Desa (V)KC42PE Continued, Installing Lava Rock and Glowing Embers, page, Handset

Page 26
Installing Lava Rock and Glowing Embers, page 25.

Fireplace

Installation

Continued

7.Remove three screws from deflector shield on the inside top of firebox. Set shield and screws aside.

8.Install rear brick panel first. Rest bottom edge of panel on back edge of burner assembly (see Figure 39).

9.Install left side brick panel by sliding it be- tween the burner assembly and the side of the firebox (see Figure 39).

10.Install the right brick panel using the same method described in step 6 for left brick panel.

11.Replace deflector shield using screws removed in step 7.

12.Using screws removed in step 6, replace plenum and attach to burner.

13.Carefully replace the ember pod and log set.

14.Use screws removed in step 4 to replace andiron assembly.

15.Install lava rock and glowing embers. See

Installing Lava Rock and Glowing Embers, page 25.

16.Close glass door and lock latches on top and bottom of door and replace screen. See Re- moving Glass Door, steps 5 and 6, page 25.

17.Replace top and bottom louvers.

Left Side Brick

Panel

WALL SWITCH INSTALLATION

The installation of a wall switch allows you to ac- tivate the gas control valve and turn the fireplace on and off. The wall switch is to be connected to the incoming 120 volt regular household wiring that supplies the electricity to the fireplace.

optional Remote control INSTALLATION (model WRC)

Note: If using optional wireless hand-held remote control, the wall switch must be in the ON position to be operational. The remote control then becomes the switching mechanism for fireplace operation.

1.Open lower louver panel.

2.The WRC model receiver does not require a battery. The receiver can be installed by first plugging the short extension cord into the fireplace receptacle. Then plug the receiver unit into the extension cord. Finally plug the ignition module plug into the receiver unit (see Figure 40).

3.Activate the remote handset battery by removing the insulating tab on the back of the handset (see Figure 41). The battery is included pre-installed.

4.Once the battery is activated the unit is ready to use.

5.Close lower louver panel.

Remote

FireplaceControl

Receptacle Figure 40 - Installing the WRC RemoteFigure 39 - Installing Rear Brick PanelFigure 41 - Installing Battery into Back of Receiver

Extension Cord

Ignition

Module Plug

 

Figure 40 - Installing the WRC Remote

Receiver

HandsetBattery Cover

12 Volt Battery

Rear Brick Panel

Figure 39 - Installing Rear Brick Panel

Back of

Pull to Remove

Handset

Insulation Tab

 

Figure 41 - Installing Battery into Back of

Handset

26

www.desatech.com

116240-01E

Page 25 Page 27
Image 26
Page 25 Page 27
Contents WHAT TO DO IF YOU SMELL GAS DANGER Carbon monoxide Table of ContentsSafety Information poisoning may lead to deathSafety information ContinuedIdentification Safety informationProduct Local CodesFigure 3 - Fireplace Bottom Dimensions Product FeaturesPre-Installation Preparation Location and space requirementsContinued ClearancesPreparation Pre-InstallationInstallation ContinuedFigure 7 - Minimum Clearances for Termination Cap Location of Termination CapD E B L Venting Installation Instructions Continued Venting Installation instructionsINSTALLATION PLANNING Figure 8 - Vent Pipe ConnectionsFigure 12 - Connecting Vent Cap with Figure 10 - Installing Horizontal Vent CapFigure 11 - Installing Siding Standoff ContinuedSquare Termination GROUND FLOOR INSTALLATIONContinued VerticalContinued CORNER INSTALLATIONSNORKEL TERMINATION INSTALLATION 90 ElbowContinued HORIZONTAL SYSTEM INSTALLATIONUSING TWO 90 ELBOWS with Termination at 90 with FireplaceFigure 20 - Installing Firestop installation for vertical terminationFlat Ceiling Installation ContinuedContinued Configuration Using Two 90 ElbowsConfiguration Using One 90 Elbow Figure 21 - Vertical VentingContinued Configuration Using Two 90 ElbowsConfiguration With No Horizontal Run Vertical VentingDESA 5/8 Pipe & Vent Kits Number Description parts list for venting kits and componentsContinued Number DescriptionCHECK GAS TYPE Fireplace InstallationInstalling optional blower accessories Figure 28 - Blower Model BKT Model BKT InstallationContinued Installation Items Needed Installing Gas Piping to Fireplace LocationBlower Wiring Diagram Figure 30 - External Regulator with Vent Installation Items NeededContinued Pointing Down Propane/LP OnlyContinued CHECKING GAS CONNECTIONSFigure 36 - Removing Louver Panel Pressure Testing Fireplace Gas ConnectionsRemoving Louver Panels Removing Glass DoorInstalling lava rock and glowing embers Figure 39 - Installing Rear Brick Panel Installing Lava Rock and Glowing Embers, pageFigure 40 - Installing the WRC Remote Receiver Figure 41 - Installing Battery into Back of24V AC IGNITOR LEADPILOT 120V AClighting instructions for your safety Read before lightingOperating Fireplace TO TURN OFF GAS TO APPLIANCEContinued see Troubleshooting, pagesee Troubleshooting, page Figure 44 - Correct Pilot Flame PatternCleaning and Maintenance CAUTION Do not vacuum if pieces are hotOBSERVED PROBLEM Cleaning and MaintenanceTroubleshooting venting systemContinued TROUBLESHOOTINGWiring Diagram, page WARNING If you smell gas Shut off gas supply Technical Service Replacement PartsService Hints SpecificationsAccessories 116240-01E 24 22 23 4 1 9 11 3 14 167 8 PARTS LIST illustrated parts breakdown Burner Pan Assembly LIMITED WARRANTY DIRECT-VENTFIREPLACE Warranty InformationKEEP THIS WARRANTY
Top Page Image Contents