Heat & Glo LifeStyle 2197-980 Covers Removal For Servicing, Components Removal For Service

Page 37

B. Covers Removal For Servicing

Control Compartment Access Door

Lift the lower door up and out to access the gas controls.

Trim Door and Glass Door

Lift the front trim door up and out away from the appliance side surrounds. Replace the door when servicing is complete.

Noting carefully how the brackets fit on the glass, release the two spring latches at the top and two at the bottom of the glass door. Carefully lift the glass up and out away from the appliance. See Figure 9.2.

Fixed Glass Assembly

WARNING! Risk of Asphyxiation! Handle fixed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches.

DO NOT strike, slam or scratch glass.

DO NOT operate fireplace with glass removed, cracked, broken or scratched.

Replace as a complete assembly.

Removing Fixed Glass Assembly

Pull the two bottom glass assembly latches off of the tabs on the glass assembly. Tip bottom of glass assembly out to remove from the appliance (see Figure 9.2).

Replacing Fixed Glass Assembly

Replace the glass door by sliding top tabs on the glass assembly under the glass clips. Position the glass down onto the bottom glass clips making sure that the glass clears the glass clip posts. Latch bottom glass clips once glass door has been properly placed on appliance.

 

GLASS

 

ASSEMBLY

 

GLASS

GLASS

CLIP POST

 

ASSEMBLY TAB

 

LATCHES

 

(BOTH BOTTOM

 

AND TOP)

 

Figure 9.2 Fixed Glass Assembly

C. Components Removal For Service

Carefully lift up and remove the logs.

Remove the base pan.

Unscrew the brackets at both ends of the burner and the top two screws locating the pilot bracket (see Figure 9.3). Slide the burner away from the burner orifice.

BURNER RETAINING SCREWS

PILOT BRACKET

RETAINING SCREWS

LOWER PILOT

BRACKET SCREWS

Figure 9.3

NOTICE: All screws which were removed must be replaced.

Pilot Assembly/Ignition System

Remove the log set and burner assembly.

Disconnect the gas supply tube from the outlet side of valve.

Disconnect the orange ignitor wire (I) and white sensor wire (S) from module.

Unscrew the pilot assembly bracket and remove, the pilot assembly along with silicone sealant grommet.

D. Parts Replacement

Fan

• Unplug the fan from the AUX300CE and slide the fan out

 

the front of the lower controls compartment.

 

Fan can be operated at 3 speed levels using RC300AU

 

 

remote and AUX300CE. Refer to RC300AU section.

 

The fan will automatically turn on after 3 minutes and will

 

stop 12 minutes after unit has been turned off.

 

Glass Panel

To replace the glass door, place the bottom edge into the lower holders, push glass against unit and secure the two spring latches at the top and bottom.

E. Adjustments And Replacement Parts

Adjustments and replacement parts for this appliance should only be done by a qualified service person. A wir- ing diagram for the appliance is shown in Section 12. A service parts list is shown in Section 16 of this manual.

F. Install Trim and/or Surround

Install optional trim kits and/or surrounds using the instructions included with the accessory.

Use non-combustible materials to cover the gap between the sheet rock and the appliance (when applicable to the model).

G. Air Shutter Setting

 

Natural Gas

Propane

Butane

SOHO-N-AUB

7/16 in

N/A

N/A

(1.1 mm)

 

 

 

Heat & Glo • SOHO-N-AUB2197-980 Rev. F • 5/12

37

Image 37
Contents SAI Global Ref No GSCS20167 AS45532008What to do if you smell gas Do DiscardnotHeat & Glo SOHO-N-AUB 2197-980 Rev. F 5/12 Homeowner Reference Information CongratulationsUser Guide Table of ContentsTroubleshooting Appliance SetupFinishing Reference MaterialsLimited Lifetime Warranty Australian Warranty InformationWarranty Exclusions Warranty Conditions and ExclusionsOther Rights HOW to Claim This warranty is void ifPerth Listing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyClear Space Decorative Doors and FrontsFinal inspection by Lighting Instructions IPIControl Module Control Module OperationAfter Fireplace is Lit Frequently Asked QuestionsMaintenance and Service Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualified Service TechnicianLogs FireboxBurner Ignition and Operation Ember PlacementTypical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Any such action may cause a fire hazardSelecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseClearances to Combustibles Combustible Mantels Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsClearance MIN. Clearance in. mmVent Information and Diagrams Two Elbows Top Vent Horizontal Termination One ElbowV1 Minimum H1 Maximum V1 Minimum H1 + H2 MaximumUSE SLP Series Components only Top Vent Horizontal Termination Three ElbowsV1 Minimum H1 Maximum V2 Minimum H2 Maximum Straight Up Vertical Flue System Top Vent Vertical TerminationMAX. RUN V1 = 38 ft. Max .58 m V1 = 3 ft. Min mm Top Vent Vertical Termination No ElbowModel Flue System Approvals And InstallationsFlue Termination Approvals Identifying Flue ComponentsMinimum Maximum V1 = 38 ft .58 m MaximumTop Vent Vertical Termination Three Elbows Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall PenetrationPipe SLP Install the Ceiling FirestopFlat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Securing and Leveling the Appliance Appliance PreparationParts Replacement Components Removal For ServiceAdjustments And Replacement Parts Install Trim and/or SurroundAssemble Vent Sections Installing Vent Pipe SLP PipeSecure the Vent Sections Assemble Slip SectionsDisassemble Vent Sections Install Support Brackets10 Flue Pipe & Firestop Install FirestopsFlue Termination For Horizontal Terminations using the SLP-TRAPHeat Shield Requirements for Horizontal Termination Install Metal Roof FlashingInstall Vertical Termination Cap Assemble and Install Storm CollarGas Pressure Requirements Gas Connection Gas InformationGAS Access IntelliFire PlusTM Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical InformationBlower Control Module Operation Installation Precautions Kit ContentsFireplace Specific Information IntroductionInstallation of Remote Control Housing Changing Temperature ScaleFan Installation AUX300CE Module InstallationProgramming the RC300AU to the Control Module Remote Position Learn ButtonStandby mode Idle When Remote is in on ModeDisplay Screen Function ButtonsAbout OFF Mode About on ModeAdjusting Flame Height Adjusting Fan SpeedAdjusting Timer Adjusting ThermostatSetting the Child Lock Power OutageSymptom Possible Cause Corrective Action Frequently Asked Questions/TroubleshootingFinishing Non-Combustible Materials SpecificationFraming and Finishing Instructions Mantel ProjectionsRemove Fixed Glass Assembly Appliance SetupClean the Appliance AccessoriesLog Placement Instructions Log Assembly LOGS-SOHOCE Optional Reflective Liner Rock Tray Install Media Rock KitSymptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System If the pilot continues GAS Line Electrical Access Appliance Dimension DiagramReference Materials Location Inches MillimeterInspect Maintenance Tasks Maintenance TasksSLP45 Vent Components DiagramsSLP90 SLP-HVS SLP-FSSLP-DCF-BK SLP-WT-BK SL-2DVP SLK-SNKD SLP-CCS-BK SLP-TVHWDRC-RADIUS Length 203 mm Heat Shield 384 mm Max EffectiveHorizontal Termination Cap 15-1/2 394 mmTop Vent Gas Fireplace Service PartsPart Description Comments Part Number Beginning Manufacturing Date MarchSOHO-N-AUB #13 Valve AssemblyRock Media Option Optional AccessoriesContact Information

2197-980 specifications

The Heat & Glo LifeStyle 2197-980 is a cutting-edge contemporary gas fireplace designed to seamlessly integrate into modern living spaces while providing warmth and aesthetic appeal. This model represents a perfect blend of innovative technology and stylish design, making it an excellent choice for homeowners seeking both functionality and elegance.

One of the standout features of the LifeStyle 2197-980 is its impressive heat output. With an efficiency rating that's designed to maximize warmth while minimizing energy consumption, this fireplace efficiently distributes heat throughout the room, providing a comfortable environment even during the coldest months. The unit is equipped with an advanced heating system that ensures rapid warmth without compromising on style.

Another notable characteristic is the customizable flame presentation. The LifeStyle 2197-980 offers a stunning array of flame colors and intensity settings, allowing users to create the perfect ambiance for any occasion. This fireplace utilizes the latest in LED technology to produce realistic flames that can be adjusted to fit the desired aesthetic, whether you prefer a soft glow for an intimate gathering or a robust flame for a cozy family night.

The design of the LifeStyle 2197-980 emphasizes versatility and ease of installation. It can be incorporated into various wall styles, making it an adaptable choice for different home layouts. The unit is designed for direct vent installation, which not only enhances safety but also ensures that indoor air quality remains pristine. The glass front and minimalist frame add a sophisticated touch, enhancing the overall décor of the space.

Safety is a paramount consideration in the LifeStyle 2197-980, equipped with features such as an automatic shut-off system that activates under certain conditions to prevent overheating. The fireplace also comes with a remote control, allowing users to adjust settings conveniently from anywhere in the room.

In summary, the Heat & Glo LifeStyle 2197-980 embodies modern fireplace technology with its efficient heating, customizable flames, versatile installation options, and safety features. It is an ideal choice for those who value design, comfort, and efficiency in a home heating solution, making it an investment that enhances any living space. Whether for cozy nights in or social gatherings, this fireplace stands out as a centerpiece that combines form and function beautifully.