Heat & Glo LifeStyle 2197-980 Assemble and Install Storm Collar, Install Vertical Termination Cap

Page 44

CAULK

Figure 10.17

J. Assemble and Install Storm Collar

CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp.

•Connect both halves of the storm collar with two screws (see Figure 10.18).

•Wrap the storm collar around the exposed pipe section closest to the roof and align brackets. Insert a bolt (provided) through the brackets and tighten the nut to complete the storm collar assembly. Make sure the collar is tight against the pipe section.

•Slide the assembled storm collar down the pipe section until it rests on the roof flashing (see Figure 10.19).

•Caulk around the top of the storm collar (see Figure 10.20).

BRACKETS

Figure 10.18 Assembling the Storm Collar

K. Install Vertical Termination Cap

•Locate and mark the flue center point on the underside of the roof, and drive a nail through the center point.

•Make the outline of the roof hole around the center point nail.

•The size of the roof hole framing dimensions depend on the pitch of the roof. There MUST BE a 1 inch (25 mm) clearance from the vertical flue pipe to combustible materials.

•Mark the roof hole accordingly.

•Cover the opening of the installed flue pipes.

•Cut and frame the roof hole.

•Use framing lumber the same size as the roof rafters and install the frame securely. Flashing anchored to the frame must withstand heavy winds.

•Continue to install concentric flue sections up through the roof hole and up past the roof line until you reach the appropriate distance above the roof.

•Attach the vertical termination cap by sliding the inner collar of the cap into the inner flue of the pipe section while placing the outer collar of the cap over the outer flue of the pipe section.

•Secure the cap by driving three self-tapping screws (supplied) through the pilot holes in the outer collar of the cap into the outer flue of the pipe (see Figure 10.20).

TERMINATION CAP

(1 of 3)

STORM

COLLAR

SCREWS

CAULK

Figure 10.20

Figure 10.19 Assembling the Storm Collar Around the Pipe

44

Heat & Glo • SOHO-N-AUB • 2197-980 Rev. F • 5/12

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Ref No GSCS20167 AS45532008 SAI GlobalWhat to do if you smell gas Do DiscardnotHeat & Glo SOHO-N-AUB 2197-980 Rev. F 5/12 Congratulations Homeowner Reference InformationTable of Contents User GuideAppliance Setup TroubleshootingFinishing Reference MaterialsAustralian Warranty Information Limited Lifetime WarrantyOther Rights Warranty Conditions and ExclusionsWarranty Exclusions Perth This warranty is void ifHOW to Claim Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Fixed Glass Assembly Remote Controls, Wall Controls and Wall SwitchesClear Space Decorative Doors and FrontsLighting Instructions IPI Final inspection byControl Module Operation Control ModuleFrequently Asked Questions After Fireplace is LitMaintenance and Service Maintenance Tasks-Qualified Service Technician Gasket Seal and Glass Assembly InspectionLogs FireboxEmber Placement Burner Ignition and OperationGetting Started Typical Appliance SystemDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Any such action may cause a fire hazardFraming and Clearances Selecting Appliance LocationClearances to Combustibles Constructing the Appliance ChaseClearances Mantel and Wall Projections Combustible MantelsTermination Locations Vent Termination Minimum ClearancesMIN. Clearance in. mm ClearanceVent Information and Diagrams Top Vent Horizontal Termination One Elbow Two ElbowsV1 Minimum H1 Maximum V1 Minimum H1 + H2 MaximumV1 Minimum H1 Maximum V2 Minimum H2 Maximum Top Vent Horizontal Termination Three ElbowsUSE SLP Series Components only MAX. RUN Top Vent Vertical TerminationStraight Up Vertical Flue System Top Vent Vertical Termination No Elbow V1 = 38 ft. Max .58 m V1 = 3 ft. Min mmFlue System Approvals And Installations ModelFlue Termination Approvals Identifying Flue ComponentsV1 = 38 ft .58 m Maximum Minimum MaximumTop Vent Vertical Termination Three Elbows Vent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationInstall the Ceiling Firestop Pipe SLPVaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Appliance Preparation Securing and Leveling the ApplianceComponents Removal For Service Parts ReplacementAdjustments And Replacement Parts Install Trim and/or SurroundInstalling Vent Pipe SLP Pipe Assemble Vent SectionsAssemble Slip Sections Secure the Vent SectionsInstall Support Brackets Disassemble Vent SectionsInstall Firestops 10 Flue Pipe & FirestopFor Horizontal Terminations using the SLP-TRAP Flue TerminationInstall Metal Roof Flashing Heat Shield Requirements for Horizontal TerminationAssemble and Install Storm Collar Install Vertical Termination CapGas Information Gas Pressure Requirements Gas ConnectionGAS Access Wiring Requirements IntelliFire PlusTM Ignition System WiringOptional Accessories Requirements Electrical InformationBlower Control Module Operation Kit Contents Installation PrecautionsFireplace Specific Information IntroductionChanging Temperature Scale Installation of Remote Control HousingAUX300CE Module Installation Fan InstallationProgramming the RC300AU to the Control Module Remote Position Learn ButtonIdle When Remote is in on Mode Standby modeDisplay Screen Function ButtonsAbout on Mode About OFF ModeAdjusting Flame Height Adjusting Fan SpeedAdjusting Thermostat Adjusting TimerSetting the Child Lock Power OutageFrequently Asked Questions/Troubleshooting Symptom Possible Cause Corrective ActionNon-Combustible Materials Specification FinishingFraming and Finishing Instructions Mantel ProjectionsAppliance Setup Remove Fixed Glass AssemblyClean the Appliance AccessoriesLog Placement Instructions Log Assembly LOGS-SOHOCE Install Media Rock Kit Optional Reflective Liner Rock TrayIntelliFire Plus Ignition System TroubleshootingSymptom Possible Cause Corrective Action If the pilot continues Appliance Dimension Diagram GAS Line Electrical AccessReference Materials Location Inches MillimeterMaintenance Tasks Inspect Maintenance TasksVent Components Diagrams SLP45SLP90 SLP-HVS SLP-FSDRC-RADIUS SLK-SNKD SLP-CCS-BK SLP-TVHWSLP-DCF-BK SLP-WT-BK SL-2DVP 203 mm Heat Shield 384 mm Max Effective LengthHorizontal Termination Cap 15-1/2 394 mmService Parts Top Vent Gas FireplacePart Description Comments Part Number Beginning Manufacturing Date March#13 Valve Assembly SOHO-N-AUBOptional Accessories Rock Media OptionContact Information

2197-980 specifications

The Heat & Glo LifeStyle 2197-980 is a cutting-edge contemporary gas fireplace designed to seamlessly integrate into modern living spaces while providing warmth and aesthetic appeal. This model represents a perfect blend of innovative technology and stylish design, making it an excellent choice for homeowners seeking both functionality and elegance.

One of the standout features of the LifeStyle 2197-980 is its impressive heat output. With an efficiency rating that's designed to maximize warmth while minimizing energy consumption, this fireplace efficiently distributes heat throughout the room, providing a comfortable environment even during the coldest months. The unit is equipped with an advanced heating system that ensures rapid warmth without compromising on style.

Another notable characteristic is the customizable flame presentation. The LifeStyle 2197-980 offers a stunning array of flame colors and intensity settings, allowing users to create the perfect ambiance for any occasion. This fireplace utilizes the latest in LED technology to produce realistic flames that can be adjusted to fit the desired aesthetic, whether you prefer a soft glow for an intimate gathering or a robust flame for a cozy family night.

The design of the LifeStyle 2197-980 emphasizes versatility and ease of installation. It can be incorporated into various wall styles, making it an adaptable choice for different home layouts. The unit is designed for direct vent installation, which not only enhances safety but also ensures that indoor air quality remains pristine. The glass front and minimalist frame add a sophisticated touch, enhancing the overall décor of the space.

Safety is a paramount consideration in the LifeStyle 2197-980, equipped with features such as an automatic shut-off system that activates under certain conditions to prevent overheating. The fireplace also comes with a remote control, allowing users to adjust settings conveniently from anywhere in the room.

In summary, the Heat & Glo LifeStyle 2197-980 embodies modern fireplace technology with its efficient heating, customizable flames, versatile installation options, and safety features. It is an ideal choice for those who value design, comfort, and efficiency in a home heating solution, making it an investment that enhances any living space. Whether for cozy nights in or social gatherings, this fireplace stands out as a centerpiece that combines form and function beautifully.
Top Page Image Contents