Heat & Glo LifeStyle VRT-GY-P-AUB, VRT-GY-N-AUB, VRT-BZ-P-AUB Listing and Code Approvals

Page 9

1 Listing and Code Approvals

A. Appliance Certification

MODELS: VRT-AUB

LABORATORY: SAI Global

TYPE: Gas Space Heating Appliance

STANDARD: AS4553:2008

B. Additional Related Standards

The installation must comply with these installation instruc- tions and all relevant parts of Local and National Building Standards Regulations and those relevant recommenda- tions of the following British Standards. BS 5871: Part 1 BS 8303 BS 5440: Parts 1 & 2 BS 6891 BSEN1856 Parts 1 & 2 BS 5482 Part 1, as well as IGE/UP/7.

The Heat & Glo gas appliances discussed in this Installer’s Guide have been tested to certification standards and listed by the applicable laboratories.

This appliance must be installed in accordance with the rules in force.

NOX Class 5 for G20, NOX Class 5 for G31

C. Gas Pressure Requirements

Pressure requirements for VRT-AUB fireplaces are shown in table below.

Two taps are provided on the right hand side of the gas control for a test gauge connection to measure the inlet and outlet pressures.

 

Natural Gas

Propane

 

 

 

 

Inlet Gas Pressure

1.13

- 3.40 kPa

2.75 - 3.40 kPa

 

 

 

 

Outlet (Manifold) Gas

.80

- .95 kPa

2.36 - 2.61 kPa

Pressure

 

 

 

Max. Gas Consumption

26.7 mJ

24.5 mJ

 

 

 

Burner Injector

2.53 mm

1.45 mm

 

 

 

Burner Air Shutter

13 mm

11.5 mm

 

 

 

 

An in-line regulator MUST be installed if the gas pressure exceeds 3.40 kPa. Failure to install a regulator could damage valve.

The fireplace and its individual shut-off valve must be dis- connected from the gas supply piping system during any pressure testing of the system at test pressures in excess of 6 kPa.

If the fireplace must be isolated from the gas supply pip- ing system by closing an individual shut-off valve, it must be of the handle-less type.

WARNING! Risk of Explosion! An in-line regulator MUST be installed if the gas pressure exceeds 3.7 kPa. Failure to install a regulator could damage valve.

D. High Altitude Installations

NOTICE: If the heating value of the gas has been reduced, these rules do not apply. Check with your local gas utility or authorities having jurisdiction.

When installing above 610 meter elevation:

Reduce input rate 4% for each 305 meters feet above 610 meters.

E. Non-Combustible Materials Specification

Material which will not ignite and burn. Such materials are those consisting entirely of steel, iron, brick, tile, concrete, slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC (1832 ºF) and UL763 shall be considered non-combustible materials.

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed pa- per, plant fibers, plastics, or other material that can ignite and burn, whether flame proofed or not, or plastered or unplastered shall be considered combustible materials.

G. Electrical Codes

All electrical safety testing has been done following the EN 60335-2-102 standard. Local codes apply.

Heat & Glo • VRT-AUB • 2123-980 Rev. H • 5/12

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Ref No GSCS20166 AS45532008 SAI GlobalWhat to do if you smell gas Heat & Glo VRT-AUB 2123-980 Rev. H 5/12 Congratulations Homeowner Reference InformationListing Label Information/Location User Guide Table of ContentsGas Information TroubleshootingElectrical Information Reference MaterialsOther Rights Limited Lifetime WarrantyOther Rights Perth Listing and Code Approvals Operating Instructions User Guide Final inspection by Lighting Instructions IPIControl Module Control Module OperationAfter Fireplace is Lit Frequently Asked QuestionsMaintenance and Service Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualified Service TechnicianLogs FireboxIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Selecting Appliance Location Framing and ClearancesStone Surround Optional Stone Surround InstalledVent Termination Minimum Clearances Termination LocationsMIN. Clearance in. mm Flue Components Flue InformationUse of Elbows Measuring StandardsFor Natural, Propane and Butane Gases Flueing DiagramsNatural Gas One 90 Elbow System Natural Gas Two 90 Elbows System Minimum Maximum H1 + H2 Max 457 mm 610 mm Natural Gas Two 90 Elbows System Minimum Maximum Propane Three 90 Elbows System Minimum Maximum H1 + H2 Max + H1 + H2 = Max ft .97 m H1 Max. = 7 ft .13 m Step Flue Pipe Assembly Horizontal Penetration FramingFIG. B Minimum Clearance Installing Slim Line Trim Ring and Heat Shield Slim Line Wall ThimbleAssembling Slim Line Trim Ring and Heat Shield Step Vertical TerminationSecure Flashing with NON-HARDENING Sealant Roofing Nails Twist-lock the flue cap and seal Vertical Flue RestrictorPipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall PenetrationPipe SLP Install the Ceiling FirestopInstall Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Remove Shipping Materials Appliance SetupUnbolting Appliance from the Pallet Leveling and Bolting Down the ApplianceTop to Rear Flue Conversion AccessoriesOn Back of Appliance Installing the BafflePlacing Mineral Wool Positioning the LogsInner Glass Door Assembly Replacement Front Door Glass Assembly InstallationParts Replacement Components Removal For ServiceAdjustments And Replacement Parts Install Trim and/or SurroundAssemble Vent Sections Installing Vent Pipe SLP PipeSecure The Vent Sections Assemble Slip SectionsDisassemble Vent Sections Install Decorative Ceiling ComponentsInstall Firestops Install Support BracketsFlue Termination For Horizontal Terminations using the SLP-TRAPHeat Shield Requirements for Horizontal Termination Install Metal Roof FlashingInstall Vertical Termination Cap Assemble and Install Storm CollarGas Pressure Requirements Gas Connection Gas InformationHeat & Glo VRT-AUB 2123-980 Rev. H 5/12 IntelliFire PlusTM Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical InformationBlower Control Module Operation Installation Precautions Kit ContentsFireplace Specific Information IntroductionInstallation of Remote Control Housing Changing Temperature ScaleAUX300CE Module Installation Fan InstallationProgramming the RC300CE to the Control Module Standby mode Idle When Remote is in on ModeDisplay Screen Function ButtonsAbout OFF Mode About on ModeAdjusting Flame Height Adjusting Fan SpeedAdjusting Timer Adjusting ThermostatSetting the Child Lock Power OutageSymptom Possible Cause Corrective Action Frequently Asked Questions/TroubleshootingTroubleshooting Symptom Possible Cause Corrective ActionIntelliFire PlusIgnition System IntelliFire Plus Ignition System Reference Materials Appliance Dimension DiagramHearth Pad Appliance Dimension with Stone Surround DiagramInspect Maintenance Tasks Maintenance TasksElbow Vent Components DiagramsCeiling Firestop SupportVertical Termination Cap 184 mm25 mm Log Set Assembly Part number list on following Service PartsVRT-AUB VRT-AUB Contact Information

VRT-BZ-P-AUB, VRT-GY-N-AUB, VRT-BZ-N-AUB, VRT-GY-P-AUB specifications

Heat & Glo is renowned for its innovative fireplace solutions, and the LifeStyle series, including models VRT-BZ-N-AUB, VRT-GY-N-AUB, VRT-BZ-P-AUB, and VRT-GY-P-AUB, exemplifies the brand's commitment to quality and style. These contemporary fireplaces blend modern aesthetics with advanced technology, making them an ideal addition to any living space.

One of the standout features of these models is their versatile design that allows for seamless integration into any room. The LifeStyle series boasts multiple finish options, including a sleek bronze and an elegant gray, giving homeowners the flexibility to match their fireplace with their interior decor. The linear design not only promotes a minimalist look but also enhances the ambiance of any environment, serving as a captivating focal point.

In terms of technology, these fireplaces are equipped with advanced control systems, allowing users to adjust flame height, heat output, and ambiance with minimal effort. The intuitive controls can often be managed via a remote or smartphone app, providing convenience and flexibility for the modern homeowner.

Safety is also a key consideration in the LifeStyle series. With features such as automatic shut-off mechanisms and safety screens, these fireplaces prioritize user safety without compromising on style. The combustion technology employed ensures efficient heating and reduced emissions, making the LifeStyle series an environmentally conscious choice.

Additionally, with various installation options available, including built-in and wall-mounted configurations, these fireplaces can be customized to fit different spaces and preferences. This flexibility makes them perfect for both renovations and new constructions alike.

The LifeStyle series is designed for ease of maintenance, with accessible components that simplify cleaning and upkeep. This aspect is especially beneficial for busy homeowners who desire a stylish focal point in their homes without the burden of extensive maintenance demands.

In conclusion, Heat & Glo's LifeStyle VRT-BZ-N-AUB, VRT-GY-N-AUB, VRT-BZ-P-AUB, and VRT-GY-P-AUB models offer a unique combination of contemporary design, advanced technology, and user-friendly features. Whether for cozy evenings or entertaining guests, these fireplaces elevate any space while providing warmth and comfort.
Top Page Image Contents