Heat & Glo LifeStyle 2197-980 Vent Clearances and Framing, Pipe Clearances to Combustibles

Page 33

8 Vent Clearances and Framing

A. Pipe Clearances to Combustibles

WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles:

•Between ceiling firestops

•Between wall shield firestops

•Around vent system

Failure to keep insulation or other material away from vent pipe may cause over heating and fire.

Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).

•SLP heat shield - designed to be used on a wall 4-3/8 in. (111 mm) to 7-1/2 in. (194 mm) thick.

•If wall thickness is less than 4-3/8 in. (111 mm) the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/2 in. (194 mm) a DVP-HSM-B will be required.

B. Wall Penetration Framing

Combustible Wall Penetration

Whenever a combustible wall is penetrated, you must frame a hole for the wall shield firestop(s). The wall shield firestop maintains minimum clearances and prevents cold air infiltration.

•

The opening must be framed on all four sides using the

 

same size framing materials as those used in the wall

 

construction.

• SLP pipe - A wall shield firestop must be placed on each

 

side of an interior wall. A minimum 1-1/2 inch (38 mm)

 

overlap of attached heat shields must be maintained.

•

See Section 10.G for information for regarding the in-

3 in. (76 mm) top clearance

1 in. (25 mm) clearance around vertical sections

Heat

2-1/2 in. (64 mm)

Shield

top clearance

 

Heat

 

Shield

1 in.

1/2 in. (13 mm)

(25 mm)

bottom

clearance

clearance

bottom & sides

Wall

 

Shield

 

Firestop WALL

 

stallation of a horizontal termination cap.

Non-Combustible Wall Penetration

If the hole being penetrated is surrounded by noncom- bustible materials such as concrete, a hole with diameter one inch greater than the pipe is acceptable.

Whenever a non-combustible wall is penetrated, the wall shield firestop is only required on one side and no heat shield is necessary.

Figure 8.1 Horizontal Venting Clearances To Combustible

Materials

10 in.

(254 mm)

A

10in.

(254 mm)

B

A*

B

38 in (971 mm)

37-1/4 in. (946 mm)

*Shows center of flue framing hole. The center of the hole is 1 in. (25 mm) above the center of the horizontal flue pipe.

Figure 8.2 Wall Penetration

Heat & Glo • SOHO-N-AUB • 2197-980 Rev. F • 5/12

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents SAI Global Ref No GSCS20167 AS45532008What to do if you smell gas Do DiscardnotHeat & Glo SOHO-N-AUB 2197-980 Rev. F 5/12 Homeowner Reference Information CongratulationsUser Guide Table of ContentsTroubleshooting Appliance SetupFinishing Reference MaterialsLimited Lifetime Warranty Australian Warranty InformationWarranty Conditions and Exclusions Warranty ExclusionsOther Rights This warranty is void if HOW to ClaimPerth Listing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyClear Space Decorative Doors and FrontsFinal inspection by Lighting Instructions IPIControl Module Control Module OperationAfter Fireplace is Lit Frequently Asked QuestionsMaintenance and Service Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualified Service TechnicianLogs FireboxBurner Ignition and Operation Ember PlacementTypical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Any such action may cause a fire hazardSelecting Appliance Location Framing and ClearancesConstructing the Appliance Chase ClearancesClearances to Combustibles Combustible Mantels Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsClearance MIN. Clearance in. mmVent Information and Diagrams Two Elbows Top Vent Horizontal Termination One ElbowV1 Minimum H1 Maximum V1 Minimum H1 + H2 MaximumTop Vent Horizontal Termination Three Elbows USE SLP Series Components onlyV1 Minimum H1 Maximum V2 Minimum H2 Maximum Top Vent Vertical Termination Straight Up Vertical Flue SystemMAX. RUN V1 = 38 ft. Max .58 m V1 = 3 ft. Min mm Top Vent Vertical Termination No ElbowModel Flue System Approvals And InstallationsFlue Termination Approvals Identifying Flue ComponentsMinimum Maximum V1 = 38 ft .58 m MaximumTop Vent Vertical Termination Three Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall PenetrationPipe SLP Install the Ceiling FirestopInstall Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Securing and Leveling the Appliance Appliance PreparationParts Replacement Components Removal For ServiceAdjustments And Replacement Parts Install Trim and/or SurroundAssemble Vent Sections Installing Vent Pipe SLP PipeSecure the Vent Sections Assemble Slip SectionsDisassemble Vent Sections Install Support Brackets10 Flue Pipe & Firestop Install FirestopsFlue Termination For Horizontal Terminations using the SLP-TRAPHeat Shield Requirements for Horizontal Termination Install Metal Roof FlashingInstall Vertical Termination Cap Assemble and Install Storm CollarGas Pressure Requirements Gas Connection Gas InformationGAS Access IntelliFire PlusTM Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical InformationBlower Control Module Operation Installation Precautions Kit ContentsFireplace Specific Information IntroductionInstallation of Remote Control Housing Changing Temperature ScaleFan Installation AUX300CE Module InstallationProgramming the RC300AU to the Control Module Remote Position Learn ButtonStandby mode Idle When Remote is in on ModeDisplay Screen Function ButtonsAbout OFF Mode About on ModeAdjusting Flame Height Adjusting Fan SpeedAdjusting Timer Adjusting ThermostatSetting the Child Lock Power OutageSymptom Possible Cause Corrective Action Frequently Asked Questions/TroubleshootingFinishing Non-Combustible Materials SpecificationFraming and Finishing Instructions Mantel ProjectionsRemove Fixed Glass Assembly Appliance SetupClean the Appliance AccessoriesLog Placement Instructions Log Assembly LOGS-SOHOCE Optional Reflective Liner Rock Tray Install Media Rock KitTroubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System If the pilot continues GAS Line Electrical Access Appliance Dimension DiagramReference Materials Location Inches MillimeterInspect Maintenance Tasks Maintenance TasksSLP45 Vent Components DiagramsSLP90 SLP-HVS SLP-FSSLK-SNKD SLP-CCS-BK SLP-TVHW SLP-DCF-BK SLP-WT-BK SL-2DVPDRC-RADIUS Length 203 mm Heat Shield 384 mm Max EffectiveHorizontal Termination Cap 15-1/2 394 mmTop Vent Gas Fireplace Service PartsPart Description Comments Part Number Beginning Manufacturing Date MarchSOHO-N-AUB #13 Valve AssemblyRock Media Option Optional AccessoriesContact Information

2197-980 specifications

The Heat & Glo LifeStyle 2197-980 is a cutting-edge contemporary gas fireplace designed to seamlessly integrate into modern living spaces while providing warmth and aesthetic appeal. This model represents a perfect blend of innovative technology and stylish design, making it an excellent choice for homeowners seeking both functionality and elegance.

One of the standout features of the LifeStyle 2197-980 is its impressive heat output. With an efficiency rating that's designed to maximize warmth while minimizing energy consumption, this fireplace efficiently distributes heat throughout the room, providing a comfortable environment even during the coldest months. The unit is equipped with an advanced heating system that ensures rapid warmth without compromising on style.

Another notable characteristic is the customizable flame presentation. The LifeStyle 2197-980 offers a stunning array of flame colors and intensity settings, allowing users to create the perfect ambiance for any occasion. This fireplace utilizes the latest in LED technology to produce realistic flames that can be adjusted to fit the desired aesthetic, whether you prefer a soft glow for an intimate gathering or a robust flame for a cozy family night.

The design of the LifeStyle 2197-980 emphasizes versatility and ease of installation. It can be incorporated into various wall styles, making it an adaptable choice for different home layouts. The unit is designed for direct vent installation, which not only enhances safety but also ensures that indoor air quality remains pristine. The glass front and minimalist frame add a sophisticated touch, enhancing the overall décor of the space.

Safety is a paramount consideration in the LifeStyle 2197-980, equipped with features such as an automatic shut-off system that activates under certain conditions to prevent overheating. The fireplace also comes with a remote control, allowing users to adjust settings conveniently from anywhere in the room.

In summary, the Heat & Glo LifeStyle 2197-980 embodies modern fireplace technology with its efficient heating, customizable flames, versatile installation options, and safety features. It is an ideal choice for those who value design, comfort, and efficiency in a home heating solution, making it an investment that enhances any living space. Whether for cozy nights in or social gatherings, this fireplace stands out as a centerpiece that combines form and function beautifully.
Top Page Image Contents