Desa EFS33PRA BUILT-IN Fireplace Installation, Mantel Clearances for Built-In Installation

Page 10

10

INSTALLATION

Built-In Fireplace Installation

INSTALLATION

Continued

BUILT-IN FIREPLACE INSTALLATION

Built-in installation of this fireplace involves installing fireplace into a framed-in enclosure. This makes the front of fireplace flush with wall. If installing a mantel above the fireplace, you must follow the clearances shown in Figure 16, page 11. Follow the instructions below to install the fireplace in this manner.

 

Actual

 

Framing

 

 

 

 

Height

32 3/8"

 

33"

Front Width

34

5/

16

"

35

1/ "

 

 

 

 

 

 

2

Depth

16

11/

16

"

17

3/ "

 

 

 

 

 

 

4

1.Frame in rough opening. Use dimensions shown in Figure 13 for the rough opening.If installing in a corner, use dimensions shown in Figure 14 for the rough opening. The height is 33" which is the same as the wall opening above.

2.If using blower, install and properly ground GA3555, three- prong 120 volt electrical outlet, in fireplace. Follow instruc- tions included in kit.

3.Install gas piping into fireplace location. This installation in- cludes an approved flexible gas line (if allowed by local codes) after the equipment shutoff valve. The flexible gas line must be the last item installed on the gas piping. See Installing Gas Piping to Fireplace Location, pages 11 and 12.

4.Carefully set fireplace in front of rough opening with back of fireplace inside wall opening.

5.Carefully insert fireplace into rough opening.

6.Attach flexible gas line to gas supply. See Connecting Fire- place to Gas Supply, page 12.

7.Attach fireplace to wall studs using nails or wood screws through holes in nailing flange (see Figure 15).

8.Check all gas connections for leaks. See Checking Gas Con- nections, page 13.

9.Plug electrical cord into electrical outlet installed in step 2.

10.Install brass trim after final finishing and/or painting of wall (see Figure 7, page 8).

17 3/4"

33"

35 1/2"

Figure 13 - Rough Opening for Installing in Wall

39 3/8"

27 7/8"

35 1/2" 55 5/8"

Figure 14 - Rough Opening for Installing in Corner

Nails or

Wood

Screws

Nailing Flanges

Figure 15 - Attaching Fireplace to Wall Studs

Mantel Clearances for Built-In Installation

If placing mantel above built-in fireplace, you must meet minimum clearance between mantel shelf and top of fireplace opening.

NOTICE: If your installation does not meet the mini- mum clearances shown, you must do one of the following:

raise the mantel to an acceptable height

remove the mantel

Forvisit..com

107172-01J

Image 10
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASTable of Contents Safety InformationLog Base Assembly VSGF33NRA Shown Product IdentificationUnpacking Product FeaturesLocal Codes AIR for Combustion and VentilationUnusually Tight Construction Providing Adequate VentilationDetermining FRESH-AIR Flow for Heater Location Confined and Unconfined SpaceVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationInstalling Hood Electrical HookupIncluded with Mantel Accessory Installation ClearancesConventional Fireplace Installation Assembling and Attaching Optional Brass TrimPlacing Hearth Base Accessory Against Wall BUILT-IN Fireplace Installation Mantel Clearances for Built-In InstallationInstalling GAS Piping to Fireplace Location Installation Items NeededConnecting Fireplace to GAS Supply Gas ConnectionPressure Testing Fireplace Gas Connections Pressure Testing gas Supply Piping systemChecking GAS Connections Place front log on top of the grate. Make sure the notches Installing Fireplace Screen Operating Fireplace For Your Safety Read Before LightingLighting Instructions Optional HAND-HELD Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance ON/OFF Series Models Ghrcb and CghrcbOptional Blower Operation Inspecting BurnersPilot Flame Pattern Main Burner Cleaning MaintenanceCleaning Burner Injector Holder and Pilot AIR Inlet Hole Front Burner Flame PatternLogs Wiring DiagramSpecifications Models EFS33NR, EFS33NRA, VSGF33NR, and VSGF33NRATroubleshooting Observed Problem Possible Cause RemedyMaintenance, For more Visit www Com Illustrated Parts Breakdown Parts List Not a field replaceable partModels EFS33NR, EFS33NRA, VSGF33NR, VSGF33NRA KEY Part Number Description QTY Accessories Hardwood Hearth Base Cabinet Mantel and Full Hearth BaseCorner Hearth Base Laminate Trim for Hearth or MantelService Hints Replacement PartsTechnical Service Owners Registration Form Tape 107172-01J Warranty Information