Heat & Glo LifeStyle 2197-980 owner manual Install Firestops, Flue Pipe & Firestop

Page 41

F. Install Firestops

For Horizontal Runs - Firestops are REQUIRED on both sides of a combustible wall through which the flue passes.

To install firestops (heat shield) for horizontal runs that pass through either interior or exterior walls:

•Cut a 1 in. x 1 in. (25 mm x 25 mm) hole through the wall.

•Position the firestops on both sides of the hole previously cut and secure the firestops with nails or screws.

•The pipe opening of the firestops MUST BE placed towards the bottom of the firestop.

•Continue the flue run through the firestop.

10 in. (254 mm)

INTERIOR

WALL SHIELD

10 in. (254 mm)

Figure 10.10 Flue Pipe & Firestop

For Vertical Runs - One firestop is REQUIRED at the hole in each ceiling through which the flue passes.

To install firestops for vertical runs that pass through ceilings:

•Position a plumb bob directly over the center of the vertical flue component.

•Mark the ceiling to establish the centerpoint of the flue.

•Drill a hole or drive a nail through this center point.

•Check the floor above for any obstructions, such as wiring or plumbing runs.

•Reposition the fireplace and flue system, if necessary, to accommodate the ceiling joists and/or obstructions.

•Cut a 9 in. x 9 in. (229 mm x 229 mm) hole through the ceiling when using SLP pipe. Use the firestop pipe open- ing as a guide.

•Frame the hole with framing lumber the same size as the ceiling joists.

 

A

 

 

 

B

 

 

CHIMNEY

 

 

HOLE

 

NEW

EXISTING CEILING

 

JOISTS

 

FRAMING

 

 

 

MEMBERS

 

CEILING

 

 

 

A

B

SLP

9 in. (229 mm)

9 in. (229 mm)

Figure 10.11 Hole and New Framing Members

If the area above the ceiling is NOT an attic, position and secure the ceiling firestop on the ceiling side of the previously cut and framed hole.

JOIST

CEILING

NAILS (4 REQUIRED)

CEILING FIRESTOP

Figure 10.12 Ceiling Firestop (Ceiling Side)

If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole.

NAILS (4 REQUIRED)

RAFTER

CEILING

CEILING FIRESTOP

Figure 10.13 Attic Firestop

Heat & Glo • SOHO-N-AUB • 2197-980 Rev. F • 5/12

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents SAI Global Ref No GSCS20167 AS45532008What to do if you smell gas Do DiscardnotHeat & Glo SOHO-N-AUB 2197-980 Rev. F 5/12 Homeowner Reference Information CongratulationsUser Guide Table of ContentsTroubleshooting Appliance SetupFinishing Reference MaterialsLimited Lifetime Warranty Australian Warranty InformationOther Rights Warranty Conditions and ExclusionsWarranty Exclusions Perth This warranty is void ifHOW to Claim Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyClear Space Decorative Doors and FrontsFinal inspection by Lighting Instructions IPIControl Module Control Module OperationAfter Fireplace is Lit Frequently Asked QuestionsMaintenance and Service Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualified Service TechnicianLogs FireboxBurner Ignition and Operation Ember PlacementTypical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Any such action may cause a fire hazardSelecting Appliance Location Framing and ClearancesClearances to Combustibles Constructing the Appliance ChaseClearances Combustible Mantels Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsClearance MIN. Clearance in. mmVent Information and Diagrams Two Elbows Top Vent Horizontal Termination One ElbowV1 Minimum H1 Maximum V1 Minimum H1 + H2 MaximumV1 Minimum H1 Maximum V2 Minimum H2 Maximum Top Vent Horizontal Termination Three ElbowsUSE SLP Series Components only MAX. RUN Top Vent Vertical TerminationStraight Up Vertical Flue System V1 = 38 ft. Max .58 m V1 = 3 ft. Min mm Top Vent Vertical Termination No ElbowModel Flue System Approvals And InstallationsFlue Termination Approvals Identifying Flue ComponentsMinimum Maximum V1 = 38 ft .58 m MaximumTop Vent Vertical Termination Three Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall PenetrationPipe SLP Install the Ceiling FirestopVaulted Ceiling Installation Install Attic Insulation ShieldFlat Ceiling Installation Securing and Leveling the Appliance Appliance PreparationParts Replacement Components Removal For ServiceAdjustments And Replacement Parts Install Trim and/or SurroundAssemble Vent Sections Installing Vent Pipe SLP PipeSecure the Vent Sections Assemble Slip SectionsDisassemble Vent Sections Install Support Brackets10 Flue Pipe & Firestop Install FirestopsFlue Termination For Horizontal Terminations using the SLP-TRAPHeat Shield Requirements for Horizontal Termination Install Metal Roof FlashingInstall Vertical Termination Cap Assemble and Install Storm CollarGas Pressure Requirements Gas Connection Gas InformationGAS Access IntelliFire PlusTM Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical InformationBlower Control Module Operation Installation Precautions Kit ContentsFireplace Specific Information IntroductionInstallation of Remote Control Housing Changing Temperature ScaleFan Installation AUX300CE Module InstallationProgramming the RC300AU to the Control Module Remote Position Learn ButtonStandby mode Idle When Remote is in on ModeDisplay Screen Function ButtonsAbout OFF Mode About on ModeAdjusting Flame Height Adjusting Fan SpeedAdjusting Timer Adjusting ThermostatSetting the Child Lock Power OutageSymptom Possible Cause Corrective Action Frequently Asked Questions/TroubleshootingFinishing Non-Combustible Materials SpecificationFraming and Finishing Instructions Mantel ProjectionsRemove Fixed Glass Assembly Appliance SetupClean the Appliance AccessoriesLog Placement Instructions Log Assembly LOGS-SOHOCE Optional Reflective Liner Rock Tray Install Media Rock KitIntelliFire Plus Ignition System TroubleshootingSymptom Possible Cause Corrective Action If the pilot continues GAS Line Electrical Access Appliance Dimension DiagramReference Materials Location Inches MillimeterInspect Maintenance Tasks Maintenance TasksSLP45 Vent Components DiagramsSLP90 SLP-HVS SLP-FSDRC-RADIUS SLK-SNKD SLP-CCS-BK SLP-TVHWSLP-DCF-BK SLP-WT-BK SL-2DVP Length 203 mm Heat Shield 384 mm Max EffectiveHorizontal Termination Cap 15-1/2 394 mmTop Vent Gas Fireplace Service PartsPart Description Comments Part Number Beginning Manufacturing Date MarchSOHO-N-AUB #13 Valve AssemblyRock Media Option Optional AccessoriesContact Information

2197-980 specifications

The Heat & Glo LifeStyle 2197-980 is a cutting-edge contemporary gas fireplace designed to seamlessly integrate into modern living spaces while providing warmth and aesthetic appeal. This model represents a perfect blend of innovative technology and stylish design, making it an excellent choice for homeowners seeking both functionality and elegance.

One of the standout features of the LifeStyle 2197-980 is its impressive heat output. With an efficiency rating that's designed to maximize warmth while minimizing energy consumption, this fireplace efficiently distributes heat throughout the room, providing a comfortable environment even during the coldest months. The unit is equipped with an advanced heating system that ensures rapid warmth without compromising on style.

Another notable characteristic is the customizable flame presentation. The LifeStyle 2197-980 offers a stunning array of flame colors and intensity settings, allowing users to create the perfect ambiance for any occasion. This fireplace utilizes the latest in LED technology to produce realistic flames that can be adjusted to fit the desired aesthetic, whether you prefer a soft glow for an intimate gathering or a robust flame for a cozy family night.

The design of the LifeStyle 2197-980 emphasizes versatility and ease of installation. It can be incorporated into various wall styles, making it an adaptable choice for different home layouts. The unit is designed for direct vent installation, which not only enhances safety but also ensures that indoor air quality remains pristine. The glass front and minimalist frame add a sophisticated touch, enhancing the overall décor of the space.

Safety is a paramount consideration in the LifeStyle 2197-980, equipped with features such as an automatic shut-off system that activates under certain conditions to prevent overheating. The fireplace also comes with a remote control, allowing users to adjust settings conveniently from anywhere in the room.

In summary, the Heat & Glo LifeStyle 2197-980 embodies modern fireplace technology with its efficient heating, customizable flames, versatile installation options, and safety features. It is an ideal choice for those who value design, comfort, and efficiency in a home heating solution, making it an investment that enhances any living space. Whether for cozy nights in or social gatherings, this fireplace stands out as a centerpiece that combines form and function beautifully.
Top Page Image Contents