationsHomeowner Reference Information Table of Contents User GuideElectrical Information TroubleshootingGas Information Reference MaterialsLimited Lifetime Warranty Other RightsOther Rights Perth Listing and Code Approvals Operating Instructions User Guide Lighting Instructions IPI Final inspection byControl Module Operation Control ModuleFrequently Asked Questions After Fireplace is LitMaintenance and Service Logs Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection FireboxBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Framing and Clearances Selecting Appliance LocationOptional Stone Surround Installed Stone SurroundTermination Locations Vent Termination Minimum ClearancesMIN. Clearance in. mm Use of Elbows Flue InformationFlue Components Measuring StandardsFlueing Diagrams For Natural, Propane and Butane GasesNatural Gas One 90 Elbow System Natural Gas Two 90 Elbows System Minimum Maximum H1 + H2 Max 457 mm 610 mm Natural Gas Two 90 Elbows System Minimum Maximum Propane Three 90 Elbows System Minimum Maximum H1 + H2 Max + H1 + H2 = Max ft .97 m H1 Max. = 7 ft .13 m Flue Pipe Assembly Horizontal Penetration Framing StepFIG. B Minimum Clearance Assembling Slim Line Trim Ring and Heat Shield Installing Slim Line Trim Ring and Heat ShieldSlim Line Wall Thimble Vertical Termination StepSecure Flashing with NON-HARDENING Sealant Roofing Nails Vertical Flue Restrictor Twist-lock the flue cap and sealWall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall PenetrationInstall the Ceiling Firestop Pipe SLPVaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Unbolting Appliance from the Pallet Appliance SetupRemove Shipping Materials Leveling and Bolting Down the ApplianceAccessories Top to Rear Flue ConversionInstalling the Baffle On Back of AppliancePositioning the Logs Placing Mineral WoolFront Door Glass Assembly Installation Inner Glass Door Assembly ReplacementAdjustments And Replacement Parts Components Removal For ServiceParts Replacement Install Trim and/or SurroundInstalling Vent Pipe SLP Pipe Assemble Vent SectionsAssemble Slip Sections Secure The Vent SectionsInstall Decorative Ceiling Components Disassemble Vent SectionsInstall Support Brackets Install FirestopsFor Horizontal Terminations using the SLP-TRAP Flue TerminationInstall Metal Roof Flashing Heat Shield Requirements for Horizontal TerminationAssemble and Install Storm Collar Install Vertical Termination CapGas Information Gas Pressure Requirements Gas ConnectionHeat & Glo VRT-AUB 2123-980 Rev. H 5/12 Optional Accessories Requirements Wiring RequirementsIntelliFire PlusTM Ignition System Wiring Electrical InformationBlower Control Module Operation Fireplace Specific Information Kit ContentsInstallation Precautions IntroductionChanging Temperature Scale Installation of Remote Control HousingProgramming the RC300CE to the Control Module AUX300CE Module InstallationFan Installation Display Screen Idle When Remote is in on ModeStandby mode Function ButtonsAdjusting Flame Height About on ModeAbout OFF Mode Adjusting Fan SpeedSetting the Child Lock Adjusting ThermostatAdjusting Timer Power OutageFrequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire PlusIgnition System TroubleshootingSymptom Possible Cause Corrective Action IntelliFire Plus Ignition System Appliance Dimension Diagram Reference MaterialsAppliance Dimension with Stone Surround Diagram Hearth PadMaintenance Tasks Inspect Maintenance TasksCeiling Firestop Vent Components DiagramsElbow Support25 mm Vertical Termination Cap184 mm Service Parts Log Set Assembly Part number list on followingVRT-AUB VRT-AUB Contact Information

VRT-BZ-P-AUB, VRT-GY-N-AUB, VRT-BZ-N-AUB, VRT-GY-P-AUB specifications

Heat & Glo is renowned for its innovative fireplace solutions, and the LifeStyle series, including models VRT-BZ-N-AUB, VRT-GY-N-AUB, VRT-BZ-P-AUB, and VRT-GY-P-AUB, exemplifies the brand's commitment to quality and style. These contemporary fireplaces blend modern aesthetics with advanced technology, making them an ideal addition to any living space.

One of the standout features of these models is their versatile design that allows for seamless integration into any room. The LifeStyle series boasts multiple finish options, including a sleek bronze and an elegant gray, giving homeowners the flexibility to match their fireplace with their interior decor. The linear design not only promotes a minimalist look but also enhances the ambiance of any environment, serving as a captivating focal point.

In terms of technology, these fireplaces are equipped with advanced control systems, allowing users to adjust flame height, heat output, and ambiance with minimal effort. The intuitive controls can often be managed via a remote or smartphone app, providing convenience and flexibility for the modern homeowner.

Safety is also a key consideration in the LifeStyle series. With features such as automatic shut-off mechanisms and safety screens, these fireplaces prioritize user safety without compromising on style. The combustion technology employed ensures efficient heating and reduced emissions, making the LifeStyle series an environmentally conscious choice.

Additionally, with various installation options available, including built-in and wall-mounted configurations, these fireplaces can be customized to fit different spaces and preferences. This flexibility makes them perfect for both renovations and new constructions alike.

The LifeStyle series is designed for ease of maintenance, with accessible components that simplify cleaning and upkeep. This aspect is especially beneficial for busy homeowners who desire a stylish focal point in their homes without the burden of extensive maintenance demands.

In conclusion, Heat & Glo's LifeStyle VRT-BZ-N-AUB, VRT-GY-N-AUB, VRT-BZ-P-AUB, and VRT-GY-P-AUB models offer a unique combination of contemporary design, advanced technology, and user-friendly features. Whether for cozy evenings or entertaining guests, these fireplaces elevate any space while providing warmth and comfort.
Top Page Image Contents